Lucent Technologies DEFINITY Enterprise Communications Server Application Notes For Type Approval Manual

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
233 Hungary 
Hungary
Ta b l e  3 3 shows the rec ommended  c irc uit p ac ks.
Table 33. Recommended and Available CPs in Hungary
Equipment Equipment Type
Cab inet Typ e & Power GAC-MCC DC-MCC AC-SCC AC-CSCC 
AC-CMC
AC Power Voltag e & Freq 220V/50Hz 
Ring  Generator 20Hz
Tone Detec tor > TN2182B > TN744D TN748D TN748C
Tone Cloc k > TN2182B TN780 TN756
R2MFC Circ uit > TN744D TN744B
Sp eec h Synthesizer > TN725B 
Call Classifier > TN744D
Announc ement TN750C TN750B 
Analog DID Trunk > TN753
Analog  CO Trunk (No PPM)  > TN747B
Analog  CO Trunk (w/PPM) #TN465C > TN465B 
4 Wire Tie Trunk > TN760D > TN2140B
2 Wire Tie Trunk
Auxiliary Trunk > TN763D 
Dig ital CO/DID Trunk > TN464F TN464E TN464D
Dig ital Tie Trunk > TN464F TN464E TN464D
Dig ital PRI CO Trunk n/a 
Dig ital BRI Trunk  > TN2185
Dig ital Converter PRI-DASS   
Dig ital Converter PRI-DPNSS
Dig ital Converter PRI-BRI   
8 Port Analog  Line TN742
16 Port Analog  Line > TN746B
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
234 Hungary 
NOTE:
A-law c ompand ing  is the national stand ard  in Hung ary. However, 
Mu-law is used  internally to the system for servic e c irc uits and  
analog  lines. Network interfac es are c onfig ured  as A-law if req uired .
Country-Specific Feature
You c an use DEFINITY ECS in the Hung arian Private Network. With the 
ad ministration spec ified in this sec tion, the following  are availab le:
nOverlap  send ing
nGroup  II p ermissions c hec king
nPub lic and  Private Network interworking
nLimit on resed  req uests
nI.15 transit sig naling
Refer to Hungarian Private Network Administration on page 244
 for more 
information.
Feature Administration
The sc reen d isp lays shown in this sec tion were effec tive the d ate the typ e 
ap p roval was award ed . The sc reens may have c hang ed  sinc e that d ate.
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nARS/AAR Ad ministration 24 Port Analog  Line n/a
4 Wire Digital Line > TN754B 
2 Wire Digital Line #TN2224 > TN2181 TN2136
Data Line > TN726B
BRI-U Line
BRI-ST Line
Ta b l e  3 3 .Recommended and Available CPs in Hungary — Continued
Equipment Equipment Type
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
235 Hungary 
To enab le ARS administration, on the System-Parameters 
Customer-Op tions sc reen, set the ARS
 field  to y
. You also should check all 
ARS/AAR d efaults. All d efault ARS analysis c odes are deleted  b efore 
d ialed  strings are ad d ed for routing when DEFINITY is installed  outsid e of 
North Americ a. Be aware that the d efault for the 10 d ig its c ause dialing 
p rob lems. In p artic ular, the following  c all typ es (ap pear as ARS/AAR 
d efaults) typ ic ally are not used  in non-North Americ an ARS/AAR tab les:
Luc ent rec ommend s only the following  c all typ es b e used  outside North 
Americ a:
System Parameter Administration
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nFeature-Related System Parameters Ad ministration
— Trunk-to-Trunk Transfer: Permitted  b y c ountry’s reg ulations - 
Selec tion is c ustomer’s c hoic e.
— Pub lic  Network Trunks on Conferenc e Call: 5
— Conferenc e Parties With PNTs: 6
— Conferenc e Parties Without PNTs: 6
— Line Interc ep t Tone Timer: 30
— Nig ht Servic e Disc onnec t Timer: 180 sec
— Short Interd ig it Timer: 3 sec
— Unanswered  DID Call Timer: 60 
—Auto-Hold: Yes 
9
— Attend ant Tone: Yes
— Bridg ing  Tone: No fnp a: North Americ an numb ers with an area c od e.
hnp a: North Americ an numb ers without an area c od e.
svc : North Americ an numb ers of the sc reen ‘‘x11’’.
int: For all international numb ers.
natl: For all national PN numbers.
p ub u: For all other external (that is, not extensions) numb ers.
9. Althoug h not a Type App roval issue, this rep resents the convention for this country. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
236 Hungary 
— Conferenc e Tone: No
— Intrusion Tone: Yes
— Rep etitive Call Waiting Tone: No
— DID Busy Treatment: Attend ant
— Pull Transfer: No
— Level of Tone Detec tion: Med ium
— Outp ulse Without Tone: Yes
— (Station-to-switc h) Rec all Timing :
nFlashhook Interval: No 
nDisc onnec t Timing : 350 ms
nSystem Parameter Country Op tions Ad ministration
— Comp and ing  Mode: A-law
NOTE:
Comp and ing  Mod e: A-law is the national stand ard . Mu-law is 
used  internal to the system for servic e c irc uits and  analog  
lines. Network interfac es are c onfig ured  as A-law if req uired .
— Base Tone Generation Set: 
— Tone Detec tion Mod e: 2
— Interd ig it Pause: short
— Dig ital Loss Plan: 
— Analog Ringing Cadence: 
Analog Trunk Administration
nCO Trunks
— Trunk Group  Sc reen
nGroup  Typ e: CO 
nCountry: 
nTrunk Gain: hig h
nDirec tion: two-way 
nDig it Ab sorp tion List: b lank 
nPre f i x -1 :  N o
nTrunk Type: loop -start 
nOutg oing  Dial Typ e: tone 
nTrunk Termination: 600 ohm 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
237 Hungary 
nAuto Guard : no 
nDial Ac c ess: Yes
nCall Still Held : no 
nTerminal Balanc ed : yes 
nRec eive Answer Sup ervision: no 
nAnswer Supervision Timeout: 10 (This sets both the CP 
firmware timer and  software timer. Set to 0 for any trunk that 
will rec eive answer sup ervision.)
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: Selec tion is c ustomer’s 
choice.
nDisc onnec t Timing : 100 ms (This field  will not be used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.)
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  CO 
trunk timer values for this c ountry:
nInc oming  Glare Guard : 1500 ms 
nOutg oing  Glare Guard : 1500 ms 
nOutg oing  Rotary Dig it Dial Make: 40 ms
nOutg oing  Rotary Dig it Dial Break: 60 ms
nOutg oing  Rotary Dial Interd igit: 800 ms
nDID Trunks
— Trunk Group  Sc reen
nGroup  Typ e: DID
nCountry: 
nTrunk Gain: hig h
nDig it Ab sorp tion List: b lank 
nInc oming  Dial Typ e: tone
nTrunk Type: immed -start
nTrunk Termination: rc  (c omp lex imp ed anc e)
nDisc onnec t Sup ervision: no 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
238 Hungary 
nDisc onnec t Timing : 500 ms (This field  will not be used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.)
nDig it Treatment: b lank 
nDig its: b lank 
nExp ec ted  Dig its: d ep end s on system size and  numb ering  
Pla n
nTerminal Balanc ed : yes 
nExtend ed  Loop  Range: (Used  Only with TN459) no 
nDrop  Treatment: silenc e 
nInc oming  Rotary Timeout (sec ): 5 sec  (This field  will not b e 
used  with CPs that c an ac c ept the Inc oming  Partial Dial 
timer. Set this timer from the Ad ministrab le Timers Sc reen.)
— Trunk Group  Ad ministration Sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  DID 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 100 ms
nInc oming  Dial Guard : 10 ms
nInc oming  Partial Dial: 18 sec
nInc oming  Inc omplete Dial: 255 sec
nTie Trunks (Disc ontinuous MOL)
— Group  Typ e: tie, tand em, ac c ess, ap lt, or rlt
— Trunk Signaling Type: dis
— Direc tion: Two-way
— Dial Ac c ess: Yes
— Trunk Type: Immed /Immed
— Disc onnec t sup ervision - In:Y Out: Y
— Send  Release Ac k: Yes
— Rec eive Release Ac k: Yes
— Send  Answer Sup ervision: Yes
— Rec eive Answer Sup ervision: Yes
Set the following  are the ad ministrab le timer values:
nOutg oing  Dial Guard : 1600 ms
nInc oming  Glare Guard : 5000 ms 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
239 Hungary 
nOutg oing  Glare Guard : 5000 ms
nOutg oing  End -of-Dial: 10 sec
nOutg oing  Seizure Resp onse: 5 sec :
nDisc onnec t Sig nal Error: 90 sec
nInc oming  Partial Dial: 15 sec  (FW d efault, c annot b e 
ad ministered )
nRelease Ac k Send: 600 ms
nAnswer Send : 150 ms (if SW still limits to 120ms, FW will 
c hang e to 150ms if Hung arian MOL)
nOutg oing  Disc onnec t Send : 600 ms
nInc oming  d isc onnec t Send : 600 ms
nNormal Outg oing  Seize Send : 150 ms
Digital Trunk Administration
This sec tion d oes not list all p ossib le valid  ad ministrable c omb inations. Rather 
the most c ommon or stand ard c ombination, c omp atib le with p ub lic -network and  
Typ e Ap proval stand ard s for eac h c ountry, is p resented :
nCO Trunks
— DS1 Ad ministration Sc reen 
10
nCirc uit Pac k: TN464D (not entered as an ad ministrab le item)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 8
nInterc onnec t: CO
nCRC?: No
nId le Cod e: 01010100 
— Trunk Group  Ad ministration Sc reen (Timing )
Dig ital trunk timing  values should  b e set as for analog  CO trunks.
nDID Trunks
— DS1 Ad ministration Sc reen
nCirc uit Pac k: TN464D (not entered as an ad ministrab le item)
10. DS1 is also analog ous to the term E1 that has b een c oined  for the European T1 or 2 mb it 
interfac e. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
240 Hungary 
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 8
nInterc onnec t: CO
nCRC?: No
nId le Cod e: 01010100 
— Trunk Group  Ad ministration Sc reen (Timing )
Dig ital trunk timing  values should  b e set as for analog  DID trunks.
nTi e  Tru n k s
— Non-ISDN Sig naling  Examp le (DS1 Ad ministration Sc reen)
nCirc uit Pac k: TN464D (Not entered  as ad ministrab le item; 
TN464C from up g rad es)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: CAS
nCountry Protoc ol: 
nInterc onnec t: p b x
nCRC?: no
nId le Cod e: 01010100 
— ISDN-PRI (Private Network) Sig naling
This examp le assumes use of US Op tion 1 with fac ility assoc iated  
sig naling . Other feature op tions will req uire c hang es in one or more 
ad ministered  items.
— DS1 Ad ministration sc reen
nCirc uit Pac k: TN464D (or TN464C from up g rad es)
nBit Rate: 2.048
nInterfac e Comp anding : A-law
nLine Cod ing: HDB3
nSignaling Mode: isdn-pri
nCountry Protoc ol: 8
nConnec t: p b x 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
241 Hungary 
nInterfac e: user 
nCRC: No
nId le Cod e: 01010100 
— Sig naling  Group  sc reen
nAssoc iated Sig naling : Yes
nPrimary D_Channel: xxxx16 (xxxx= > dep end s on CP 
p hysical location)
— Trunk Group  Ad ministration sc reen
nGroup Type: isdn-pri
nService Type: public_ntwrk
— ISDN-PRI (Public  Network) Not available for this c ountry.
MFC Signaling
Ad d itional MFC sig nals c an b e used  in Hung ary.
nThe MFC sig nal end -of-d ig its and  the symb ol * in the route p attern.
When the symbol * is translated  in the route p attern and  the signal 
end-of-d ial is translated on the multi-frequenc y sc reen, the MFC tone for 
the end -of-d ig its is sent out to the CO in the plac e of the symb ol *.
nThe MFC sig nal ANI-avail.
When the MFC sig nal ANI-avail is translated  on the mutli-freq uenc y 
sc reen, the MFC tone for the ANI-avail sig nal is sent after the g roup II 
c ateg ory sig nal in the ANI d ig it response on an outg oing  c all. On an 
inc oming  c all, the MFC sig nal ANI-avail is translated, then the ANI d ig its 
are req uested  on the resp onse of the MFC tone for the ANI-avail sig nal.
Incoming Only
change system-parameters multifrequency-signaling        Page  1 of  2
       MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
                      Incoming Call Type: group-ii-mfc
                      Outgoing Call Type: none
                    Maintenance Call Type: none
                     Test Call Extension:
                    Interdigit Timer (sec): 10
    Multifrequency Signaling Incoming Intercept Treatment? y
               Received Signal Gain(-Loss) (dB): 0
             Transmitted Signal Gain(-Loss) (dB): -3 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
242 Hungary 
Tw o  Wa y
change system-parameters multifrequency-signaling        Page  2 of  2
       MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
 INCOMING FORWARD SIGNAL TYPES      INCOMING BACKWARD SIGNAL TYPES
 (Tones from CO)                         (Tones to CO)
       Group-I             Group-II            Group-A             Group-B
  11: ignored          1: normal 1 : next-digit      1 : busy
  12: ignored          2: normal 3 : end-of-dial     2 : congestion
  13: ignored          3: maint-call : 4 : free
  14: ignored          4: normal : 7 : intercept
15: ignored 5: normal : :
                       6: data-call : :
                       7: normal            :                   :
                       8: normal            :                   :
                       9: normal            :                   :
                      10: normal            :                   :
                      11: normal            :                   :
                      12: normal            :                   :
                      13: normal            :                   :
                      14: normal            :                   :
                      15: normal            :                   :
change system-parameters multifrequency-signaling        Page  1 of  3
       MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
                      Incoming Call Type: group-ii-mfc
                      Outgoing Call Type: group-ii-mfc
                    Maintenance Call Type: none
                     Test Call Extension:
                    Interdigit Timer (sec): 10
         Outgoing Forward Signal Present Timer (sec): 15
          Outgoing Forward Signal Absent Timer (sec): 30
    Multifrequency Signaling Incoming Intercept Treatment? y
               Received Signal Gain(-Loss) (dB): 0
             Transmitted Signal Gain(-Loss) (dB): -3
                          ANI Prefix:
                         ANI for PBX:
                        Next ANI Digit: send-ani
              Collect All Digits Before Seizure? n