Comdial Impact Dsu Instructions Manual
Have a look at the manual Comdial Impact Dsu Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 133 Comdial manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Upper Case Character Chart Character Code A21 B22 C23 D31 E32 F33 G41 H42 I43 J51 K52 L53 M61 N62 O63 P71 Q11 R72 S73 T81 U82 V83 W91 X92 Y93 Z13Lower Case Character Chart Character Code a24 b25 c26 d34 e35 f36 g44 h45 i46 j54 k55 l56 m64 n65 o66 p74 q14 r75 s76 t84 u85 v86 w94 x95 y96 z16 Symbol And Number Character Chart Character Code SPACE 12 ;17 /18 “19 .27 ,28 :29 101 202 303 404 505 606 707 808 909 IMI66–107Digital Telephone System System Programming 3 – 29
3.4.12 Tandem Attendant Description:When you enable this feature, a recall from an unanswered call transfer or timed hold recall will ring at both attendant stations. When you disable it, only the attendant station that transferred the call will ring. To Program:1. Dial24.“TANDEM ATTN XXX ” 2. PressA1to toggle between enable and disable (LED On = Enable) —OR— dial1to Enable (A1 LED is on)“TANDEM ATTN ON” dial2to Disable.“TANDEM ATTN OFF ” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. 3.4.13 Tone or Voice Signaling Description:Intercom calls can be tone signaled or voice signaled. Use this programming feature to select the system’s signaling choice. With either method set as the system’s first choice, the user can choose the other method as needed. To Program:1. Dial16.“XXXXX ANN. FIRST” 2. PressA1to toggle between Voice To Tone (LED On = voice signaling) —OR— dial1for Voice First“VOICE ANN. FIRST” dial2for Tone First.“TONE ANN. FIRST” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. Digital Telephone SystemIMI66–107 3 – 30 System Programming
3.4.14 Inhibiting System Features Description:You can disable certain features system-wide to prevent unauthorized users from tampering with the system. You can performing the system default procedure to re-enable features that you disable with this feature inhibit procedure. To Program:1. Dial29.“FEATURE INHIBIT” 2. Select feature. —Dial 01 to disable Line Group 1 —Dial 02 to disable Line Group 2 —Dial 03 to disable Line Group 3 —Dial 04 to disable Line Group 4 —Dial 05 to disable Zone 1 Paging —Dial 06 to disable Zone 2 Paging —Dial 07 to disable Zone 3 Paging —Dial 08 to disable All Call —Dial 09 to disable Meet Me Page —Dial 10 to disable Night Transfer —Dial 11 to disable Background Music —Dial 12 to disable Voice Announce Block —Dial 13 to disable Message Waiting —Dial 14 to disable Call Pickup —Dial 15 to disable Call Forward —Dial 16 to disable Automatic Call Back —Dial 17 to disable Station-to-Station Messaging —Dial 18 to disable Line Group Queue —Dial 19 to disable Directed Station Hold —Dial 20 to disable Call Park orbit 1 —Dial 21 to disable Call Park orbit 2 —Dial 22 to disable Call Park orbit 3 —Dial 23 to disable Call Park orbit 4 —Dial 24 to disable Call Park orbit 5 —Dial 25 to disable Call Park orbit 6 —Dial 26 to disable Call Park orbit 7 —Dial 27 to disable Call Park orbit 8 —Dial 28 to disable Call Park orbit 9 —Dial 29 to disable Call Waiting —Dial 30 to disable LCD Messaging —Dial 31 to disable Executive Override/Service Observing —Dial 32 to disable Account Code —Dial 33 to disable Personal Call Forward —Dial 34 to enable all features —Dial Sfor next item —Dial SSfor configuration mode. IMI66–107Digital Telephone System System Programming 3 – 31
3.5 System Timing The digital telephone system has several attributes that control timing dimensions of system operation. The following features set these various timing attributes. 3.5.1 Call Park Recall Time Description:A call that remains in a parking orbit for a programmed length of time automatically returns to a timed hold recall condition at the parking station. Set the call park recall time with this programming feature. To Program:1. Dial22.“C.P. RECALL X 2. Select recall time (program button LED On = Selected Time) — Dial1or pressA1= 1 min“C.P. RECALL 1” — Dial2or pressA2= 2 min“C.P. RECALL 2” — Dial3or pressA3= 3 min“C.P. RECALL 3” — Dial4or pressA4= 4 min“C.P. RECALL 4” —Dial5or pressA5= 5 min“C.P. RECALL 5” —Dial6or pressA8= 6 min“C.P. RECALL 6” —Dial7or pressA9= Never Recall.“NEVER RECALL” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. Digital Telephone SystemIMI66–107 3 – 32 System Programming
3.5.2 Extended DTMF Tones For Automatic Dialing Description:When a telephone user dials a number automatically (autodial, saved number redial, etc), the duration of the generated DTMF tones are as you set them with this programming option. This feature is useful when automatically dialed numbers access answering machines, banking computers, or voice mail, for example, that require DTMF tones that are longer than standard tones. To Program:1. Dial26.“DTMF DIALNG XXXX” 2. Choose DTMF tone length —Dial01or pressA1= 60 msec“DTMF DIALNG 60” —Dial02or pressA2= 80 msec“DTMF DIALNG 80” —Dial03or pressA3= 100 msec“DTMF DIALNG 100” —Dial04or pressA4= 120 msec“DTMF DIALNG 120” —Dial05or pressA5= 160 msec“DTMF DIALNG 160” —Dial06or pressA6= 240 msec“DTMF DIALNG 240” —Dial07or pressA7= 320 msec“DTMF DIALNG 320” —Dial08or pressA8= 400 msec“DTMF DIALNG 400” —Dial09or pressA9= 480 msec“DTMF DIALNG 480” —Dial10or pressA10= 560 msec“DTMF DIALNG 560” —Dial11or pressA11= 720 msec“DTMF DIALNG 720” —Dial12or pressA12= 880 msec“DTMF DIALNG 880” —Dial13or pressA13= 1040 msec“DTMF DIALNG 1040” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. IMI66–107Digital Telephone System System Programming 3 – 33
3.5.3 Pause Time Description:During auto dials and speed dials, it is sometimes necessary to delay the sending of digits to give switching equipment time to prepare for receiving them. A pause is stored for this purpose whenever the user presses theHOLDbutton. You can set the length of the pause with this programming feature. To Program:1. Dial13.“PAUSE TIME XXX” 2. Select time. —Dial1or PressA1“PAUSE TIME 0.50” —Dial2or PressA2“PAUSE TIME 1” —Dial3or PressA3“PAUSE TIME 1.50” —Dial4or PressA4“PAUSE TIME 2” —Dial5or PressA5“PAUSE TIME 3” —Dial6or PressA8“PAUSE TIME 5” —Dial7or PressA9“PAUSE TIME 7.50” —Dial8or PressA10“PAUSE TIME 10” —Dial9or PressA11“PAUSE TIME 15” —Dial0or PressA12.“PAUSE TIME 20” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. 3.5.4 Recall/Flash Description:The system can generate either a line disconnect (recall) or a host system feature access signal (flash) depending upon the programmed time. To Program:1. Dial12.“RECALL/FLSH XXXX” 2. Select time. —Dial1or PressA1“RECALL/FLSH 0.08” —Dial2or PressA2“RECALL/FLSH 0.30” —Dial3or PressA3“RECALL/FLSH 0.50” —Dial4or PressA4“RECALL/FLSH 0.60” —Dial5or PressA5“RECALL/FLSH 0.75” —Dial6or PressA8“RECALL/FLSH 0.88” —Dial7or PressA9“RECALL/FLSH 1” —Dial8or PressA10“RECALL/FLSH 1.50” —Dial9or PressA11“RECALL/FLSH 2” —Dial0or PressA12.“RECALL/FLSH 3” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. Digital Telephone SystemIMI66–107 3 – 34 System Programming
3.5.5 Timed Hold Recall Description:After a call has been on hold for a programmed length of time, the system will recall the station that placed the call on hold. Set the hold recall time with this programming procedure. To Program:1. Dial14.“HOLD RECALL XXX” 2. Select time —Dial1or PressA1“HOLD RECALL 30” —Dial2or PressA2“HOLD RECALL 60” —Dial3or PressA3“HOLD RECALL 90” —Dial4or PressA4“HOLD RECALL 120” —Dial5or PressA5“HOLD RECALL 180” —Dial6or PressA8“HOLD RECALL 240” —Dial7or PressA9“HOLD RECALL 300” —Dial8or PressA10“HOLD RECALL 360” —Dial9or PressA11“HOLD RECALL 420” —Dial0or PressA12.“HOLD RECALL 0” 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. IMI66–107Digital Telephone System System Programming 3 – 35
3.5.6 Unanswered Call Transfer Recall Time Description:A transferred call that remains unanswered after a programmed length of time will return to the transferring station for answering. Set the transfer recall time with this programming procedure. To Program:1. Dial11.“TRANSFER RECALL ” 2. Dial1(station transfer recall)“STA XFR RCL XXX ” —OR— dial2(department transfer recall).“DEPT XFR RCL XXX” 3. Choose transfer time. —Dial1or PressA1“STA XFR RCL 10” —Dial2or PressA2“STA XFR RCL 20” —Dial3or PressA3“STA XFR RCL 25” —Dial4or PressA4“STA XFR RCL 30” —Dial5or PressA5“STA XFR RCL 45” —Dial6or PressA8“STA XFR RCL 60” —Dial7or PressA9“STA XFR RCL 90” —Dial8or PressA10“STA XFR RCL 120” —Dial9or PressA11“STA XFR RCL 180” —Dial0or PressA12.“STA XFR RCL 400” 4. PressSfor next transfer recall feature. 5. PressS Sfor configuration mode. To change setting, repeat procedure and make different selection. Digital Telephone SystemIMI66–107 3 – 36 System Programming
3.6 Line Programming By using line configuration, you can program the parameters for individual lines. The programming decisions you make for a particular line will only be true for that line and not for the entire telephone system. You should make a record in Chapter 4 of all programming decisions that you make—it will help you keep track of what you have done and will help you troubleshoot any problem that might arise later. NOTE:A lighted LED next to the programming button for the selection indicates the current configuration. When a single button provides a toggle (on/off) action, the lighted LED indicates the active feature. The first step in any programming sequence is to enter the base level. Once in this mode, you can dial the feature code for any desired configuration. Enter the base level with the following procedure: press INTERCOMthen dialS# 746S. The last step is to press theSPEAKERbutton to end the programming procedure and return the system to normal operation. To make a line port selection, press a programming button or dial a selection number on the keypad as detailed in the following chart. Table 3–3: Line Port Codes LINE PROG. BUTTONS KEYPAD BUTTONS 1–14 A1–A14 01–14 15, 16 B1, B2 15, 16 17–24 HOLD plus A1–A8 17–24 3.6.1 Abandoned Hold Release Description:When a distant party abandons a hold condition and disconnects from a line (hangs up), the central office will send a forward disconnect signal to the digital telephone system. This signal can be either 50 ms. or 350 ms. in length. Find out from the telephone company what the signal length is, and program the all of the central office line ports to match it using this programming procedure. To Program:1. Dial38.“HOLD RELEASE 50 ” 2. Select hold release time for line ports (LED On = 50 msec). —Line port 1–14 = Dial01–14or pressA1–A14 —Line port 15, 16 = Dial15,16or pressB1,B2 —Line port 17–24 = Dial17– 24or pressHOLDthen pressA1–A8. 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. IMI66–107Digital Telephone System System Programming 3 – 37
3.6.2 Automatic Privacy You can make a line private or non-private. In the private mode, a station has exclusive use of a line during a call. Lines are private unless you re-program them and make them non-private. Private Or Non-Private Lines Description:Use this programming feature to set which lines are private or non-private. To Program:1. Dial40.“PRIVACY RELEASE” 2. Select line ports to be non-private (LED On = Non Private) —Line port 1–14 = Dial01–14or PressA1–A14 —Line port 15, 16 = Dial15,16or pressB1,B2 —Line port 17–24 = Dial17– 24or pressHOLDthen pressA1–A8. 3. DialSfor configuration mode. To change setting, repeat procedure and make different selection. Automatic Privacy Release Description:You can arrange for individual station to automatically release privacy while on certain lines. With this arrangement, other stations can join that particular station whenever it is on the privacy release line. To Program:1. Dial54.“STA/LINE CONFIG.” 2. Dial4.“PRIVACY RELEASE” 3. Select line ports: —Line port 1–14 = Dial01–14or PressA1–A14. —Line port 15, 16 = Dial15,16or pressB1,B2. —Line port 17–24 = Dial17– 24or pressHOLDthen pressA1–A8. 4. Dial#when all line ports are selected. 5. Select station ports to be programmed —Station 10–57 = Dial10–57, or pressC10–C57. 6. DialSwhen all station ports are selected —OR— dialSSfor next station/line feature —OR— dialSSSfor configuration mode. To change setting, repeat procedure and make different selection. Digital Telephone SystemIMI66–107 3 – 38 System Programming