Konica Minolta magicolor 5670EN User Manual

							Status, Error, and Service Messages 247 Service Messages:
These messages indicate a more serious error that can only be corrected by 
a customer service engineer. If one of these messages appears, turn the 
printer off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.  
This service 
message...means... do this...
SERVICE CALL XXXX
“Error”An error has been 
detected with the item 
indicated “XXXX” in the 
service message.
Information about errors 
appears at the bottom of 
the message window.Reboot the printer. This 
often clears the service 
message, and printer 
operation can resume. 
If the problem persists, 
contact Technical Sup-
port.
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 248
Downloaded From ManualsPrinter.com Manuals 
						

							11
Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 250
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present. Plastic, rubber, wood, painted metal surfaces, and telephones 
are not acceptable grounding points.
If you don’t have an antistatic wrist strap, discharge your body’s static 
electric charge by touching a grounded surface before you handle any 
printer boards or components. Also avoid walking around after 
grounding yourself.Dual In-Line 
Memory Module 
(DIMM)256 MB, 512 MB DIMM 
(DDR-SDRAM, 266 MHz, 184 pins, No ECC, Unbuf-
fered, CL=2 or 2.5)
Duplex OptionAuto duplexing
Lower Feeder Unit
(Tray 3/4)500-sheet tray included
Hard Disk Kit40 GB Hard Disk
CompactFlash card512 MB, 1 GB, 4 GB
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 251
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing. 
Dual in-line memory module (or DIMM) is compact circuit board with sur-
face-mount memory chips.
The printer, which has two memory slots, has a 256 MB memory module 
already installed in one of the slots. By using both slots, the memory can be 
expanded to a maximum of 1024 MB (512 MB + 512 MB).
Installing a DIMM
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 250. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove the 
screw. Then, slide the rear cover 
to the right and remove it.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 252
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
4Slide the panel slightly to the 
right and lift it off the printer.
5Insert the new DIMM straight 
into the DIMM connector until 
the latches snap into the locked 
position.
Observe the keyed side of the 
DIMM to align it with the connec-
tor. If you cannot snap the DIMM 
into place, do not force it. Repo-
sition it, making sure that the 
DIMM is seated completely in 
the connector.
6Reinstall the panel and tighten the seven screws.
7Attach the rear cover.
8Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 253
9Reconnect the power cord, and 
turn on the printer.
10Declare the additional Printer Memory in the Windows printer driver 
(Properties/Configure tab).
11Print a configuration page (PRINT MENU/CONFIGURATION PG) and 
verify that the total amount of the RAM installed in your printer is listed.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit 254
Hard Disk Kit
If a hard disk kit is installed, fonts can be downloaded and saved, and the 
overlay function can be used.
Installing the Hard Disk kit
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 250. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove the 
screw. Then, slide the rear cover 
to the right and remove it.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit 255
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
4Slide the panel slightly to the 
right and lift it off the printer.
5Plug the cable on the hard disk 
kit into the connector on the con-
troller board.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit 256
6Insert the three mounting pins 
on the hard disk kit into the holes 
in the controller board to mount 
the hard disk kit onto the control-
ler board.
7Reinstall the panel and tighten the seven screws.
8Attach the rear cover.
9Reconnect all interface cables.
10Reconnect the power cord, and 
turn on the printer.
11Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
Downloaded From ManualsPrinter.com Manuals