Comdial Impact Dsu Instructions Manual

							3.8 Button Mapping The Stations
(Non-Square System Configuration)
You can assign (map) every programmable button at each digital station to be line-select buttons so that
they provide access to outside lines; to be direct station select (DSS) buttons so that they provide quick
access to system stations; to be special purpose buttons so that they provide telephone users with
one-button access to features; or to be idle buttons so that they provide autodial locations for the station
user.
Three idle (unmapped) buttons serve as dynamic line buttons. Dynamic line buttons provide a location for
the system to temporarily assign a line appearance to a station that normally does not have that particular
line assigned to it. While a line is in appearance there, the user can perform any normal call handling
operations that he or she wishes to perform. The lines are identified as follows: B1, B2, and B3 on
DigiTech telephones (product codes 7700S, 7714X, and 7114S), B1, B2, and B3 on Impression
telephones (product codes 2022S, 2122S, 2122X, and 2101N), or L1, L2, and L3 onImpacttelephones
(product codes 8012S, 8024S, 811N, 8112S, and 8124S). Refer to section 4.4,Recording The Station
Configurations, for button illustrations.
When you map a button at a station port, press the corresponding button on the programming station to
select the button to be mapped. If you must map buttons at a station port while using a programming
telephone that does not provide a full complement of buttons, you can dial a 3-digit code to select a
button. The table below lists the 3-digit codes and their corresponding buttons.
Table 3–8: Button Codes For DigiTech And
ImpactTelephones
Code Impression DigiTechImpact
120 A1 A1 L01
118 A2 A2 L02
116 A3 A3 L03
114 A4 A4 L04
112 A5 A5 L05
110 A6 A6 L06
108 A7 A7 L07
121 A8 A8 L08
119 A9 A9 L09
117 A10 A10 L10
115 A11 A11 L11
113 A12 A12 L12
111 A13 A13 L13
109 A14 A14 L14
122 A15 B9 L15
123 A16 B10 L16
100 B1 B1 L17
101 B2 B2 L18
102 B3 B3 L19
103 B4 B4 L20
104 B5 B5 L21
105 B6 B6 L22
106 B7 L23
107 B8 L24
IMI66–107Digital Telephone System
System Programming 3 – 79 
						

							Digital Telephone SystemIMI66–107
3 – 80 System Programming 
						

							3.8.1 Account Code Button
Description:Press the account code button and then dial an account code to record a call into a
particular category without interrupting the call.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial17. “ASSIGN ACCT KEY ”
3. Select button to be programmed
—PressA1–A14, B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or dialC10–C57.
5. DialSfor further ACCOUNT CODE button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor next configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
IMI66–107Digital Telephone System
System Programming 3 – 81 
						

							3.8.2 Automatic Call-Back Button
Description:When a user presses this button after they encounter a busy tone, the system will
automatically ring both the called station and the user’s station when the called station
becomes idle.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial10.“ASSIGN CALL BACK”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57: Dial10–57or pressC10–C57.
5. DialSfor next AUTO CALL-BACK button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
3.8.3 Blank Buttons
Description:Blank those buttons that you want to be dynamic line buttons or autodial buttons.
NOTE:When blanking buttons, be sure a previously assigned button is idle (feature
not selected by user) before you blank it.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial04.“BLANK/AUTODIAL”
3. Select all buttons to be programmed
—PressA1–A14,B1–B10.
4. Dial #.
5. Select station ports (LED On = Selected).
—Station 10–57 = Dial10–57or pressC10-C57.
6. DialSfor further button blanking
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
Digital Telephone SystemIMI66–107
3 – 82 System Programming 
						

							3.8.4 Call Forward Button
Description:This button provides one-button forwarding of all calls to another extension.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial11. “ASSIGN CALL FWD ”
3. Select button to be programmed
—PressA1–A14, B1–B10.
4. Select station ports (LED On = Selected).
—Station 10–57 = Dial10– 57or pressC10–C57.
5. DialSfor next CALL FORWARD button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
3.8.5 Call Park Orbit Button
Description:The call park orbit button will automatically park an active call in orbit when the user
presses it.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial12.“ASSIGN CALL PK”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Dial1–9for parking orbit 1–9.“ASSIGN CALL PK X”
5. Select station ports (LED On = Selected).
—Station 10–57: Dial10–57or pressC10–57.
6. DialSfor next CALL PARK ORBIT button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment, dial5604, press button, dial#select station, and dialSSS.
IMI66–107Digital Telephone System
System Programming 3 – 83 
						

							3.8.6 Do Not Disturb (DND) Button
Description:Pressing the DND button prevents other stations from calling the DND station.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial07.“ASSIGN DND CODE”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor further DND button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial # select station, and dialSSS.
3.8.7 DSS/BLF Button
Description:DSS buttons provide quick access to system stations and their lights and show the busy
status of the monitored stations.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial03.“ASSIGN DSS/BLF”
3. Select button to be programmed
—PressA1–A14, B1–B10.
4. Select station port (LED On = Selected).
—Station 10–57 = Dial10–57or pressC10–C57.
5. Repeat steps 3 and 4 until all ports are assigned.
6. Dial#.
7. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or pressC10–C57.
8. DialSfor further DSS/BLF button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
Digital Telephone SystemIMI66–107
3 – 84 System Programming 
						

							3.8.8 Line Button
Description:Line select buttons provide access to outside lines.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial02.“ASSIGN LINE”
3. Select button to be programmed:
—PressA1–A14, B1–B10.
4. Select line ports to be assigned.
—Line port1–14= Dial01–14or PressA1–A14
—Line port15, 16 =Dial15–16or PressB1, B2
—Line port17–24= Dial17–24or pressHOLDthen pressA1–A8.
5. Repeat steps 3 and 4 until all lines are assigned.
6.
Dial
#to finish button mapping.
7. Select station port (LED On = Selected)
—Station 10–57: Dial10–57or pressC10–C57.
8. DialSfor further LINE/BUTTON assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
3.8.9 Line Group Button
Description:This button provides one-button access to a line group.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial13.“ASSIGN LINE GRP”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Dial1–4for line group 1–4.“ASSIGN LINE GRP X”
5. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or pressC10–C57.
6. DialSfor next LINE GROUP button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment, dial5604, press button, dial#select station, and dialSSS.
IMI66–107Digital Telephone System
System Programming 3 – 85 
						

							3.8.10 Line Group Queue Button
Description:A station user can queue for a busy line by pressing a line group queue button.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial15.“ASSIGN LINE GRP Q”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Select station ports (LED On = Selected).
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor next LINE GROUP QUEUE button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment, dial5604, press button, dial#select station, and dialSSS.
3.8.11 Multiple Intercom Button
Description:You can assign a second intercom button to stations that may make many intercom calls.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial05.“ASSIGN 2ND INTERCOM ”
3. Select button to be programmed:
—PressA1–A14,B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57: Dial10–57or pressC10–C57.
5. DialSfor further MULTIPLE INTERCOM button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment, dial5604, press button, dial#select station, and dialSSS.
Digital Telephone SystemIMI66–107
3 – 86 System Programming 
						

							3.8.12 Privacy Button
Description:A user engaged in a private call can press the privacy button to change a current call into
a non-private one.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial06.“ASSIGN PRIVACY ”
3. Select button to be programmed
—PressA1–A14, B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57: Dial10–57or pressC10–C57.
5.DialSfor further PRIVACY button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
3.8.13 Save Button
Description:A telephone user can press the SAVE button to store the last dialed number for later
redial.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial08.“ASSIGN SAVE”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor further SAVE button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment, dial5604, press button, dial#select station, and dialSSS.
IMI66–107Digital Telephone System
System Programming 3 – 87 
						

							3.8.14 Voice Announce Block Button
Description:Telephone users can block voice announced intercom calls and station paging by pressing
this button.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial14.“ASSIGN V. A. B.”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor next VOICE ANNOUNCE BLOCK button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment , dial5604, press button, dial#select station, and dialSSS.
3.8.15 Zone Page/All-Call Button
Description:This button will provide a station with one-button access to all-call and zone paging.
To Program:1. Dial56.“BUTTON MAPPING ”
2. Dial09.“ASSIGN ZONE”
3. Select button to be programmed
—PressA1–A14,B1–B10.
4. Dial1–3for zone 1–3“ASSIGN ZONE X”
—OR—
dial4for all-call.“ASSIGN ALL CALL ”
5. Select station ports (LED On = Selected)
Station 10–57 = Dial10–57or pressC10–C57.
6. DialSfor further paging button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear assignment, dial5604, press button, dial#, select station, and dialSSS.
Digital Telephone SystemIMI66–107
3 – 88 System Programming