Home > Motorola > Wireless > Motorola Wing 5 Manual

Motorola Wing 5 Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Motorola Wing 5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 249 Motorola manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1128
    Add page 991 to Favourites
    image text
    Enable zoom 
    							SMART-RF-POLICY 21 - 9
• coverage-hole-recovery {snr-threshold [2.4Ghz|5Ghz] }
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#coverage-hole-recovery snr-threshold 
5GHz 1
rfs7000-37FABE(config-smart-rf-policy-test)#
rfs7000-37FABE(config-smart-rf-policy-test)#show context
smart-rf-policy test
 auto-assign-sensor
 assignable-power 5GHz min 8
 assignable-power 5GHz max 20
 channel-list 2.4GHz 1,12
 channel-width 5GHz auto
 sensitivity custom
 coverage-hole-recovery snr-threshold 5GHz 1
rfs7000-37FABE(config-smart-rf-policy-test)#
Related Commands
2.4GHz  Specifies coverage hole recovery interval on the 2.4GHz band
  – Sets a value from 1 - 120 seconds. The default is 10 seconds.
5GHz  Specifies coverage hole recovery interval on the 5GHz band
  – Sets a value from 1 - 120 seconds. The default is 10 seconds.
snr-threshold Optional. Specifies the SNR threshold value. This value is the signal to noise ratio 
threshold for an associated client as seen by its associated AP radio. When the SNR 
threshold is exceeded, the radio increases its transmit power to increase the coverage 
for the associated client.
2.4GHz  Specifies SNR threshold on the 2.4GHz band
  – Sets a value from 1 - 75. The default is 20dB.
5GHz  Specifies SNR threshold on the 5GHz band
  – Sets a value from 1 - 75. The default is 20dB.
noDisables recovery from coverage hole errors
    Add page 992 to Favourites
    image text
    Enable zoom 
    							21 - 10 WiNG CLI Reference Guide
21.1.6 enable
smart-rf-policy
Enables a Smart RF policy
Use this command to enable this Smart RF policy. Once enabled, the policy can be assigned to a RF Domain or used for 
wireless controller network support.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
enable
Parameters
None
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#enable
rfs7000-37FABE(config-smart-rf-policy-test)#show context
smart-rf-policy test
 auto-assign-sensor
 assignable-power 5GHz min 8
 assignable-power 5GHz max 20
 channel-list 2.4GHz 1,12
 channel-width 5GHz auto
 sensitivity custom
 coverage-hole-recovery snr-threshold 5GHz 1
rfs7000-37FABE(config-smart-rf-policy-test)#
rfs7000-37FABE(config-smart-rf-policy-test)#
Related Commands
noDisables a Smart RF policy
    Add page 993 to Favourites
    image text
    Enable zoom 
    							SMART-RF-POLICY 21 - 11
21.1.7 group-by
smart-rf-policy
Configures Smart RF grouping values
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
group-by [area|floor]
Parameters
• group-by [area|floor]
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#group-by floor
rfs7000-37FABE(config-smart-rf-policy-test)#show context
smart-rf-policy test
 auto-assign-sensor
 group-by floor
 assignable-power 5GHz min 8
 assignable-power 5GHz max 20
 channel-list 2.4GHz 1,12
 channel-width 5GHz auto
 sensitivity custom
 coverage-hole-recovery snr-threshold 5GHz 1
rfs7000-37FABE(config-smart-rf-policy-test)#
Related Commands
area Configures a group based on area
floor Configures a group based on floor
noRemoves Smart RF group settings
    Add page 994 to Favourites
    image text
    Enable zoom 
    							21 - 12 WiNG CLI Reference Guide
21.1.8 interference-recovery
smart-rf-policy
Recovers excessive noise and interference. Enabling interference recovery ensures that noise levels and other RF 
parameters are continuously monitored on a radio’s current channel. When noise levels exceed the specified noise 
threshold, Smart RF switches to another channel with less interference.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
interference-recovery {channel-hold-time|channel-switch-delta|client-threshold|
interference|noise|noise-factor}
interference-recovery {channel-switch-delta [2.4GHz|5GHZ] []}
interference-recovery {channel-hold-time []|client-threshold []|
interference|noise|noise-factor []}
Parameters
• interference-recovery {channel-switch-delta [2.4GHz|5GHZ] []}
channel-switch-delta Optional. Specifies the difference between the current and best channel interference for 
a channel change
[2.4GHz|5GHz] Selects the band
 2.4GHz – Selects the 2.4GHz band
 5GHz – Selects the 5GHz band
 Specifies the difference between the current and best channel interference
  – Sets a value from 5 - 35 dBm
    Add page 995 to Favourites
    image text
    Enable zoom 
    							SMART-RF-POLICY 21 - 13
• interference-recovery {channel-hold-time []|client-threshold []|
interference|noise|noise-factor []}
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#interference-recovery channel-switch-
delta 5 5
rfs7000-37FABE(config-smart-rf-policy-test)#interference-recovery interference
rfs7000-37FABE(config-smart-rf-policy-test)#show context
smart-rf-policy test
 auto-assign-sensor
 group-by floor
 assignable-power 5GHz min 8
 assignable-power 5GHz max 20
 channel-list 2.4GHz 1,12
 channel-width 5GHz auto
 sensitivity custom
 coverage-hole-recovery snr-threshold 5GHz 1
 interference-recovery channel-switch-delta 5GHz 5
rfs7000-37FABE(config-smart-rf-policy-test)#
Related Commands
channel-hold-time 
 Optional. Defines the minimum time between two channel change recoveries
  – Sets the time between channel change assignments based on 
interference or noise in seconds
client-threshold  Optional. Specifies client thresholds to avoid channel changes (when exceeded).
  – Sets the number of clients from 1 - 255
interference Optional. Considers external interference values to perform interference recovery
noise Optional. Considers noise values to perform interference recovery
noise-factor 
Optional. Configures additional noise factor for non-wifi interference
  – Sets a noise factor from 1.0 - 3.0
noDisables recovery from excessive noise and interference
    Add page 996 to Favourites
    image text
    Enable zoom 
    							21 - 14 WiNG CLI Reference Guide
21.1.9 neighbor-recovery
smart-rf-policy
Enables recovery from errors due to faulty neighbor radios. Enabling neighbor recovery ensures automatic recovery when 
a radio fails within the radio coverage area. Smart RF instructs neighboring access points to increase their transmit power 
to compensate for the failed radio.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
neighbor-recovery {dynamic-sampling|power-hold-time|power-threshold}
neighbor-recovery {dynamic-sampling {retries []|threshold []}}
neighbor-recovery {power-hold-time []}
neighbor-recovery {power-threshold [2.4Ghz|5Ghz] []}
Parameters
• neighbor-recovery {dynamic-sampling {retries []|threshold 
[]}}
• neighbor-recovery {power-hold-time []}
dynamic-sampling Optional. Configures dynamic sampling on this Smart RF policy
retries  Optional. Specifies the number of retries before allowing a power change
  – Sets the number of retries from 1 - 10
threshold  Optional. Specifies the minimum number of sample reports before which a power change 
requires dynamic sampling
  – Sets the minimum number of reports from 1 - 30
power-hold-time Optional. Specifies the minimum time between two power change recoveries
 Sets the time from 0 - 3600 seconds
    Add page 997 to Favourites
    image text
    Enable zoom 
    							SMART-RF-POLICY 21 - 15
• neighbor-recovery {power-threshold [2.4Ghz|5Ghz] []}
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#neighbor-recovery power-threshold 2.4 -
82
rfs7000-37FABE(config-smart-rf-policy-test)#neighbor-recovery power-threshold 5 -65
rfs7000-37FABE(config-smart-rf-policy-test)#show context
smart-rf-policy test
 auto-assign-sensor
 group-by floor
 assignable-power 5GHz min 8
 assignable-power 5GHz max 20
 channel-list 2.4GHz 1,12
 channel-width 5GHz auto
 sensitivity custom
 interference-recovery channel-switch-delta 5GHz 5
 neighbor-recovery power-threshold 5GHz -65
 neighbor-recovery power-threshold 2.4GHz -82
 coverage-hole-recovery snr-threshold 5GHz 1
rfs7000-37FABE(config-smart-rf-policy-test)#
Related Commands
power-threshold Optional. Specifies the power threshold based on the recovery performed
[2.4GHz|5GHz] Selects the band
 2.4GHz – Selects the 2.4GHz band
 5GHz – Selects the 5GHz band
 Specify the threshold value
  – Sets the power threshold from -85 - -55 dBm
noDisables recovery from faulty neighbor radios
    Add page 998 to Favourites
    image text
    Enable zoom 
    							21 - 16 WiNG CLI Reference Guide
21.1.10 no
smart-rf-policy
Negates a command or sets its default. When used in the config Smart RF policy mode, the no command disables or resets 
Smart RF settings.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532

AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
no [assignable-power|auto-assign-sensor|channel-list|channel-width|
coverage-hole-recovery|enable|group-by|interference-recovery|neighbor-recovery|
smart-ocs-monitoring]
Parameters
• no [assignable-power|auto-assign-sensor|channel-list|channel-width|
coverage-hole-recovery|enable|group-by|interference-recovery|neighbor-recovery|
smart-ocs-monitoring]
no assignable-power Resets assignable power to its default
no auto-assign-sensor Disables auto assignment of sensor radios to its default
no channel-list Resets the channel list for the selected frequency to its default
no channel-width Resets channel width for the selected frequency to its default
no coverage-hole-recovery Disables recovery from coverage hole errors
no enable Disables a Smart RF policy
no group-by Removes a Smart RF policy’s group settings
no interference-recovery Disables recovery from errors due to excessive noise and interference
no neighbor-recovery Disables recovery from errors due to faulty neighbor radios
no smart-ocs-monitoring Disables off channel monitoring
When used on an AP7161 model access point, this command disables a meshpoint.
    Add page 999 to Favourites
    image text
    Enable zoom 
    							SMART-RF-POLICY 21 - 17
Examples
The following is the Smart RF policy settings before the execution of the no command:
rfs7000-37FABE(config-smart-rf-policy-test)#show context
smart-rf-policy test
 group-by floor
 sensitivity custom
 interference-recovery channel-switch-delta 5GHz 5
 neighbor-recovery power-threshold 5GHz -65
 neighbor-recovery power-threshold 2.4GHz -82
 coverage-hole-recovery snr-threshold 5GHz 1
rfs7000-37FABE(config-smart-rf-policy-test)#
rfs7000-37FABE(config-smart-rf-policy-test)#no interference-recovery channel-switch-
delta 5GHz
rfs7000-37FABE(config-smart-rf-policy-test)#no neighbor-recovery power-threshold  
2.4GHz
rfs7000-37FABE(config-smart-rf-policy-test)#no neighbor-recovery power-threshold
 5GHz
The following is the Smart RF policy settings after the execution of the no command:
rfs7000-37FABE(config-smart-rf-policy-test)#show context smart-rf-policy test
rrfs7000-37FABE(config-smart-rf-policy-test)#
Related Commands
assignable-powerAssigns the power range
auto-assign-sensorAllows Smart RF to automatically select optimal sensor radios for WIPS and unauthorized 
AP detection
channel-listAssigns the channel list for the selected frequency
channel-widthSelects the channel width for Smart RF configuration
coverage-hole-recoveryEnables recovery from coverage hole errors
enableEnables the configured Smart RF policy features
group-byConfigures grouping parameters on this Smart RF policy
interference-recoveryEnables recovery of errors due to excessive noise and interference
neighbor-recoveryEnables recovery of faulty neighbor radios
smart-ocs-monitoringApplies smart off channel scanning instead of dedicated detectors
smart-ocs-monitoring 
(ap7161)Applies smart off channel scanning instead of dedicated detectors
When used on an AP7161 model, this command configures a radio meshpoint on the 
selected band.
    Add page 1000 to Favourites
    image text
    Enable zoom 
    							21 - 18 WiNG CLI Reference Guide
21.1.11 sensitivity
smart-rf-policy
Configures Smart RF sensitivity
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
sensitivity [custom|high|low|medium]
Parameters
• sensitivity [custom|high|low|medium]
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#sensitivity high
smart-rf-policy test
 sensitivity high
 smart-ocs-monitoring frequency 5GHz 3
 smart-ocs-monitoring frequency 2.4GHz 3
 smart-ocs-monitoring sample-count 2.4GHz 3
 smart-ocs-monitoring extended-scan-frequency 5GHz 0
 smart-ocs-monitoring extended-scan-frequency 2.4GHz 0
 interference-recovery client-threshold 255
 interference-recovery channel-switch-delta 5GHz 5
 interference-recovery channel-switch-delta 2.4GHz 5
 neighbor-recovery power-threshold 5GHz -65
 neighbor-recovery power-threshold 2.4GHz -65
 no coverage-hole-recovery
 coverage-hole-recovery coverage-interval 5GHz 5
 coverage-hole-recovery coverage-interval 2.4GHz 5
 coverage-hole-recovery client-threshold 5GHz 0
 coverage-hole-recovery client-threshold 2.4GHz 0
 interference-recovery channel-hold-time 180
sensitivity Configures Smart RF sensitivity levels
custom Custom sensitivity. Enables interference recovery, coverage hole recovery, and neighbor 
recovery as additional Smart RF options
high High sensitivity
low Low sensitivity
medium Medium sensitivity. This is the default setting.
    All Motorola manuals Comments (0)