Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
33 Argentina 
DID Trunk Group Administration
                                                               Page   4 of 10
                                     TRUNK GROUP
                                      Administered Members (min/max):   0/0
GROUP MEMBER ASSIGNMENTS                  Total Administered Members:   0
Port     Code     Sfx    Name        Night       Mode       Type       Ans Delay
1: 
2: 
3: 
                                                                Page   1 of 10
                                   TRUNK GROUP
Group Number:                     Group Type: did            CDR Reports: y
  Group Name: OUTSIDE CALL               COR: 1        TN: 1         TAC:
                            Country: 7
                                   Auth Code? n
TRUNK PARAMETERS
            Trunk Type: immed-start         Incoming Rotary Timeout(sec): 5
    Incoming Dial Type: tone
     Trunk Termination: rc                       Disconnect Timing(msec): 500
       Digit Treatment:                                           Digits:
       Expected Digits:                                Sig Bit Inversion: none
     Terminal Balanced? n                                  RA Trunk Loss: 0db
   Extended Loop Range? n          Trunk Gain: high       Drop Treatment: silence
 Disconnect Supervision - In? y
                                                                 Page   2 of 10
TRUNK FEATURES
          ACA Assignment? n      Measured: none
                                                         Maintenance Tests? y
                         Data Restriction? n
   Suppress # Outpulsing? n 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
34 Argentina 
Digital Trunk Administration
This sec tion d oes not list all p ossib le valid  ad ministrable c omb inations. Rather 
the most c ommon or stand ard c ombination, c omp atib le with p ub lic -network and  
Typ e Ap proval stand ard s for eac h c ountry, is p resented .
                                                                 Page   3 of 10
                                    TRUNK GROUP
ADMINISTRABLE TIMERS
   Incoming Disconnect(msec): 500
   Incoming Dial Guard(msec): 70
          Flash Length(msec): 540      Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
    Tone(msec): 350      Pause(msec): 150
                                                                 Page   4 of 10
                                    TRUNK GROUP
                                      Administered Members (min/max):   0/0
GROUP MEMBER ASSIGNMENTS                  Total Administered Members:   0
Port        Code         Sfx        Name
1: 
2: 
3:  
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
35 Argentina 
DS1 Programing for CO, DID and DIOD trunks 
to the PTT using digital trunks
Tie Trunks
nNon-ISDN Sig naling  Examp le (DS1 Ad ministration Sc reen)
— Circ uit Pac k: TN464D (Not entered  as ad ministrab le item)
— Bit Rate: 2.048
— Interfac e Comp anding : mu-law
— Line Cod ing: HDB3
— Sig naling  Mod e: CAS
— Country Protoc ol: 16 
— Interc onnec t: p b x
—CRC?: no
— Id le Cod e: 01010100 
— ISDN-PRI (Private Network) Sig naling  This examp le assumes use of 
US Op tion 1 with fac ility assoc iated  sig naling . Other feature op tions 
will req uire c hang es in one or more ad ministered  items.
— DS1 Ad ministration sc reen
nCirc uit Pac k: TN464D (or TN464C from up g rad es)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: isdn-pri
nCountry Protoc ol: 1
                                                                Page   1 of  1
                                 DS1 CIRCUIT PACK
            Location:                               Name: E-1CO, DID, DIOD
            Bit Rate: 2.048                  Line Coding: hdb3
      Signaling Mode: CAS
        Interconnect: CO                Country Protocol: 7
Interface Companding: alaw                           CRC? n
           Idle Code: 11111111
 MAINTENANCE PARAMETERS
      Slip Detection? n                Near-end CSU Type: none 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
36 Argentina 
— Connec t: p b x
— Interfac e: user 
—CRC: No
— Id le Cod e: 01010100 
n Signaling Group screen
— Assoc iated Sig naling : Yes
— Primary D_Channel: xxxx16 (xxxx= > dep end s on CP p hysic al 
loc ation)
nTrunk Group  Ad ministration sc reen
— Group Type: isdn-pri
— Servic e Type: tie
nISDN-PRI (Public  Network)
Not availab le for this c ountry. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
37 Australia 
Australia
Ta b l e  1 6 shows the rec ommended  c irc uit p ac ks.
Table 16. Recommended and Available CPs in Australia
Equipment Equipment Type
Cab inet Typ e & Power GAC-MCC DC-MCC AC-SCC DC-SCC 
AC-CSCC AC-CMC
AC Power Voltag e & Freq 240V/50Hz 
Ring  Generator 20Hz 25Hz
Tone Detec tor > TN2182B > TN744D TN420C TN420B 
Tone Cloc k > TN2182B TN780 TN419B
R2MFC Circ uit n/a 
Sp eec h Synthesizer > TN457 
Call Classifier > TN744D
Announc ement > TN750C TN750B 
Analog DID Trunk > TN436B TN436
Analog  CO Trunk (No PPM)  > TN2147C TN22147
Analog  CO Trunk (w/PPM) #TN465C > TN438B
4 Wire Tie Trunk TN437B TN437
2 Wire Tie Trunk > TN439 
Auxiliary Trunk #TN763D > TN417 
Dig ital CO/DID Trunk n/a 
Dig ital Tie Trunk > TN464F TN464E TN464D TN464C 
Dig ital PRI CO Trunk > TN464F TN464E TN464D TN464C 
Dig ital BRI Trunk > TN2185
Dig ital Converter PRI-DASS   
Dig ital Converter PRI-DPNSS TN-CCSC-2
Dig ital Converter PRI-BRI   
8 Port Analog  Line TN467 
16 Port Analog  Line #TN2183 > TN468B TN468
24 Port Analog  Line TN2793
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
38 Australia 
NOTE:
Australia P2 sig naling req uires TN464Fv5 or later.
Country-Specific Features
When the Country Code is 2, Malic ious Call Trac e notific ation is p assed  over the 
following  ISDN-PRI trunk g roup s: tand em, tie, ac c ess, and  DMI-BOS. See 
“ Malic ious Call Trac e”  in 
D EFINITY EC S Ad ministrator’s Guid e.
Feature Administration
The sc reen d isp lays shown in this sec tion were effec tive the d ate the typ e 
ap p roval was award ed . The sc reens may have c hang ed  sinc e that d ate.
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nARS/AAR Ad ministration
To enab le ARS administration, on the System-Parameters 
Customer-Op tions sc reen, set the ARS
 field  to y
. You also should check all 
ARS/AAR d efaults. All d efault ARS analysis c odes are deleted  b efore 
d ialed  strings are ad d ed for routing when DEFINITY is installed  outsid e of 
North Americ a. Be aware that the d efault for the 10 d ig its c ause dialing 
p rob lems. In p artic ular, the following  c all typ es (ap pear as ARS/AAR 
d efaults) typ ic ally are not used  in non-North Americ an ARS/AAR tab les: 4 Wire Digital Line > TN754B TN413
2 Wire Digital Line #TN2224 > TN2181
Data Line > TN726B 
BRI-U Line
BRI-ST Line TN556B 
fnp a: North Americ an numb ers with an area c od e.
hnp a: North Americ an numb ers without an area c od e.
svc : North Americ an numb ers of the sc reen ‘‘x11’’.
Ta b l e  1 6 .Recommended and Available CPs in Australia — Continued
Equipment Equipment Type
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
39 Australia 
Luc ent rec ommend s only the following  c all typ es b e used  in Australia:
System Parameter Administration
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nFeature-Related System Parameters Ad ministration
— Trunk-to-Trunk Transfer: Permitted  b y c ountry’s reg ulations - 
Selec tion is c ustomer’s c hoic e.
— Pub lic  Network Trunks on Conferenc e Call: 5
— Conferenc e Parties With PNTs: 6
— Conferenc e Parties Without PNTs: 6
— Line Interc ep t Tone Timer: 30
— Nig ht Servic e Disc onnec t Timer: 180 sec
— Short Interd ig it Timer: 3 sec
— Unanswered  DID Call Timer: 60 
—Auto-Hold: Yes 
1
— Attend ant Tone: Yes
— Bridg ing  Tone: No
— Conferenc e Tone: No
— Intrusion Tone: Yes
— Rep etitive Call Waiting Tone: No
— DID Busy Treatment: Attend ant
— Pull Transfer: No
— Level of Tone Detec tion: Prec ise
— Outp ulse Without Tone: Yes
— (Station-to-switc h) Rec all Timing :
nFlashhook Interval: Yes 
nUp p er Bound : 1000 ms 
nLower Bound : 200 ms  int: For all international numb ers.
pubu: For all other types of digit strings.
1. Althoug h not a Type App roval issue, this rep resents the convention for this country. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
40 Australia 
nSystem Parameter Country Op tions Ad ministration
— Comp and ing  Mode: A-law
— Base Tone Generation Set: 2
— Tone Detec tion Mod e: 2
— Interd ig it Pause: short
— Dig ital Loss Plan: 2
— Analog Ringing Cadence: 2
Analog Trunk Administration
n CO Trunks
— Trunk Group  Sc reen
nGroup  Typ e: CO 
nCountry: 2
nTrunk Gain: hig h
nDirec tion: two-way 
nDig it Ab sorp tion List: b lank 
nPre f i x -1 :  N o
nTrunk Type: loop -start
nOutg oing  Dial Typ e: tone 
nTrunk Termination: rc  (c omp lex imp ed anc e)
nAuto Guard : yes 
nDial Acc ess: yes
nCall Still Held : yes 
nTerminal Balanc ed : yes 
nRec eive Answer Sup ervision: no 
nAnswer Supervision Timeout: 10 (This sets both the CP 
firmware timer and  software timer. Set to 0 for any trunk that 
will rec eive answer sup ervision.)
nDisc onnec t Sup ervision - In: yes
nDisc onnec t Sup ervision - Out: Selec tion is c ustomer’s 
choice.
nDisc onnec t Timing : 500 msec  (This field  will not b e used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.) 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
41 Australia 
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  CO 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 500 ms
nOutg oing  Disc onnec t: 500 ms
nOutg oing  Dial Guard : 1600 ms 
nInc oming  Glare Guard : 1500 ms 
nOutg oing  Glare Guard : 1500 ms 
nOutg oing  Dial Pulse Rate (PPS): 10 p p s
nOutg oing  Rotary Dig it Dial Make: 35 ms
nOutg oing  Rotary Dig it Dial Break: 65 ms
nOutg oing  Rotary Dial Interd igit: 800 ms
nRing  Monitor Timer: 5200 ms
nInc oming  Seizure: 500 ms
nOutg oing  End -of-Dial: 10 sec
nOutg oing  Seizure Resp onse: 240 sec
nProg rammed  Dial Pause: 1500 ms
nDisc onnec t Sig nal Error: 240 sec
nFlash Leng th: 100 ms
nPPM :  Ye s
nPPM Freq uenc y: 50/12kHz
nDID Trunks
— Trunk Group  Sc reen
nGroup  Typ e: DID
nCountry: 2
nTrunk Gain: hig h
nDig it Ab sorp tion List: b lank 
nInc oming  Dial Typ e: tone
nTrunk Type: immed -start
nTrunk Termination: rc  (c omp lex imp ed anc e)
nDisc onnec t Sup ervision - In: yes 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
42 Australia 
nDisc onnec t Timing : 500 msec  (This field  will not b e used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.)
nDig it Treatment: b lank 
nDig its: b lank 
nExp ec ted  Dig its: d ep end s on system size and  numb ering  
plan
nTerminal Balanc ed : yes 
nExtend ed  Loop  Range: (Used  Only with TN459) no 
nDrop  Treatment: silenc e 
nInc oming  Rotary Timeout (sec ): 5 sec  (This field  will not b e 
used  with CPs that c an ac c ept the Inc oming  Partial Dial 
timer. Set this timer from the Ad ministrab le Timers Sc reen.)
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  DID 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 500 ms
nInc oming  Dial Guard : 50 ms
nInc oming  Partial Dial: 18 sec
nInc oming  Inc omplete Dial: 255 sec
nFlash Leng th: 100 ms
nTi e  Tru n k s
No sp ec ial Typ e Ap p roval reg ulations ap ply. Tie trunks are ad ministered  
on a c ase-b y-c ase b asis.
Digital Trunk Administration
This sec tion d oes not list all p ossib le valid  ad ministrable c omb inations. Rather 
the most c ommon or stand ard c ombination, c omp atib le with p ub lic -network and  
Typ e Ap proval stand ard s for eac h c ountry, is p resented :
nCO and  DID Trunks
Not availab le in this c ountry.
nTi e  Tru n k s
— Non-ISDN Sig naling  Examp le (DS1 Ad ministration Sc reen)
nCirc uit Pac k: TN464D (Not entered  as ad ministrab le item; 
TN464C from up g rad es)
nBit Rate: 2.048