Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
273 Italy (Lucent Technologies) 
NOTE:
If c onnec ted  to a 20-p ps system, then set the Outgoing 
Rotary Dig it Dial Make and  Outg oing  Rotary Dig it Dial 
Break times to 20 and 30 ms resp ec tively.
nOutg oing  Rotary Dig it Dial Break: 60 ms
nOutg oing  Rotary Dial Interd igit: 700 ms
nInc oming  Seizure: 100 ms (E&M c ont)
nOutg oing  End -of-Dial: 10 sec
nOutg oing  Seizure Resp onse: 1 sec  (E&M c ont, d is)
nDisc onnec t Sig nal Error: 2 sec  (E&M c ont)
nDisc onnec t Sig nal Error: 1 sec  (E&M dis)
nInc oming  Partial Dial: 15 sec
Digital Trunk Administration
This sec tion d oes not list all p ossible valid  ad ministrab le c omb inations.Rather the 
most c ommon or stand ard  c omb ination, c omp atib le with p ub lic -network and  
Typ e Ap proval stand ard s for eac h c ountry, is p resented :
nCO Trunks
— DS1 Ad ministration Sc reen
nCirc uit Pac k: TN464F (Not entered as ad ministrab le item)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 4
nInterc onnec t: CO
nCRC?: Yes
nId le Cod e: 01010100
nTrunk Group  Ad ministration sc reen (Timing ) 
nDig ital trunk timing  values should  b e set as for analog  CO 
trunks.
nDID Trunks
— DS1 Ad ministration sc reen
nCirc uit Pac k: TN464F
nBit Rate: 2.048 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
274 Italy (Lucent Technologies) 
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 4
nInterc onnec t: CO
nCRC?: No
nId le Cod e: 01010100
— Trunk Group  Ad ministration sc reen (Timing ) 
Dig ital trunk timing  values should  b e set as for analog  DID trunks.
nTi e  Tru n k s
— Non-ISDN Sig naling  Examp le (DS1 Ad ministration sc reen)
nGroup  Typ e: tie
nCirc uit Pac k: TN464F
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 4
nInterc onnec t: p b x
nCRC?: no
nId le Cod e: 01010101
— Trunk Group  Ad ministration sc reen (Timing ) 
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  Tie 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 50 ms
nOutg oing  Disc onnec t: 50 ms
nInc oming  Dial Guard : 70 ms
nOutg oing  Dial Guard : 1000 ms
nInc oming  Glare Guard : 200 ms
nOutg oing  Glare Guard : 200 ms
nOutg oing  Dial Pulse Rate (PPS): 10 p p s
nOutg oing  Rotary Dig it Dial Make: 50 ms
nOutg oing  Rotary Dig it Dial Break: 50 ms 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
275 Italy (Lucent Technologies) 
nOutg oing  Rotary Dial Interd igit: 700 ms
nInc oming  Seizure: 100 ms
nOutg oing  Seizure Resp onse: 60 sec
nDisc onnec t Sig nal Error: 255 sec
nInc oming  Partial Dial: 6 sec
— ISDN-PRI (Private Network) Sig naling (DS1 Ad ministration sc reen)
This examp le assumes use of US Op tion 1 with fac ility assoc iated  
sig naling . Other feature op tions will req uire c hang es in one or more 
ad ministered  items. 
nCirc uit Pac k: TN464F
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: isdn-pri
nCountry Protoc ol: 4
nConnec t: p b x
nInterfac e: user
nCRC: No
nId le Cod e: 01010101
nSignaling Group screen
nAssoc iated Sig naling : Yes
nPrimary D_Channel: xxxx16 (xxxx= > dep end s on CP 
p hysical location)
— Trunk Group  Ad ministration sc reen
nGroup Type: isdn-pri
nServic e Type: tie
nISDN-PRI (Public  Network) (DS1 Ad ministration sc reen)
Temporary Sig naling  Connec tions and  D-Channel Bac kup  
features must not b e ad ministered  for E1 interfac es that use 
country protocol 13 (Italy).
nCirc uit Pac k: TN464F
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: isdn-pri 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
276 Italy (Lucent Technologies) 
nConnec t: Network
nCountry Protocol: 13
nProtoc ol Version: a, for 1TR6 and  b , for E-DSS1.
Protoc ol version selec tion d ep end s on the typ e of p ub lic  
network servic e p urc hased  by the c ustomer
nCRC: yes
nId le Cod e: 01010100
nSignaling Group screen
nAssoc iated Sig naling : Yes
nPrimary D_Channel: xxxx16 (xxxx= > dep end s on CP 
p hysical location)
— Trunk Group  Ad ministration sc reen
nGroup Type: isdn-pri
nCOR: COR for isd n-p ri p ub lic _ntwrk trunks must have a 
higher FRL than all Tie Trunks
nService Type: public_ntwrk
nOverlap  Rec eiving: yes, a must for DID trunk op eration
Station Administration
The ad ministrator c an selec t italian on station ad ministration and  attend ant 
ad ministration to pic k Italian as the d isp lay lang uage for the c orresp ond ing  
d isp lay set user.
n85XX Terminals
The 8510 terminal must b e ad ministered  as a 7507 terminal to b e ab le to 
use the 8510 terminal for b oth voic e and  d ata operation. If used  for voic e 
only op eration, a terminal typ e of 8510D is suffic ient. Aliasing  a terminal 
type of 8510+  to a 7507 is p referab le.
— Terminal Setting s:
Eac h 8510 must b e p rogramed  with the following  p arameters:
nCountry Code =  6
nComp and ing  Mode =  a-law
nTransmit Value =  + 3 
nReceive Value =  -5 
nSid e Tone Value =  0 
nUse the following  p rog ramming  seq uenc e. 
n8510 Prog ram Instruc tions: (items in b rac kets [ ] mean use 
that b utton) for setting  the p rop er c ountry c od e of 6. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
277 Italy (Lucent Technologies) 
En t e r :
                          Value    Meaning
                          ______   ______
                          [ MENU]
                          [ MUTE]
                          2           p rog ram for
                          4           setting c ountry op tion
                          6           c ountry c ode 6
                          #        save value
For setting  the p rop er transmission values for Italy (G3V3): 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
278 Italy (Lucent Technologies) 
En t e r :
Value Meaning
______ ______
[ MENU]
[MUTE] 
2           p rog ram for
5           setting  transmission values
2           a-law
#           save value and  p roc eed  to next step
3           transmit value of + 3 d esired
*           tog g le to selec t + 
#           save value and  p roc eed  to next step
5           rec eive value of -5 d esired
*           tog g le to selec t -
#           save value and  p roc eed  to next step
0           sid e tone value of 0 d esired
#  save value and  c omp lete setup  step s for b oth 
voic e and d ata op eration
The following values have been determined as a result of type approval.
n84XX (94XX) Terminals
Aliasing  the terminal typ es of 9403B to 8403B, 9410B to 8410B, 9410D to 
8410D, and  9434D to 8434D is a preferable way of hand ling  the 
ad ministration for the 94XX family of terminals.
—Terminal Parameters
nDefault Parameter Set: 4
nCustomize Parameters? n
The default p arameters for selec ting  Italy c ountry c od e 4 are 
as follows and  ARE PROGRAMMED AUTOMATICALLY. 
These values are inc lud ed  as referenc e information only.
— Display Mode: 1
— DLI Voltag e Level: auto
— Handset Exp and er Enab led ? n 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
279 Italy (Lucent Technologies) 
— Primary Levels:
nVoic e Transmit (d B): + 14.0
nVoic e Sid etone (d B): -25.0
nVoice Receive (dB): -5.0
nTouc h Tone Sid etone (d B): -25.0
nTouc h Tone Transmit (d B): -4.0
— Ad junc t Levels
nVoic e Transmit (d B): 0.0
nVoice Receive (dB): -2.0
nVoic e Sid etone (d B): -14.5
nTouc h Tone Sid etone (d B): -25.0
n603/302B Terminals (nothing exc ep t for alias of 94XX to 84XX eq uivalent)
—Terminal Parameters
nDefault Parameter Set: 4
nCustomize Parameters? n
The default p arameters for selec ting  Italy c ountry c od e 4 are 
as follows and  ARE PROGRAMMED AUTOMATICALLY with 
software load  G3V3i.02.0.044.0 or later loads. These values 
are inc lud ed  as referenc e information only.
— Display Mode: 1
— DLI Voltag e Level: auto
— Primary Levels:
nVoice Transmit (dB): + 7.0
nVoic e Sid etone (d B): -35.5
nVoice Receive (dB): -6.5
nTouc h Tone Sid etone (d B): -25.0
nTouc h Tone Transmit (d B): -4.0 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
280 Italy-Italtel 
Italy-Italtel
Ta b l e  3 8 shows the rec ommended  c irc uit p ac ks.
Table 38. Recommended and Available CPs in Italy-Italtel
Equipment Equipment Type
Cab inet Typ e & Power GAC-MCC DC-MCC AC-SCC AC-CSCC 
AC-CMC
AC Power Voltag e & Freq 220V/50Hz 
Ring  Generator 20Hz
Tone Detec tor > TN420C
Tone Cloc k > TN780 TN419B
R2MFC Circ uit n/a
Sp eec h Synthesizer > TN433 
Call Classifier > TN2182B > TN744D
Announc ement #TN750C > TN750B 
Analog DID Trunk > TN2139
Analog  CO Trunk (No PPM)  > n/a
Analog  CO Trunk (w/PPM) > TN2138
4 Wire Tie Trunk #TN2140B TN2140
2 Wire Tie Trunk > TN497
Auxiliary Trunk > TN763D TN417
Dig ital CO/DID Trunk > TN464F TN464E TN464D TN464C TN464B
Dig ital Tie Trunk > TN464F TN464E TN464D TN464C TN464B
Dig ital PRI CO Trunk n/a 
Dig ital BRI Trunk 
Dig ital Converter PRI-DASS   
Dig ital Converter PRI-DPNSS
Dig ital Converter PRI-BRI   
8 Port Analog  Line n/a
16 Port Analog  Line > TN2183 > TN2135
24 Port Analog  Line n/a
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
281 Italy-Italtel 
Feature Administration
The sc reen d isp lays shown in this sec tion were effec tive the d ate the typ e 
ap p roval was award ed . The sc reens may have c hang ed  sinc e that d ate.
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nARS/AAR Ad ministration 
To enab le ARS administration, on the System-Parameters 
Customer-Op tions sc reen, set the ARS
 field  to y
. You also should check all 
ARS/AAR d efaults. All d efault ARS analysis c odes are deleted  b efore 
d ialed  strings are ad d ed for routing when DEFINITY is installed  outsid e of 
North Americ a. Be aware that the d efault for the 10 d ig its c ause dialing 
p rob lems. In p artic ular, the following  c all typ es (ap pear as ARS/AAR 
d efaults) typ ic ally are not used  in non-North Americ an ARS/AAR tab les:
Luc ent rec ommend s only the following  c all typ es b e used  outside North 
Americ a: 4 Wire Digital Line > TN754B TN413
2 Wire Digital Line > TN2181 TN2136
Data Line > TN726B 
BRI-U
BRI-ST
fnp a: North Americ an numb ers with an area c od e.
hnp a: North Americ an numb ers without an area c od e.
svc : North Americ an numb ers of the sc reen ‘‘x11’’.
int: For all international numb ers.
natl: For all national PN numbers.
p ub u: For all other external (that is, not extensions) numb ers.
Ta b l e  3 8 .Recommended and Available CPs in Italy-Italtel — Continued
Equipment Equipment Type
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
282 Italy-Italtel 
System Parameter Administration
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nConsole Parameters Ad ministration
— Return Call Timeout (sec ): 10 sec
nFeature-Related System Parameters Ad ministration
— Trunk-to-Trunk Transfer: Permitted  b y c ountry’s reg ulations - 
Selec tion is c ustomer’s c hoic e.
— Pub lic  Network Trunks on Conferenc e Call: 5
— Conferenc e Parties With PNTs: 6
— Conferenc e Parties Without PNTs: 6
— Line Interc ep t Tone Timer: 30
— Nig ht Servic e Disc onnec t Timer: 180 sec
— Short Interd ig it Timer: 3 sec
— Unanswered  DID Call Timer: 60 
—Auto-Hold: Yes 
11
— Attend ant Tone: Yes
— Bridg ing  Tone: No
— Conferenc e Tone: No
— Intrusion Tone: Yes
— Rep etitive Call Waiting Tone: No
— DID Busy Treatment: Attend ant
— Pull Transfer: No
— Level of Tone Detec tion: Prec ise
— Outp ulse Without Tone: Yes
— (Station-to-Switc h) Rec all Timing :
nFlashhook Interval: Yes 
nUp p er Bound : 1000 ms 
nLower Bound : 200 ms 
nCountry Op tions Parameters
— Comp and ing  Mode: A-law
— Base Tone Generation Set: 4
11. Althoug h not a Type App roval issue, this rep resents the convention for this country.