Konica Minolta magicolor 5670EN User Manual

							CompactFlash card 257
CompactFlash card
If a CompactFlash card is installed, resources such as fonts, macros and pro-
files can be downloaded, and image files can be printed directly.
Only CompactFlash cards with a capacity of 512 MB, 1 GB or 4 GB 
can be used.
The Hold Job function is not available with a CompactFlash card. 
These functions require that an optional hard disk kit be installed.
Installing the CompactFlash card
Note
If the installed CompactFlash card was used with a device other than 
this printer, such as a computer or digital camera, the card is 
automatically formatted and all of its data is deleted.
Note
It is very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 250. In addition, 
always handle circuit boards by their edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash card 258
2Using a screwdriver, remove the 
screw. Then, slide the rear cover 
to the right and remove it.
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
4Slide the panel slightly to the 
right and lift it off the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash card 259
5Fully insert the CompactFlash 
card into the appropriate slot.
When the CompactFlash card is 
correctly inserted, the button on 
the top side of the slot (circled in 
the illustration) slightly pops out.
Before removing the 
CompactFlash card, 
press in this button.
6Reinstall the panel and tighten the seven screws.
7Attach the rear cover.
8Reconnect all interface cables.
9Reconnect the power cord, and 
turn on the printer.
10Declare the Memory card in the Windows printer driver (Properties/Con-
figure tab).
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option 260
Duplex Option
Duplex (double-sided) printing can be performed automatically with the 
duplex option and enough memory installed. See “Duplexing” on page 147.
Installing the Duplex Option
1Turn off the printer.
2Remove the cover on the right 
side cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option 261
3Remove the door at the side of 
the right side cover.
4Prepare the duplex option.
Before installing the 
duplex option, open the 
duplex cover, and then 
check that the knob is 
positioned as shown in 
the illustration. Then, 
close the duplex cover.
5Attach the duplex option, as 
shown in the illustration.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option 262
6Open the duplex cover, and then 
turn both knobs counterclock-
wise until they are horizontal to 
secure the duplex option to the 
right side cover.
7Then, close the duplex cover.
8Declare the Duplex Unit in the Windows printer driver (Properties/Config-
ure tab).
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 263
Lower Feeder Unit
You can install up to two optional lower feeder units (Trays 3 and 4). Each 
lower feeder unit increases your printer’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
„Four metal brackets
–Two front brackets
–Two rear brackets
„Four securing screws
„Transport guide (used only for Tray 3)
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 264
Installing a Lower Feeder Unit 
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be installed onto the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 265
4With another person’s help, 
place the printer on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
printer.
If two lower feeder units are to be installed, stack the two lower 
feeder units and secure them together before installing them to the 
printer.
WARNING!
This printer weighs approximately 44 kg (97.0 lb) when it is fully loaded 
with consumables. The printer must be lifted by two people.
5Using a screwdriver, install the 
two securing brackets at the rear 
of the printer.
44 kg97 lbs
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 266
6Pull out the trays.
7Install the two securing brackets 
at the front of the printer.
8Close the trays.
9Attach the transport guide to the 
right door of Tray 3.
It is not necessary to 
attach the transport guide 
to the right door of Tray 4.
Downloaded From ManualsPrinter.com Manuals