Konica Minolta magicolor 4690MF User Manual

							Status, Error, and Service Messages 249
USB MEMORY FULLThere is no space 
available on the 
USB memory 
device connected to 
this machine.Delete data from the 
USB memory device to 
create free space, or 
use a different USB 
memory device.
xxx COVER OPEN
CLOSE xxx COVERThe indicated cover 
is open.Close the indicated 
cover.
xxx DOOR OPEN
CLOSE xxx DOORThe indicated door 
is open.Close the indicated 
door.
xxx SERVER ERRORThe file cannot be 
saved on the indi-
cated server.Check the status of the 
indicated server.
WASTE TONER FULL
REPLACE BOTTLEThe waste toner 
bottle is full.Replace the waste 
toner bottle.
Waste Near FullThe waste toner 
bottle will soon be 
full.Prepare a waste toner 
bottle.
Wrong I-Unit xAn imaging unit 
incompatible with 
the machine is 
installed.Replace the indicated 
imaging unit with a cor-
rect one.
WRONG PASSWORD
xxxThe password is 
incorrect, so the 
indicated server 
could not be 
accessed.Check the password, 
and then specify the 
correct one.
Wrong Toner xA toner cartridge 
incompatible with 
the machine is 
installed.Replace the indicated 
toner cartridge with a 
correct one. This message... means... Do this...
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 250
Service Messages
These messages indicate a more serious fault that can only be corrected by a 
customer service engineer. If one of these messages appears, turn the 
machine off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
This service message... means... Do this...
MACHINE TROUBLE
SERVICE CALL (xxxx)An error has been 
detected with the item 
indicated “
xxxx” in 
the service message.Reboot the machine. 
This often clears the 
service message, 
and machine opera-
tion can resume. 
If the problem per-
sists, contact Techni-
cal Support.
Downloaded From ManualsPrinter.com Manuals 
						

							10
10Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 252
Introduction
Note
Any damage to the machine caused by the use of accessories not 
manufactured or supported by KONICA MINOLTA will void your 
warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the machine and 
accessories are turned off and unplugged during installation.
For details on the available options, refer to 
http://printer. konicaminolta.com. Tr a y  3Lower feeder unit with 500-sheet tray included
Downloaded From ManualsPrinter.com Manuals 
						

							Antistatic Protection 253
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present. Plastic, rubber, wood, painted metal surfaces, and telephones 
are not acceptable grounding points.
If you don’t have an antistatic wrist strap, discharge your body’s static 
electric charge by touching a grounded surface before you handle any 
printer boards or components. Also avoid walking around after 
grounding yourself.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 3 (Lower Feeder Unit) 254
Tray 3 (Lower Feeder Unit)
You can install up to one optional lower feeder unit (Tray 3). The lower feeder 
unit increases your machine’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 3 (Lower Feeder Unit) 255 Installing Tray 3
Note
Since consumables are installed in the machine, be sure to keep the 
machine level when moving it in order to prevent accidental spills.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be installed onto the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							
Tray 3 (Lower Feeder Unit)
256
4With another person’s help, 
place the machine on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
machine.
WARNING!
This machine weighs approximately 55 kg (121 lb) when it is fully 
loaded with consumables. The machine must be lifted by two people.
5Close the right side cover of the 
lower feeder unit.
6Reconnect all interface cables.
55 kg121 lbs
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 3 (Lower Feeder Unit) 257
7Reconnect the power cord, and 
turn on the machine.
8From the printer driver, correctly specify the setting for Tray 3.
For details on specifying printer driver settings, refer to “Selecting 
Printer Driver Options/Defaults (for Windows)” on page 98.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 3 (Lower Feeder Unit) 258
Downloaded From ManualsPrinter.com Manuals