Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Upgrades And Additions Manual

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-67 Add IP Interface Assembly 
6
5. When done, click OK, OK.
Upgrade to TN802B (R8)
NOTE:
The upgrade takes about 20 minutes.
1. Insert the flash disk into the right most slot on the TN802 IP trunk. On the 
monitor, a dialog box assigns a drive letter with the removable media 
designation; the default is D:. 
2. Right click on Start > Explore to open the Windows NT Exploring pane 
and select the drive letter indicated in step 1.
3. Double-click on Medpro and select the Setup icon. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-68 Add IP Interface Assembly 
6
4. Follow the Install Shield procedure to transfer all the necessary files to the 
TN802 IP Interface. 
NOTE:
In the Finish dialog box, select I will restart later. Do not 
select Restart computer.
This would be a good time to read the Readme.txt file.
5. Click on Start > Settings > Control Panel > Services.
6. Select IP Trunk and click on Startup.
NOTE:
Do not click on Start.
7. Under Startup Type, select Disabled and click OK to disable IP Trunk 
mode.
NOTE:
If IP trunk and MedPro services are both set to automatic, the 
TN802B defaults to IP Trunk and MedPro features cannot be used.
8. Select MedPro and click on Startup.
NOTE:
Do not click on Start.
9. Under Startup Type, select Automatic and click OK to enable MedPro 
mode.
10. Click Start > Shut Down and select Restart the computer?
or on the TN802:
Press the recessed reset button on the faceplate (see Figure 6-21
) until the 
LCD shows a flashing MSHUT *. When the flashing stops and the asterisk 
disappears (about 2 min), reseat the circuit pack to restart the system.
or on the SAT:
a. Type busyout board 
UUCSS and press En t e r .
b. Type reset board 
UUCSS and press En t e r. 
c. Type release board 
UUCSS and press En t e r.  
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-69 Add IP Interface Assembly 
6
Once the system is completely initialized, the LCD reads MEDPRO *.
!WARNING:
When connected remotely via pcANYWHERE, only use the 
pcANYWHERE Restart Host Computer button on the toolbar to 
restart Windows NT.
11. Affix the new TN802B label to the circuit pack.
12. Disconnect the monitor, keyboard, and mouse.
Circuit Pack Verification
1. Type change circuit-pack and press En t e r.
2. Check the Code column to see if it says DSMAPD or MedPro.
.
3. To correct it, go to the entry just above the TN802B that says DSMAPD.
4. Type MEDPRO, and press 
En te r. Changing the one entry automatically 
changes the entry above it. If it is in IP Trunk mode, you get the following 
error message:
MedPro type requires TN802 with application. Type 
MEDPRO on circuit-packs form.
5. To complete the administration, refer to the 
DEFINITY ECS Release 8 
Network Connectivity
 book.
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
11: MEDPRO RESERVED-IP
01: TN754  DIGITAL LINE  12: MEDPRO  RESERVED-IP
02: TN758  POOLED MODEM  13: TN802  B  MAPD BOARD
03: TN2144  ANALOG LINE  14: 
04: TN746  B  ANALOG LINE  15: 
05 16:         
06: TN771  C  MAINTENANCE/TEST  
07: TN464  F  DS1 INTERFACE     
08: TN2140  E&M TIE TRUNK     
09: TN767  E  DS1 INTERFACE     
10: TN799  B  CONTROL-LAN       
  # indicates circuit pack conflict. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-70 Add TTC Japanese 2-Mbit Trunks 
6
Add TTC Japanese 2-Mbit Trunks
The TN2242 Japan 2-Mbit trunk interconnects DEFINITY to other vendor 
equipment in Japan as well as to other DEFINITY switches through the Time 
Division Multiplexor (TDM).
Installing the trunks 
Determine the port assignment of the trunk from the Trunk Group form.
1. Install a TN2242 circuit pack in assigned carrier slot.
2. Connect the H600-513 cable from the DEFINITY cabinet to the Time 
Division Multiplexor device.
3. To administer forms, see the following sections in the 
DEFINITY Enterprise 
Communications Server Release 8 Administrator’s Guide
.
nFor ISDN applications, see ISDN Service.
nFor non-ISDN applications, see Managing Trunks.
Adding SCC Port Cabinets
Up to 3 port cabinets may be stacked on a Release 8si PPN’s basic control 
cabinet or EPN’s expansion control cabinet.
!CAUTION:
A port cabinet may weigh as much as 125 pounds. Use lifting precautions to 
avoid injury.
Unpack and Inspect for Damage
1. Unpack the cabinets.
2. Inspect the cabinets for any damage caused during shipping. Repor t any 
damage per local procedures.
Service Interruption
1. Since the addition of port cabinets requires a service interruption, notify the 
customer in advance when the addition will take place. EXAMPLE:3A0701
Cabinet (Port 
Network)Carrier Slot 
NumberPort 
Number 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-71 Adding SCC Port Cabinets 
6
Disable Alarm Origination
1. Type change system-parameters maintenance and press En te r.
2. Set the 
Alarm Origination field to n.
!CAUTION:
If you do not disable Alarm Origination, the system may generate 
alarms, resulting in unnecessary trouble tickets.
3. For some releases of software, disable Cleared Alarm Notification and 
Restart Notification before submitting the form.
Save Translations and Announcements
1. If the system is high or critical reliability, type status system 1 and press 
En t e r to verify that the system is in the “active” mode.
2. Type save translation and press 
En te r. This instructs the system to take all 
translation information in memory and write it to the translation cards.
3. If the SCC port network contains a 
TN750/B/C Announcement circuit pack, 
type display announcements and press 
En t e r.
4. If administered recorded announcements are listed, type list 
configuration software-version and press 
En t e r. To save the 
announcements, type save announcements and press 
En te r.
Shut Down DEFINITY AUDIX System
!WA R N I N G :
Neglecting to shut down an AUDIX assembly before powering down the system cabinet 
where it resides can damage the AUDIX disk.
1. Shut down the AUDIX assembly and allow the disk to completely spin 
down.
Power Down SCC Cabinet Stack
1. At the cabinet stack being upgraded, set the circuit breaker to OFF.
2. Unplug the power cord from the receptacle of each cabinet.
Position Port Cabinets
1. Stack the port cabinets on top of the control cabinet (A) or expansion 
control cabinet (B, if present). See Figure 6-23
. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-72 Adding SCC Port Cabinets 
6
2. Install cabinet labels on the front and rear of cabinets to the left of the 
circuit pack labels. Label the second cabinet “B”, the third cabinet “C”, and 
the four th cabinet “D”.
Figure 6-23. PPN Cabinet — Front View
Connect TDM or TDM/LAN Cables
1. Disconnect the TDM or TDM/LAN bus terminator from Slot 22 of the control 
cabinet, or from Slot “18” of an expansion control cabinet, or from Slot “17” 
of a por t cabinet.  Figure Notes
1. Control Cabinet or Expansion 
Control Cabinet (“A” Position)
2. Port Cabinet (“B” Position)3. Port Cabinet (“C” Position)
4. Port Cabinet (“D” Position) 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-73 Adding SCC Port Cabinets 
6
2.Move the terminator to slot “17” of the top port cabinet. See Figure 6-24, 
Figure 6-25
, or Figure 6-26.
3. Connect the TDM/LAN cables behind the lower rear cover.
Figure 6-24. TDM/LAN Connections for Standard or High Reliability PPN or 
EPN Figure Notes
1. AHF110 TDM/LAN Bus Terminator
2. Slot 17
3. TDM/LAN Cable (WP91716 L3)
4. Slot 00
5. Slot 226. Slot 02
7. Port Cabinet (“D” Position)
8. Port Cabinet (“C” Position)
9. Port Cabinet (“B” Position)
10. Control Cabinet (“A” Position) 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-74 Adding SCC Port Cabinets 
6
Figure 6-25. TDM/LAN Connections High or Critical Reliability PPN Figure Notes
1. AHF110 TDM/LAN Bus Terminator
2. Slot 17
3. TDM/LAN Cable (WP91716 L3)
4. Slot 00
5. Slot 226. Slot 02
7.Port Cabinet (“D” Position)
8. Port Cabinet (“C” Position)
9. Duplicated Control Cabinet (“B” Position)
10. Control Cabinet (“A” Position) 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-75 Adding SCC Port Cabinets 
6
Figure 6-26. TDM/LAN Connections for Critical Reliability EPN Figure Notes
1. AHF110 TDM/LAN Bus Terminator
2. Slot 17
3. TDM/LAN Cable (WP91716 L3)
4. Slot 00
5. Slot 186. Slot 01 (TDM/LAN Bus Terminator)
7.Port Cabinet (“D” Position)
8. Port Cabinet (“C” Position)
9. Port Cabinet (“B” Position)
10. Expansion Control Cabinet (“A” 
Position) 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-76 Adding SCC Port Cabinets 
6
Connect ICC Cables 
If the new port cabinet is cabinet B” of a critical reliability EPN, install ICC cables. 
1. Connect the cables to the “ICC” block on expansion control cabinet A and 
port cabinet B. Install each cable so the dark stripe on the cable is on the 
bottom. See Table 6-10
, Figure 6-27, and Figure 6-28.
Figure 6-27. ICC Pin-Field Blocks on J58890N Expansion Control Cabinet
Table 6-10. Intercabinet Cable Connections
Connect ICC Cables
From To
CarrierPin-Field 
Block CarrierPin-Field 
Block
EPN J58890N ICCA
ICCBJ58890H ICCA
ICCB
114 25 12
24
00  00
20 19  20 19
0  3 2 1
2 1  2 1 ICCB ICCA  TERM
CURL
Pinfield