Home
>
Lucent Technologies
>
Communications System
>
Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual
Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual
Have a look at the manual Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 413 Lucent Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval Issue 1
June 1999
Application Notes for Type Approval
453 Trinidad & Tobago
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): 540
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
Total Administered Members: 0
GROUP MEMBER ASSIGNMENTS
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval Issue 1
June 1999
Application Notes for Type Approval
454 Trinidad & Tobago
DIOD Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: diod CDR Reports: y
Group Name: OUTSIDE CALL COR: 94 TN: 1 TAC:
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99
Queue Length: 0 Country: 1
Auth Code? n Digit Absorption List:
Prefix-1? y Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: immed-start
Outgoing Dial Type: tone Incoming Dial Type: tone
Trunk Termination: rc
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
Page 2 of 20
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval Issue 1
June 1999
Application Notes for Type Approval
455 Trinidad & Tobago
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Incoming Dial Guard(msec): 70 Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval Issue 1
June 1999
Application Notes for Type Approval
456 Trinidad & Tobago
DID Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: did CDR Reports: y
Group Name: OUTSIDE CALL COR: 93 TN: 90 TAC:
Country: 1
Auth Code? n
TRUNK PARAMETERS
Trunk Type: immed-start Incoming Rotary Timeout(sec): 5
Incoming Dial Type: tone
Trunk Termination: rc Disconnect Timing(msec): 500
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Extended Loop Range? n Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? n
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500
Incoming Dial Guard(msec): 70
Flash Length(msec): 540 Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval Issue 1
June 1999
Application Notes for Type Approval
457 Trinidad & Tobago
DS1 for CO, DID and DIOD trunks to the PTT
using Digital
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name
1:
2:
3:
Page 1 of 1
DS1 CIRCUIT PACK
Location: Name: T-1CO, DID, DIOD
Bit Rate: 1.544 Line Coding: b8zs
Signaling Mode: Common Channel Signalling
Interconnect: CO Country Protocol: 1
Interface Companding: mulaw CRC? n
Idle Code: 11111111
MAINTENANCE PARAMETERS
Slip Detection? n Near-end CSU Type: other
DEFINITY® Enterprise Communications Server Application Notes for Type Approval Issue 1 June 1999 Application Notes for Type Approval 458 United Kingdom United Kingdom Ta b l e 6 0 shows the rec ommended c irc uit p ac ks. Table 60. Recommended and Available CPs in the United Kingdom Equipment Equipment Type Cab inet Typ e & Power GAC-MCC DC-MCC AC-SCC AC-CSCC AC-CMC AC Power Voltag e & Freq 240V/50Hz Ring Generator 25Hz Tone Detec tor > TN2182B > TN744D TN420C TN420B Tone Cloc k > TN2182B TN780 TN419B R2MFC Circ uit n/a Speech Synthesizer > TN457 Call Classifier > TN744D Announc ement TN750C TN750B Analog DID Trunk > TN459B TN459 Analog CO Trunk (No PPM) > TN2147C TN2147 Analog CO Trunk (w/PPM) > TN447 4 Wire Tie Trunk > TN760Dv12 TN458 2 Wire Tie Trunk Auxiliary Trunk > TN763D TN417 Dig ital CO/DID Trunk TN2464 TN464E TN464D Dig ital Tie Trunk TN2464 TN464E TN464D TN464C Dig ital PRI CO Trunk TN2464 TN464E TN464D Dig ital BRI Trunk > TN2185b Dig ital Converter PRI-DASS TN-CCSC-1 Dig ital Converter PRI-DPNSS TN-CCSC-2 Dig ital Converter PRI-BRI #TN-PRI-BRI 8 Port Analog Line TN467 16 Port Analog Line #TN2183 > TN468B TN468 24 Port Analog Line n/a Continued on next page
DEFINITY® Enterprise Communications Server Application Notes for Type Approval Issue 1 June 1999 Application Notes for Type Approval 459 United Kingdom Feature Administration The sc reen d isp lays shown in this sec tion were effec tive the d ate the typ e ap p roval was award ed . The sc reens may have c hang ed sinc e that d ate. Only those feature-related p arameters that may have a Typ e Ap p roval or b asic c onnec tivity imp lic ation are listed here. nARS/AAR Ad ministration To enab le ARS administration, on the System-Parameters Customer-Op tions sc reen, set the ARS field to y . You also should check all ARS/AAR d efaults. All d efault ARS analysis c odes are deleted b efore d ialed strings are ad d ed for routing when DEFINITY is installed outsid e of North Americ a. Be aware that the d efault for the 10 d ig its c ause dialing p rob lems. In p artic ular, the following c all typ es (ap pear as ARS/AAR d efaults) typ ic ally are not used in non-North Americ an ARS/AAR tab les: Luc ent rec ommend s only the following c all typ es b e used outside North Americ a: 4 Wire Digital Line > TN754B TN413 2 Wire Digital Line #TN2224 > TN2181 Data Line > TN726B BRI-U Line TN2198 BRI-ST Line TN556d fnp a: North Americ an numb ers with an area c od e. hnp a: North Americ an numb ers without an area c od e. svc : North Americ an numb ers of the screen ‘‘x11’’. int: For all international numb ers. natl: For all national PN numb ers. p ub u: For all other external (that is, not extensions) numb ers. Ta b l e 6 0 .Recommended and Available CPs in the United Kingdom — Continued Equipment Equipment Type Continued on next page
DEFINITY® Enterprise Communications Server Application Notes for Type Approval Issue 1 June 1999 Application Notes for Type Approval 460 United Kingdom System Parameter Administration Only those feature-related p arameters that may have a Typ e Ap p roval or b asic c onnec tivity imp lic ation for a p artic ular c ountry are listed here. nSystem Parameter Features Administration — Trunk-to-Trunk Transfer: Permitted b y c ountry’s reg ulations - Selec tion is c ustomer’s c hoic e. — Pub lic Network Trunks on Conferenc e Call: 5 — Conferenc e Parties With PNTs: 6 — Intrusion Tone: Yes — DID Busy Treatment: Attend ant — Level of Tone Detec tion: Prec ise — Pull Transfer: No — (Station-to-switc h) Rec all Timing : nFlashhook Interval: No nDisc onnec t Timing : 150 ms nCountry Op tions Parameters — Comp and ing Mode: A-law — Base Tone Generation Set: 10 — Tone Detec tion Mod e: 3 — Interd ig it Pause: short — Dig ital Loss Plan: 10 — Version of Dig ital Loss Plan: nWith Only V2 CPs in System: A nWith Only New (G3) CPs in System: B nWith New & V2 CPs Mixed in System: B — Analog Ring ing Cad enc e: 10 Analog Trunk Administration nCO Trunks — Trunk Group Sc reen nCountry: 10 nTrunk Gain: hig h nGroup Typ e: CO nDirec tion: two-way
DEFINITY® Enterprise Communications Server Application Notes for Type Approval Issue 1 June 1999 Application Notes for Type Approval 461 United Kingdom nDig it Ab sorp tion List: b lank nPre f i x -1 : N o nTr u n k Ty p e : — loop -start (for Loop -Calling , Guard ed Clearing ) — ground-start (for Earth Calling) nOutg oing Dial Typ e: tone nTrunk Termination: rc (c omp lex imp ed anc e) nAuto Guard : no nDial Acc ess: yes nCall Still Held : no nTerminal Balanc ed : yes nRec eive Answer Sup ervision: no nAnswer Supervision Timeout: 10 (This sets both the CP firmware timer and software timer. Set to 0 for any trunk that will rec eive answer sup ervision.) nDisc onnec t Sup ervision - In: — no (for LCGC Trunks) — yes (for Earth Calling Trunks) nDisc onnec t Sup ervision - Out: Selec tion is c ustomer’s choice. nDisc onnec t Timing : 500 msec (This field will not b e used with CPs that c an ac c ep t the Inc oming Disc onnec t and Outg oing Disc onnec t timers. Set these latter two timers from the Ad ministrab le Timers Sc reen.) — Trunk Group Ad ministration Sc reen (Timing ) Set the following timers from the Administrab le Timers sc reen d uring ad ministration of eac h trunk g roup . Selec t the following CO trunk timer values for this c ountry: nInc oming Disc onnec t: 500 ms nOutg oing Disc onnec t: 500 ms nOutg oing Dial Guard : 1600 ms nInc oming Glare Guard : 1500 ms nOutg oing Glare Guard : 1500 ms nOutg oing Dial Pulse Rate (PPS): 10 p p s nOutg oing Rotary Dig it Dial Make: 35 ms nOutg oing Rotary Dig it Dial Break: 65 ms
DEFINITY® Enterprise Communications Server Application Notes for Type Approval Issue 1 June 1999 Application Notes for Type Approval 462 United Kingdom nOutg oing Rotary Dial Interd igit: 800 ms nRing Monitor Timer: 5200 ms nInc oming Seizure: 250 ms nOutg oing End -of-Dial: 10 sec nOutg oing Seizure Resp onse: 240 sec nProg rammed Dial Pause: 1500 ms nDisc onnec t Sig nal Error: 240 sec nEnd -To-End Sig naling Pause: 150 ms (ac c ep t d efault) nEnd -To-End Sig naling Tone: 350 ms (ac c ep t d efault) nFlash Leng th: 100 ms nPPM : y e s nFreq uenc y: 50 Hz — PPM The PPM freq uenc y monitored will d ep end up on the p artic ular CO trunk CP b eing used (a CP c ap ab le of monitoring the req uired freq uenc y must b e p rovid ed . Some trunk CPs do not sup p ort any PPM monitoring.) For this c ountry, the CP used for PPM monitoring must d etec t 50Hz p ulses. n DID Trunks — Trunk Group Sc reen nGroup Typ e: DID nCountry: 10 nGain: hig h nDig it Ab sorp tion List: b lank nInc oming Dial Typ e: tone nTrunk Type: immed -start nTrunk Termination: rc (c omp lex imp ed anc e) nDisc onnec t Timing : 500 msec (This field will not b e used with CPs that c an ac c ep t the Inc oming Disc onnec t and Outg oing Disc onnec t timers. Set these latter two timers from the Ad ministrab le Timers Sc reen.) nDig it Treatment: b lank nDig its: b lank nExp ec ted Dig its: d ep end s on system size and numb ering plan nTerminal Balanc ed : yes