Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Upgrades And Additions Manual

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-9 Upgrade to Release 8si 
2
Install TDM/LAN Bus Terminators
1. Verity that the two AHF110 TDM/LAN bus terminators are installed per 
Figure 2-1
.
Figure 2-1. Location of TDM/LAN Bus Terminators
Swing Existing System into Maintenance Position
1. While lifting on the left side of the existing cabinet, allow the left side to 
swing outward and to the right.
Check Health of SPE
Ty p e  status system 1 and press En te r to check the health of the system.  Figure Notes:
1. Rear of Control Cabinet
2. TDM/LAN Bus Terminator in Slot 223. TDM/LAN Bus Terminator in Slot 02
2221 00010203 04 05 06 07 08
09 10 11 12 13 14 15 16 17 18 19 20
23
scdf01a CJL 081396 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-10 Upgrade to Release 8si 
2
Disable Scheduled Maintenance and Alarm 
Origination to INADS
1. Type change system-parameters maintenance and press En te r to prevent 
scheduled daily maintenance from interfering with the update or upgrade.
2. If scheduled maintenance has begun, set the Stop Time field to 1 minute 
after the current time.
or
If scheduled maintenance has not begun, set the Start Time field to a 
time after the upgrade is completed. For example, if you start the upgrade 
at 8:00 p.m. and the upgrade takes 90 minutes, set the Start Time field 
to 21:30.
!CAUTION:
If you do not disable Alarm Origination, the system may generate 
alarms, resulting in unnecessary trouble tickets.
3. Type neither in the Alarm Origination to OSS Numbers field and 
press 
En t e r .
NOTE:
For some software loads, set the Cleared Alarm Notification 
and Restart Notification fields to disable before pressing 
En t e r.
Disable TTI
NOTE:
Do this step only if the Terminal Translation Initialization (TTI) is disabled and you want 
it enabled.
!CAUTION:
If you do not disable the TTI, the translations can be corrupted.
1. Type change system-parameters features and press 
En te r. 
2. On the second screen, set the TTI Enable? field to n to de-activate the 
TTI feature.
Check TTI Status 
1. Type status tti and press En te r. Wait until the Percent Complete field 
shows 100%. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-11 Upgrade to Release 8si 
2
Check Link Status
This optional step is to make sure the settings are the same after the upgrade.
1. Type display communication-interface links and press 
En t e r. Write down 
all enabled links.
2. Type status link 
number and press En t e r for each enabled link.
3. Write down which links are in service. 
Save Translations 
1. Type save translation and press En t e r to write all translation information 
from memory to the original translation flashcard, which takes about 10 
minutes.
When the save translations command is successful, the error code must be 
a zero; otherwise, the translations are not copied. If the translations were 
corrupted, the following error message displays when logging in:
!WARNING:
Translation corruption detected; call Lucent Technologies distributor 
immediately.
NOTE:
The save translation command cannot function if the translation 
corruption message appears. Refer to ‘‘Translation Corruption 
Detected’’ on page B-5 to clear the problem.
NOTE:
This translation card may or not be used in the remainder of the upgrade procedure, 
depending on the outcome of the Remove ISDN Interface Links step. This card is 
referred to as the original translation card.
Remove ISDN Interface Links
NOTE:
ISDN-PRI resides on the new TN794 (NetCon) circuit pack in R7si and later 
releases. It is no longer on the processor interface circuit pack.
The translations are the same as those in pre-R7 when a packet control 
circuit pack was used and the System Parameters Customer Options 
field had the PACCON field set to yes. That field was removed with the R7 or 
later upgrade.
1. Type display communication-interface 
links and press En t e r. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-12 Upgrade to Release 8si 
2
2. Write down all BX.25 links. This information is used in the ‘‘Move Circuit 
Packs from G3vs System to R8si’’ section. 
3. Write down all ISDN links. If you found no ISDN links, go to ‘‘Save 
Announcements (if necessary)’’.
4. For each link where the Prot field is set to ISDN, record the information in 
all fields (in case you need to back out of the upgrade). 
5. For each ISDN link, type busyout link 
link number and press En te r.
6. Type change communication-interface links and press 
En t e r.
7. For each link where the Prot field is set to ISDN, set the Enable field to n 
and press 
En t e r.
8. Type display communication-interface processor-channels and press 
En t e r.
9. For each processor channel where the Application field is set to ISDN, 
record the information in all fields (in case you need to back out of the 
upgrade). 
10. Type change communication-interface processor-channels and press 
En t e r.
11. For each processor channel where the Application field is set to ISDN, 
clear all fields and press 
En t e r.
12. Type change communication-interface links and press 
En t e r.
13. For 
each PI extension where the Prot field is set to ISDN:
a. Set the Est Conn field to n.
b. Set the Prot field to bx25.
c. Set the DTE/DCE field to dte.
d. Leave the Identification field blank and press 
En te r.
14. For 
each PI extension where the Prot field was set to ISDN:
a. Type display data-module 
PI Ext number and press En t e r.
b. Record the information in each field (in case you need to back out of 
the upgrade).
c. Type remove data-module 
PI Ext number and press En te r.
15. Insert the new translation card, which is formatted for use with Release 5 
or later.
16. Type save translation and press 
En t e r. Save this card for rebooting after 
you install the new hardware.
NOTE:
In this case, the original translation card is not be used for the 
remainder of the upgrade procedure. The original translation card is 
used only if you need to back out of the upgrade. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-13 Upgrade to Release 8si 
2
Save Announcements (if necessary)
NOTE:
The TN750C Announcement circuit pack stores announcements in 
nonvolatile memory; saving the announcements is optional.
1. If the PPN contains a TN750/B Announcement circuit pack, type display 
announcements and press 
En t e r.
2. If administered recorded announcements are listed, type save 
announcements 
cabinet carrier slot and press En te r. For example, 
01
D03. This takes about 30 minutes.
NOTE:
For some software loads, type save announcements from cabinet 
carrier slot
. Type help and press En t e r for a list of correct commands.
Verify Software Version
If standard reliability:
1. Type list configuration software-version and press 
En t e r. Under the 
UPDATE FILE column, note whether any patches have been applied.
NOTE:
If you restore the system to the old software, you must download 
these patches onto the system.
If high or critical reliability:
1. Type list configuration software-version long and press 
En t e r.
Shut Down DEFINITY LAN Gateway System
!WA R N I N G :
Neglecting to shut down the LAN Gateway assembly before powering down the system 
cabinet where it resides can damage the LAN Gateway disk.
1. Log onto the DEFINITY LAN Gateway.
2. On the main menu, select Maintenance > Reset System > Shutdown. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-14 Upgrade to Release 8si 
2
Shut Down DEFINITY AUDIX System
!WA R N I N G :
Neglecting to shut down the AUDIX assembly before powering down the system 
cabinet where it resides can damage the AUDIX disk.
1. Shut down the AUDIX assembly and allow the disk to completely spin 
down. Refer to ‘‘DEFINITY AUDIX Power Procedures’’ on page 1-26
.
Power Down Existing System
!CAUTION:
Powering down the control cabinet causes important system data, such as BCMS data, 
records of queued ACD calls, Automatic Wakeup request, and Do Not Disturb requests, 
to be lost. 
1. Behind the G3vs cabinet, set the circuit breaker to OFF. See Figure 2-2
. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-15 Upgrade to Release 8si 
2
Figure 2-2. Rear of G3vs System Cabinet
Remove Ground Connections
1. Remove the 6 AWG (#40) (16 mm2) ground wire from the ground block on 
the rear of the G3vs system. This wire later attaches to the new control 
cabinet.
2. Remove the 10 AWG (#25) (6 mm
2) Coupled Bonding Conductor (CBC) 
wire from the ground block on the rear of the G3vs system. This wire later 
attaches to the new control cabinet. Figure Notes
1. 10 AWG (#25) (6 mm
2) Wire to 
Coupled Bonding Conductor (CBC)
2. Backplane Connectors 1-4
3. Backplane Connectors 5-10
4. TERM Connector5. 6 AWG (#40) (16 mm2) Wire to 
Approved Ground
6. AC Power Receptacle
7. Ground Block
8. Circuit Breaker
10
94
83
72
61
5AUX
PI DCE TERM
120/240 V
60/50~
6/3A
3
2
scdf CJL 102596 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-16 Upgrade to Release 8si 
2
Move 25-Pair Cables from G3vs System to R8si 
1. Remove any reusable 25-pair cables from the rear of the G3vs system. 
NOTE:
The distance from the wall-mount G3vs system and the Release 8si 
system may require that all cables be replaced with longer cables.
2. Attach any reusable 25-pair cables to the required connectors on the rear 
of the Release 8si system.
3. Attach any 
new 25-pair cables to the required connectors on the rear of the 
Release 8si system. Route the new cables to the MDF and attach.
Move Management Terminal Cable from G3vs 
System to R8si
1. Remove the management terminal cable from the rear of the G3vs system.
2. Attach the management terminal cable to the rear of the Release 8si 
system.
Move Circuit Packs from G3vs System to R8si
1. Label each port circuit pack in the G3vs system with its slot number.
2. Remove all circuit packs from the G3vs system. Store the circuit packs in 
the static-proof packaging. 
3. Remove and retain all circuit pack blanks.
4. Install the power unit and the remaining control circuit packs into the new 
control cabinet. See Table 2-4
. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-17 Upgrade to Release 8si 
2
NOTE:
A TN2182 Tone-Cloc k c an rep lac e the TN756 Tone-Detec tor/ 
Generator. If a TN2182 is used , a TN748B Tone-Detec tor is not 
req uired .
5. Install the port circuit packs into the control cabinet. Since the new control 
cabinet has more port slots than the G3vs cabinet, there should not be a 
need to retranslate these circuit packs.
6. Install blank faceplates in any vacated slots.
7. Check the load number on the TN790B Processor label. Insert the 
appropriate flashcard into the TN794 Network Control/Packet Interface 
based on the following parameters:
nIf the load number is the Release 8 load number, insert the new or 
original translation card as directed in the Save Translation step and 
Remove ISDN Interface Links step.
nIf the load number is not the Release 8 load number, insert the 
orange-labeled software memory card.
Table 2-4. Circuit Packs for R8si
Circuit Pack Name New or Used
TN790B Processor New
TN794 Network Control/Packet 
InterfaceNew
TN765 Processor Interface 
1
1. Only if BX.25 was administered.
Reuse the circuit pack from G3vs 
system
TN780 Tone-Clock/Generator Reuse the circuit pack from G3vs 
system
Other port circuit 
packsVarious Reuse the circuit packs from G3vs 
system 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R5vs/R6vs to R8si 
2-18 Upgrade to Release 8si 
2
Connect Control Cabinet Power and Ground
1. Connect a 6 AWG (#40) (16 mm2) wire (previously used on the G3vs 
cabinet) from the single-point ground block on the control cabinet to the 
approved ground. See Figure 2-3
. 
Figure 2-3. Typical AC Power and Ground Layout 
2. Connect a 10 AWG (#25) (6 mm
2) wire (previously used on the G3vs 
cabinet) between the cabinet single-point ground block and the CBC.
3. Connect the supplied cabinet AC power cord to the AC receptacle on the 
rear of the control cabinet. Plug the opposite end of the cord into the 
dedicated electrical outlet. Figure Notes
1.  Control Cabinet 
2. Circuit Breaker
3. AC Power Receptacle
4. Single-Point Ground Block
5. 8-ft (2.5-m) Power Cord6. NEMA 5-15 or 5-20 Receptacle or 
Equivalent
7. 6 AWG (16 mm
2) Cabinet Ground 
Wire to Approved Ground
8. 10 AWG (6 mm
2) Wire to CBC
3
4
5
1
8
2
7
On
OffOn
Off
6r781851bCJL030896