Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Upgrades And Additions Manual

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R7si to R8si 
5-11 Upgrade the Software 
5
2. Type the day in English (Sunday through Saturday) in the Day of the 
Week: field. See Table 5-2
 for English day names. When done, press Ta b 
to move to next field.
3. Type the current month in English (January through December) in the 
Month: field. See Table 5-3
 for English month names. When done, press 
Ta b to move to next field.
4. Type the day of month (1 through 31) in the Day of the Month: field 
and press 
Ta b to move to the next field.
5. Type the current year in the Year: field and press 
TA B to move to the next 
field.
6. Type the current hour for a 24-hour clock in the Hour: field and press
 Ta b to 
move to the next field.
7. Type the current minute (0 through 59) in the Minute: field (seconds 
cannot be set). When done, press 
Ta b to move to next field
Table 5-2. English Day of the Week Names
Day Number Day Name
1 Sunday
2 Monday
3 Tuesday
4 Wednesday
5 Thursday
6Friday
7 Saturday
Table 5-3. English Month Names
Number Name Number Name
1 January 7 July
2 February 8 August
3 March 9 September
4 April 10 October
5 May 11 November
6 June 12 December 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R7si to R8si 
5-12 Upgrade the Software 
5
8. Type standard or daylight savings in the Type field, according to the 
current time in the local time zone. For example, if currently on standard 
time, type standard.
9. Type the rule number in the Daylight Savings Rule field.
10. When all the information is correct, press 
En te r.
11. Type display time and press 
En t e r to verify date and time data.
Verify Additional Administration
For standard reliability:
1. Type list configuration software-version and press 
En t e r to verify the 
system software version (in the Memory Resident field).
For high or critical reliability:
1. Type list configuration software-version long and press 
En t e r to verify 
the system software version (in the Memory Resident field)
For all reliabilities:
2. Perform a sanity check on the system by executing the following 
commands to ensure the translations were read in properly:
a. list station
b. list trunk-group
c. list hunt-group
This ensures there is no translation corruption and the translations can be 
saved with the new software.
3. Notify the switch administrator that for any previous login names and 
passwords that still exist, the passwords expire in 24 hours. When 
changed, the new login names and passwords must conform to the 
following requirements:
As before, a login name must have 3 to 6 alphanumeric characters. A 
password must have 4 to 11 characters, including at least 1 alphabetic 
character and 1 numeric character. 
4. Since an R1V3.0 G3-MA cannot notify users about expiring passwords, 
disable password aging for any login name used with an R1V3.0 G3-MA.
Enable TTI
NOTE:
Do this step only if the TTI is disabled and you want it enabled.
1. Type change system-parameters features and press 
En te r to change the 
TTI field back to its value before the upgrade. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R7si to R8si 
5-13 Upgrade the Software 
5
Enable Scheduled Maintenance
1. Type change system-parameters maintenance and press En t e r to enable 
the scheduled daily maintenance.
2. Check the Start Time and Stop Time fields.
Enable Customer Options and Alarm Origination
1. Get the DOSS order number of the upgrade from the project manager and 
ask the regional Customer Software Administration to complete the steps 
in the shaded box. See ‘‘Where to Call for Technical Support’’ on page -xx
 
for telephone numbers.
NOTE:
As part of the system registration process, the INADS Database 
Administrator enables Alarm Origination.
2. When administration is completed, log in as craft at the Login: prompt.
Resolve Alarms
1. Type display alarms and press En te r to examine the alarm log. Resolve 
any alarms that may exist using 
DEFINITY Enterprise Communications 
Server Maintenance for R8si
. 
init login administration:
1. Log in as init.
2. Type change system-parameters customer-options and press 
En t e r 
to verify that the customer options are properly set.
3. Go to screen 6, QSIG Optional Features, and set the Basic Call 
Setup field to y if the customer was using Supplementary Services 
Protocol b or d on an ISDN-PRI trunk group before the upgrade.
4. Type change system-parameters offer-options and press 
En t e r.
5. If the Activate Offer field is n, set it to y and press 
Ta b. A warning 
message lets you know whether you need to save translations and 
reboot to make the change permanent.
6. Press 
En te r to effect the changes or Canc el if there were no changes.
7. Contact the requester when done. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Upgrading R7si to R8si 
5-14 Upgrade the Software 
5
Check Link Status
1. Type display communication-interface links and press En t e r. 
2. Type status link 
number and press En t e r. Verify that the service 
status field is set to in service. Repeat this step for each link.
Save Translations
1. Type save translation and press En t e r to copy upgraded translations in 
memory to the translation card, which takes about 10 minutes.
Restore Announcements (if necessary)
1. Type restore announcements and press En t e r to copy announcements 
from the translation card to memory, which takes about 40 minutes.
Return Replaced Equipment
1. Return replaced equipment to Lucent Technologies according to the 
requirements outlined in:
BCS/Material Logistics, MSL/Attended Stocking Locations
Methods and Procedures for Basic Material Returns
2. Return the old translation card to Lucent Technologies. 
						

							Adding or Removing Hardware 
6-1 Add Circuit Packs 
6
DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
6
Adding or Removing Hardware
This chapter details the information required to install some equipment associated 
with upgrading an existing system. 
For more information about installing cabinets, refer to DEFINITY Enterprise 
Communications Server Release 8 Installation and Test for Single-Carrier 
Cabinets.
For more information about installing adjuncts and peripheral devices, refer to 
DEFINITY Enterprise Communications Server Release 8 Installation for Adjuncts 
and Peripherals
.
Add Circuit Packs
When installing additional features or equipment, it may be necessary to install 
additional circuit packs.  This is a general procedure to use when adding features 
or equipment that require adding circuit packs.
1. Log onto the system and answer y to the 
Suppress Alarm Origination 
question during login.
2. Install the circuit pack into the carrier.
3. Log off the system after the addition (and any required administration) is 
complete.
For information about administering circuit packs and other equipment, refer to 
DEFINITY Enterprise Communications Server Release 8 Administrator’s Guide. 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-2 List of Circuit Packs 
6
List of Circuit Packs 
Table 6-1 lists the c irc uit p ac ks sorted  b y ap p aratus c od e, inc lud ing c irc uit 
p ac ks used  in non-United  States installations.
Table 6-1. Circuit Packs and Circuit Modules 
Apparatus Code Name Type
631DA1 AC Power Unit Power
631DB1 AC Power Unit Power
644A1 DC Power Unit Power
645B1 DC Power Unit Power
649A DC Power Unit Power
676B/C DC Power Supply Power
982LS Current Limiter Power
CFY1B Current Limiter Power
CPP1 Memory Expansion  Control
ED-1E546
(TN2169)
(TN2170)
(TN566)
(TN567)DEFINITY AUDIX R3 System Port 
Assembly
ED-1E546
(TN2208)
(TN2170)Call Visor ASAI over the DEFINITY (LAN) Gateway R1 Port 
Assembly
J58890M1
TN801)CallVisor ASAI/CallVisor PC/LAN over the DEFINITY 
LAN Gateway R2Port 
Assembly
TN417 Auxiliary Trunk Port
TN419B Tone-Clock Control
TN420B/C Tone Detector Service
TN429B/C/D Direct Inward/Outward Dialing (DIOD) Trunk Port
TN433 Speech Synthesizer Service
TN436B Direct Inward Dialing Trunk Port
TN437 Tie Trunk - Australia Port
TN438B Central Office Trunk Port
TN439 Tie Trunk Port
TN447 Central Office Trunk Port
TN457 Speech Synthesizer Service
Continued on next page 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-3 List of Circuit Packs 
6
TN458 Tie Trunk - U.K. Port
TN459B Direct Inward Dialing Trunk Port
TN464C/D/E/F DS1 Interface - T1, 24 Channel - E1, 32 Channel Port
TN465/B/C Central Office Trunk Port
TN467 Analog Line Port
TN468B Analog Line Port
TN479 Analog Line Port
TN497 Tie Trunk - Italy Port
TN553 Packet Data Line Port
TN556B/C/D ISDN-BRI 4-Wire S/T-NT Interface Port
TN570/B/C Expansion Interface Port
TN722B DS1 Tie Trunk Port
TN725B Speech Synthesizer Service
TN726/B Data Line Port
TN735 MET Line Port
TN742 Analog Line Port
TN744/B Call Classifier Service
TN744/C/D Call Classifier - Detector Service
TN746/B Analog Line Port
TN747/B Central Office Trunk Port
TN748/B/C/D Tone Detector Service
TN750/B/C Announcement Service
TN753/B Direct Inward Dialing Trunk Port
TN754/B/C Digital Line 4-Wire DCP Port
TN755/B Neon Power Unit Power
TN758 Pooled Modem Port
TN760B/C/D/E Tie Trunk Port
TN762/B Hybrid Line Port
TN763B/C/D Auxiliary Trunk Port
TN765 Processor Interface Control
TN767B/C/D/E DS1 Interface - T1, 24 Channel Port
TN768 Tone-Clock Control
TN769 Analog Line Port
TN771/D Maintenance/Test Service
Table 6-1. Circuit Packs and Circuit Modules  — Continued
Apparatus Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-4 List of Circuit Packs 
6
TN773 Processor Control
TN775/B/C Maintenance Service
TN776 Expansion Interface Port
TN780 Tone-Clock Control
TN786/B Processor Control
TN787F/G/H/J/K Multimedia Interface Service
TN788B Multimedia Voice Conditioner  Service
TN789 Radio Controller Control
TN790/B Processor Control
TN792 Duplication Interface (DUPINT) Control
TN793 Analog Line (24-port) Port
TN794 Network Control/Packet Interface Control
TN794/TN2400 Network Control Interface Assembly (combination of 
the TN794 and TN2400 circuit packs)Control
TN796B Processor Control
TN797 Analog CO Trunk and Line Combo Port
TN799B Control-LAN (C-LAN) Port
TN802B IP Interface Assembly Port
TNPRI/BRI PRI to BRI Converter Port
TN2135 Analog Line Port
TN2136 Digital Line 2-Wire DCP Port
TN2138 Central Office Trunk Port
TN2139 Direct Inward Dialing Trunk Port
TN2140/B Tie Trunk - Hungary, Italy Port
TN2144 Analog Line Port
TN2146 Direct Inward Dialing Trunk Port
TN2147/C Central Office Trunk Port
TN2149 Analog Line Port
TN2180 Analog Line Port
TN2181 Digital Line 2-Wire DCP Port
TN2182/B Tone-Clock -Tone Detector and Call Classifier Control
TN2183 Analog Line Port
TN2184 DIOD Trunk Port
TN2198 ISDN-BRI 2-Wire U Interface Port
TN2199 Central Office Trunk Port
Table 6-1. Circuit Packs and Circuit Modules  — Continued
Apparatus Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-5 Installing Fiber Optic Cable Pass-Thru Kit (SCC) 
6
Installing Fiber Optic Cable Pass-Thru 
Kit (SCC)
This section details the installation of the DEFINITY fiber optic pass-thru kit for 
Single-Carrier Cabinets (SCC) only. This kit (comcode 848029278) provides the 
equipment necessary to install the fiber optic connectors and associated cabling. 
Unpack and Inspect
1. Verify the equipment received. See Figure 6-1. Actual equipment may vary 
in appearance and may ship in separate packages. 
2. See Table 6-2
 for a list of part comcodes. TN2202 Ring Generator Power
T N 222 4/B Digital Line, 24-Port, 2-Wire D C P P or t
TN2305 ATM Interface (Multimode) Port
TN2306 ATM Interface (Single Mode) Port
TN2313 DS1 Interface Port
WP-91153 AC Power Supply (Single-Carrier Cabinet) Power
Table 6-1. Circuit Packs and Circuit Modules  — Continued
Apparatus Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
Adding or Removing Hardware 
6-6 Installing Fiber Optic Cable Pass-Thru Kit (SCC) 
6
Figure 6-1. Fiber Pass-Thru Kit EquipmentFigure Notes
1. Pass-thru Tool
2. SC-SC Fiber Optic Adapter
3. ST-SC Fiber Optic Adapter
4. Fiber Optic Cable5. Fiber Optic Cable Disconnect Label
6. I/O Connector Adapter Bracket
7. Cable Tie
8. Cable Tie Mount
indapkit RPY 012398
1
2
3
4
5
6
7
8