Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
283 Italy-Italtel 
— Tone Detec tion Mod e: 1
— Interd ig it Pause: short
— Dig ital Loss Plan: 4
— Analog Ringing Cadence: 4
Analog Trunk Administration
nCO Trunks
— Trunk Group  Sc reen
nGroup  Typ e: CO 
nCountry: 4
nTrunk Gain: hig h
nDirec tion: two-way 
nDig it Ab sorp tion List: b lank 
nPre f i x -1 :  N o
nTrunk Type: loop -start or g round -start
nOutg oing  Dial Typ e: tone 
nTrunk Termination: rc  (c omp lex imp ed anc e)
nAuto Guard : no 
nDial Acc ess: yes
nCall Still Held : no 
nTerminal Balanc ed : yes 
nRec eive Answer Sup ervision: no 
nAnswer Supervision Timeout: 10 (This sets both the CP 
firmware timer and software timer. This should  b e set to 0 for 
any trunk that will rec eive answer sup ervision.)
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: Selec tion is c ustomer’s 
choice.
nDisc onnec t Timing : 500 ms (This field  will not be used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.)
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  CO 
trunk timer values for this c ountry: 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
284 Italy-Italtel 
nInc oming  Disc onnec t: 50 ms
nOutg oing  Disc onnec t: 50 ms
nInc oming  Dial Guard : 70 ms 
nOutg oing  Dial Guard : 1000 ms 
nInc oming  Glare Guard : 200 ms 
nOutg oing  Glare Guard : 200 ms 
nOutg oing  Dial Pulse Rate (PPS): 10 p p s
nOutg oing  Rotary Dig it Dial Make: 50 ms
nOutg oing  Rotary Dig it Dial Break: 50 ms
nOutg oing  Rotary Dial Interd igit: 700 ms
nRing  Monitor Timer: 5200 ms
nInc oming  Seizure: 500 ms
nOutg oing  End -of-Dial: 10 sec
nOutg oing  Seizure Resp onse: 60 sec
nProg rammed  Dial Pause: 1500 ms
nDisc onnec t Sig nal Error: 255 sec
nEnd -To-End  Sig naling  Tone: 350 ms (ac c ep t d efault)
nFlash Leng th: 100 ms
nPPM :  Ye s
nFreq uenc y: 12kHz
nDID Trunks
— Trunk Group  Sc reen
nGroup  Typ e: DID
nCountry: 4
nTrunk Gain: hig h
nDig it Ab sorp tion List: b lank 
nInc oming  Dial Typ e: tone
nTrunk Type: immed -start
nTrunk Termination: rc  (c omp lex imp ed anc e)
nDisc onnec t Sup ervision: no
nDisc onnec t Timing : 500 ms (This field  will not be used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.) 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
285 Italy-Italtel 
nDig it Treatment: b lank 
nDig its: b lank 
nExp ec ted  Dig its: d ep end s on system size and  numb ering  
plan
nTerminal Balanc ed : yes 
nExtend ed  Loop  Range: (Used  Only with TN459) no 
nDrop  Treatment: silenc e 
nInc oming  Rotary Timeout (sec ): 5 sec  (This field  will not b e 
used  with CPs that c an ac c ept the Inc oming  Partial Dial 
timer. Set this timer from the Ad ministrab le Timers Sc reen.)
—  Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  DID 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 500 ms
nInc oming  Dial Guard : 50 ms
nInc oming  Partial Dial: 6 sec
nInc oming  Inc omplete Dial: 255 sec
nFlash Leng th: 100 ms
nTi e  Tru n k s
The TN2140 is used  for E&M trunks that may b e ad ministered  as either 
Continuous or Disc ontinuous. This sec tion lists the only valid  
ad ministration c omb inations p ossib le for these trunks.
Use the following  ad ministration for these typ es:
— Continuous T1
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Sig naling  Typ e: c ont
nTrunk Type (in/out): c ont/c ont
nSend  Release Ac k: y
nRec eive Release Ac k: y
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Continuous T2
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Sig naling  Typ e: c ont
nTrunk Type (in/out): immed /immed 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
286 Italy-Italtel 
nSend  Release Ac k: y
nRec eive Release Ac k: y
nSend  Answer Sup ervision: y
nRec eive Answer Sup ervision: y
— Disc ontinuous T1
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nTrunk Type (in/out): immed /immed
nSend  Release Ac k: y
nRec eive Release Ac k: y
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Disc ontinuous T2
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nTrunk Type (in/out): d isc /d isc
nSend  Release Ac k: n
nRec eive Release Ac k: n
nSend  Answer Sup ervision: y
nRec eive Answer Sup ervision: y
— Disc ontinuous T3
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nTrunk Type (in/out): immed /immed
nSend  Release Ac k: n
nRec eive Release Ac k: n
nSend  Answer Sup ervision: y
nRec eive Answer Sup ervision: y
— Disc ontinuous T4
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nTrunk Type (in/out): d isc /d isc
nSend  Release Ac k: n 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
287 Italy-Italtel 
nRec eive Release Ac k: n
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Disc ontinuous T5
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Sig naling  Typ e: d is              
nTrunk Type (in/out): immed /immed
nSend  Release Ac k: n
nRec eive Release Ac k: n
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
If the TN497 is used  as tie trunk interfac e CP, set Group  Typ e 
and  Sig naling  Typ e field s as follows:
nGroup  Typ e: tie
nSig naling  Typ e: tg e, tg u or tg i
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  tie 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 300 ms (E&M c ont)
nOutg oing  Disc onnec t: 300 ms (E&M c ont)
nOutg oing  Dial Guard : 400 ms (E&M c ont, d is)
nInc oming  Glare Guard : 800 ms (E&M c ont, d is)
nOutg oing  Glare Guard : 1000 ms (E&M c ont) Outg oing  Glare 
Guard : 1200 ms (E&M d is)
nOutg oing  Dial Pulse Rate (PPS): 10 p p s
nOutg oing  Rotary Dig it Dial Make: 40 ms 12
nOutg oing  Rotary Dig it Dial Break: 60 ms
nOutg oing  Rotary Dial Interd igit: 700 ms
nInc oming  Seizure: 100 ms (E&M c ont)
nOutg oing  End -of-Dial: 10 sec
nOutg oing  Seizure Resp onse: 1 sec  (E&M c ont, d is)
12. If c onnec ted to a 20-p p s system, then set the Outg oing  Rotary Dig it Dial Make and  
Outgoing  Rotary Dig it Dial Break times to 20 and  30 ms, resp ectively. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
288 Italy-Italtel 
nDisc onnec t Sig nal Error: 2 sec  (E&M c ont) Disc onnec t Sig nal 
Error: 1 sec  (E&M d is)
nInc oming  Partial Dial: 15 sec
Digital Trunk Administration
This sec tion d oes not list all p ossib le valid  ad ministrable c omb inations. Rather 
the most c ommon or stand ard c ombination, c omp atib le with p ub lic -network and  
Typ e Ap proval stand ard s for eac h c ountry, is p resented :
nCO Trunks
— DS1 Ad ministration Sc reen
nCirc uit Pac k: TN464D (Not entered  as ad ministrab le item; 
TN464C from up g rad es)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 4
nInterc onnec t: CO
nCRC?: No
nId le Cod e: 01010100
— Trunk Group  Ad ministration Sc reen (Timing ) Dig ital trunk timing  
values should  b e set as for analog CO trunks.
nDID Trunks
— DS1 Ad ministration Sc reen
nCirc uit Pac k: TN464D (or TN464C,B)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 4
nInterc onnec t: CO
nCRC?: No
nId le Cod e: 01010100 
— Trunk Group  Ad ministration Sc reen (Timing ) Dig ital trunk timing  
values should  b e set as for analog DID trunks. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
289 Italy-Italtel 
nTi e  Tru n k s
— Non-ISDN Sig naling  Examp le (DS1 Ad ministration sc reen)
nGroup  Typ e: tie
nCirc uit Pac k: TN464D (or TN464C,B)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 4
nInterc onnec t: p b x
nCRC?: no
nId le Cod e: 01010101 
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  tie 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 50 ms
nOutg oing  Disc onnec t: 50 ms
nInc oming  Dial Guard : 70 ms
nOutg oing  Dial Guard : 1000 ms
nInc oming  Glare Guard : 200 ms
nOutg oing  Glare Guard : 200 ms
nOutg oing  Dial Pulse Rate (PPS): 10 p p s
nOutg oing  Rotary Dig it Dial Make: 50 ms
nOutg oing  Rotary Dig it Dial Break: 50 ms
nOutg oing  Rotary Dial Interd igit: 700 ms
nInc oming  Seizure: 100 ms
nOutg oing  Seizure Resp onse: 60 sec
nDisc onnec t Sig nal Error: 255 sec
nInc oming  Partial Dial: 6 sec
— ISDN-PRI (Private Network) Sig naling
This examp le assumes use of US Op tion 1 with fac ility assoc iated  
sig naling . Other feature op tions will req uire c hang es in one or more 
ad ministered  items. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
290 Italy-Italtel 
— DS1 Ad ministration sc reen
nCirc uit Pac k: TN464D (or TN464C,B from up g rad es)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: isdn-pri
nCountry Protoc ol: 4
nConnec t: p b x
nInterfac e: user 
nCRC: No
nId le Cod e: 01010101 
— Sig naling  Group  sc reen
nAssoc iated Sig naling : Yes
nPrimary D_Channel: xxxx16 (xxxx= > dep end s on CP 
p hysical location)
— Trunk Group  Ad ministration sc reen
nGroup Type: isdn-pri
nServic e Type: tie
— ISDN-PRI (Public  Network) Not available in this c ountry. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
291 Japan 
Japan
Ta b l e  3 9 shows the rec ommended  c irc uit p ac ks.
Table 39. Recommended and Available CPs in Japan
Equipment Equipment Type
Cab inet Typ e & Power GAC-MCC AC-MCC DC-MCC AC-SCC 
DC-SCC AC-CSCC AC-CMC
AC Power Voltag e & Freq 100V/50Hz 100V/60Hz 200V/50Hz 
200V/60Hz
Ring Generator 20Hz
Tone Detec tor > TN2182B > TN744D TN748D TN756
Tone Cloc k > TN2182B TN780 TN756
R2MFC Circ uit n/a
Sp eec h Synthesizer > TN725B 
Call Classifier > TN744D
Announc ement TN750C TN750B TN750
Analog  DID Trunk > TN429B
Analog  CO Trunk (No PPM)  > TN429B TN465
Analog  CO Trunk (w/PPM) n/a
4 Wire Tie Trunk > TN760D
2 Wire Tie Trunk > TN439
Auxiliary Trunk > TN763D TN763C
Dig ital CO/DID Trunk > TN464F TN464E TN464D TN464C TN767
Dig ital Tie Trunk > TN464F TN464E TN464D TN464C TN767 
TN2242
Dig ital PRI CO Trunk > TN464F TN464E TN464D TN464C TN2242
Dig ital BRI Trunk > TN2185
Dig ital Converter PRI-DASS   
Dig ital Converter PRI-DPNSS
Dig ital Converter PRI-BRI   
8 Port Analog  Line TN742
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
292 Japan 
Feature Administration
The sc reen d isp lays shown in this sec tion were effec tive the d ate the typ e 
ap p roval was award ed . The sc reens may have c hang ed  sinc e that d ate.
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nARS/AAR Ad ministration 
To enab le ARS administration, on the System-Parameters 
Customer-Op tions sc reen, set the ARS
 field  to y
. You also should check all 
ARS/AAR d efaults. All d efault ARS analysis c odes are deleted  b efore 
d ialed  strings are ad d ed for routing when DEFINITY is installed  outsid e of 
North Americ a. Be aware that the d efault for the 10 d ig its c ause dialing 
p rob lems. In p artic ular, the following  c all typ es (ap pear as ARS/AAR 
d efaults) typ ic ally are not used  in non-North Americ an ARS/AAR tab les: 16 Port Analog  Line > TN746B TN479
24 Port Analog  Line TN2793
4 Wire Digital Line > TN754B 
2 Wire Digital Line #TN2224 > TN2181 
Data Line > TN726B 
BRI-U Line
BRI-ST Line
fnp a: North Americ an numb ers with an area c od e.
hnp a: North Americ an numb ers without an area c od e.
svc : North Americ an numb ers of the sc reen ‘‘x11’’.
Ta b l e  3 9 .Recommended and Available CPs in Japan — Continued
Equipment Equipment Type
Continued on next page