Comdial Impact Dsu Instructions Manual

							3.7.12 Flexible Ringing Assignments
You can enable different ringing assignments for individual lines and stations.
Direct/Delayed Ringing
Description:You must program ringing assignments on a per station/per line basis. You can control
ringing for every line that has appearance at a station assigning immediate, or direct,
ringing to some lines and delayed ringing to others.
NOTE:Do not program direct ringing for lines that you assign to the direct
department calling feature.
To Program:1. Dial54.“STA/LINE CONFIG.”
2. Dial1“DIRECT RING”
—OR—
Dial2.“DELAY RING”
NOTE:For no station ringing, skip step 3 and make no line selection.
3. Select line ports for ringing (LED On = Selected Ports).
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24= Dial 17–24or pressHOLDthen pressA1–A8.
4. Dial # when all line ports are selected.
5. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
6. DialSwhen all station ports are selected
—OR—
dialSSfor next station/line ringing assignment
—OR—
dialSSSfor configuration mode.
To clear current setting, repeat procedure.
IMI66–107Digital Telephone System
System Programming 3 – 59 
						

							Night Transfer (Of Ringing)—Line/Station Assignments
Description:You or the system attendant can place the system into the night transfer (of ringing) mode
of operation. While in this mode of operation, the system will activate special line/station
ringing assignments. Use this procedure to program these assignments.
To Program:1. Dial54.“STA/LINE CONFIG”
2. Dial3.“NIGHT RING”
3. Select line ports for night ringing (LED On = Selected Ports)
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24 = Dial17–24or pressHOLDthen pressA1–A8.
4. Dial # when all line ports are selected.
5. Select station ports (LED On = Feature Assigned)
—Station 10–57 = Dial10 - 57or pressC10–C57.
6. DialSwhen all station ports are selected
—OR—
dialSSfor next station/line feature
—OR—
dialSSSfor configuration mode.
To clear current setting, repeat procedure.
Night Transfer (Of Ringing)—Operation
Description:After you have assigned Night Transfer (Of Ringing) to all desired the stations and lines,
you must enable the feature operation with this procedure.
To Program:1. Dial03.“NIGHT XFER XXX ”
2. PressA1to toggle between enable and disable (LED On = Enabled)
—OR—
dial1to Enable (A1 LED on)“NIGHT XFER ON ”
dial2to Disable.“NIGHT XFER OFF”
3. DialSfor configuration mode.
To change setting, repeat procedure and make opposite selection.
Digital Telephone SystemIMI66–107
3 – 60 System Programming 
						

							Delayed Ringing Times
Description:You assign delayed ringing to stations for specific lines, you can also set the time length
of the delay.
To Program:1. Dial17.“SYSTEM FEATURES ”
2. Dial05.“DELAY RING XX”
3. Select delay time (LED On = Selected Time)
—Dial1or pressA1= 6 seconds“DELAY RING 6”
—Dial2or pressA2= 12 seconds“DELAY RING 12”
—Dial3or pressA3= 18 seconds“DELAY RING 18”
—Dial4or pressA4= 24 seconds“DELAY RING 24”
—Dial5or pressA5= 30 seconds“DELAY RING 30”
—Dial6or pressA8= 36 seconds“DELAY RING 36”
—Dial7or pressA9= 42 seconds“DELAY RING 42”
—Dial8or pressA10= 48 seconds“DELAY RING 48”
—Dial9or pressA11= 54 seconds“DELAY RING 54”
—Dial0or pressA12= 60 seconds“DELAY RING 60”
4. DialSSfor configuration mode.
5. PressSPEAKERto end.
To clear current setting, repeat procedure and make different selection.
Allow Ringer Off
Description:With the operating system parameters set to default, the rocker switch volume control on
DigiTech andImpactmultiline telephones sets the ringer volume level between off and a
maximum level. You can disable the allow ringer off on a system-wide basis. When you
do this, users can set the ringer volume of their telephones between a minimum and a
maximum level, but can not completely silence it.
To Program:1. Dial17.“SYSTEM FEATURES ”
2. Dial04.“RING OFF XXXXXX”
3. Press A1 to toggle between ringer off allow and not allow.
(LED On = Ringer Off allowed)
—OR—
Dial1to allow ringer off.“RING OFF ENABLE”
Dial2to not allow ringer off.“RING OFF DISABLE”
4. DialSSfor configuration mode.
5. PressSPEAKERto end.
IMI66–107Digital Telephone System
System Programming 3 – 61 
						

							3.7.13 Flexible Station Numbering
Description:The system supports a flexible station numbering plan for calling individual stations and
departments. You can program each station port to respond to the dialing of any available
number between 10 and 7999; however, the system will not allow you to assign the same
dialing code as both a station extension number and a department access code, nor will
the system allow you to assign an extension number or access code conflict such as 15
and 1500.
To Program:1. Dial52.“ACCESS CODE”
2. Dial1to assign extension number. “ASSIGN EXT. NUM”
3. Select station port“EXT. XXXX ”
—Station 10–57 = Dial10–57or pressC10–C57.
4. Dial new extension number.“EXT. XXXX YYYY ”
NOTE:Extension number can be max. of four digits. If less than four digits, leading
zeros must be dialed before number. (Example: For ext. no. 15, dial 0015).
5. Select next station number and assign extension number
—OR—
dialSfor configuration mode.
To change setting, repeat procedure and make a different selection.
3.7.14 Group Call Pickup
Description:If a call rings to any station in a prearranged group, a user at another station in that group
can dial a group pickup code and answer the call. Assign the stations to call pickup
groups using this procedure.
To Program:1. Dial53. “STATION FEATURES”
2. Dial16.“GRP. CALL PICKUP”
3. Dial 0 for no group
—OR—
dial1–4for group 1–4.“GROUP X ”
4. Select station ports (LED On = Feature Assigned)
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor next group
—OR—
dialSSfor next station feature
—OR—
dialSSSfor configuration mode.
To remove station from call pickup group, assign it to group 0.
Digital Telephone SystemIMI66–107
3 – 62 System Programming 
						

							3.7.15 Handset Volume Control On Impact Telephones
Description:Impacttelephones have 8 handset volume settings at default. You may increase the
number of volume settings to 13 on an individual station basis.
To Program:1. Dial53.“STATION FEATURES”
2. Dial38.“HANDSET VOLUME”
3. Select station ports (LED on = Feature Assigned):
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To change setting, repeat procedure and make different selection.
IMI66–107Digital Telephone System
System Programming 3 – 63 
						

							3.7.16 Headset Interface
You can program LCD speakerphones equipped with the optional headset jack to use a headset as well as
the handset or speakerphone.
NOTE:The system delivers subdued off-hook voice announcements (SOHVA) to the headset.
Because a headset exhibits a coupling effect between the earpiece and microphone, it may
allow the outside party to hear a SOHVA message. You should inform the user of this
possibility.
Headset Operation As A Class Of service
Description:When employing DigiTech speakerphones (models 7700S, rev. H and earlier, and 7016S
only), you must use this programming procedure to arrange for a station port to allow
headset operation.
To Program:1. Dial53.“STATION FEATURES”
2. Dial13.“HEADSET MODE”
3. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To change setting, repeat procedure and make opposite selection.
Headset Operation As A User Function
Description:To arrange for headset operation at a user’s telephone ( DigiTech models 7700S, rev. I
and later,Impactmodel 8024S, and Impression models 20nnn and 21nnn) you must
program a headset button at the LCD speakerphone to activate the headset option.
To Program:1. PressINTERCOMat the user’s telephone.
2. DialSS1.
3. Select button to be programmed.
—PressA1–A14,B1–B10.
4. Dial94.
5. PressSPEAKERto end.
NOTE:On Impression telephones (models 20nnn and 21nnn) you must disconnect
the handset and plug the headset cord in its place.
Digital Telephone SystemIMI66–107
3 – 64 System Programming 
						

							3.7.17 Interactive Buttons
Description:The digital telephone system supports the operation of interactive buttons on all currently
produced Comdial proprietary LCD speakerphones. Interactive buttons provide users
with quick, easy access to system features and an expanded display that prompts them on
feature operation and progress. DigiTech andImpactLCD speakerphones provide
interactive buttons to the user at all times; however, the DigiTech LCD speakerphones
(revision H and earlier) do not provide interactive buttons at default and you must take
this programming action to enable them.
To Program:1. Dial53.“STATION FEATURES”
2. Dial17.“SOFT KEYS”
3. Select station ports (LED on = Feature Assigned):
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station/line feature.
—OR—
DialSSfor configuration mode.
5. PressSPEAKERto end.
IMI66–107Digital Telephone System
System Programming 3 – 65 
						

							3.7.18 Idle Line Preference
Description:When you enable idle line preference, a station will automatically connect to any
assigned and idle line that you have programmed for this purpose when the user takes the
station off hook.
To Program:1. Dial54.“STA/LINE CONFIG.”
2. Dial7.“IDLE LINE PREF.”
3. Select line ports (LED On = Selected Port)
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15, 16or pressB1, B2
—Line port 17–24 = Dial17–24or press HOLD then pressA1–A8.
4. Dial # when all line ports are selected.
5. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
6. DialSwhen all station ports are selected
—OR—
dialSSfor next station/line feature
—OR—
dialSSSfor configuration mode.
To clear current setting, repeat procedure.
Digital Telephone SystemIMI66–107
3 – 66 System Programming 
						

							3.7.19 Personal Ringing Tones
Description:You can program stations to ring in one of six distinctive tones:
1. 666/571 Hz @ 16 Hz warble
2. 1000/800 Hz @ 16 Hz warble
3. 666/571 Hz @ 23 Hz warble
4. 1000/800 Hz @ 23 Hz warble
5. 500/444 Hz @ 16 Hz warble
6. 500/444 Hz @ 23 Hz warble
To Program:1. Dial53.“STATION FEATURES”
2. Dial14.“RINGING TONE”
3. Select ringing tone
—Dial1for tone 1“RINGING TONE 1”
—Dial2for tone 2“RINGING TONE 2”
—Dial3for tone 3“RINGING TONE 3”
—Dial4for tone 4“RINGING TONE 4”
—Dial5for tone 5.“RINGING TONE 5”
—Dial6for tone 6.“RINGING TONE 6”
4. Select station ports (LED On = Feature Assigned)
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor next ringing tone assignment
—OR—
pressSSfor next station feature
—OR—
PressS S Sfor configuration mode.
To change setting, repeat procedure and make different selection.
IMI66–107Digital Telephone System
System Programming 3 – 67 
						

							3.7.20 Prime Line, Prime Group, And Prime Intercom
Description:If you assign a group of lines, an intercom line, or one individual line to a particular
station for use as its prime line, the station automatically selects it for use when the user
takes it off-hook.
To Program:1. Dial53.“STATION FEATURES”
2. Dial15.“PRIME LINE ”
3a. Assign prime line“PRIME LINE XX”
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24 = Dial17–24or pressHOLDthen pressA1–A8.
3b. Assign prime group, dial51–54for groups 1–4.“PRIME LINE GRP X”
3c. Assign prime intercom, Dial50for intercom line.“PRIME INTERCOM”
4. Select station ports (LED On = Feature Assigned)
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor next prime line, group, or intercom assignment
—OR—
pressSSfor next station feature
—OR—
pressSSSfor configuration mode.
To clear current setting, repeat procedure.
3.7.21 Message Wait Originate
Description:Any station that you program with this feature can control the message waiting light at
other stations in the system. When a station user observes the message waiting light turn
on, he or she can pressINTERCOMand thenHOLDto call the station that controlled
the light.
To Program:1. Dial53.“STATION FEATURES”
2. Dial06.“MSG. WAIT ORIG.”
3. Select station ports (LED On = Feature Selected).
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To clear current setting, repeat procedure.
Digital Telephone SystemIMI66–107
3 – 68 System Programming