Comdial Impact Dsu Instructions Manual

							3.7.2 All-Call and Zone Paging
You can program the system so that the users can make announcements to stations located in certain areas
of the site or to all of the stations. Similarly, you can program a station with one-button access to the
paging feature.
Assign All-Call Or Zone Paging Feature
Description:Telephone users can receive voice announcements through their telephone loudspeakers,
or through an external paging amplifier and speaker connected to a PA port. They can
transmit these voice announcements with their telephone handsets. You can arrange the
programming so that the users can make announcements to stations located in certain
areas of the site or to all of the stations. By default, All-Call Originate and Receive is
available to all stations.
To Program:1. Dial55.“PAGING”
2. Choose paging assignment
—Dial1for zone 1 originate“ORIGINATE ZONE 1”
—Dial2for zone 2 originate“ORIGINATE ZONE 2”
—Dial3for zone 3 originate“ORIGINATE ZONE 3”
—Dial4for all-call originate“ALL-CALL ORIG.”
—Dial5for zone 1 receive“RECEIVE ZONE 1”
—Dial6for zone 2 receive“RECEIVE ZONE 2”
—Dial7for zone 3 receive“RECEIVE ZONE 3”
—Dial8for all-call receive“ALL-CALL RECEIVE”
—Dial9to clear all assignments.“CLEAR PAGING”
3. Select station ports (LED On = Feature Active).
—Station 10–57 = Dial10–57or pressC10–C57.
4. DialSto assign other paging
—OR—
dialSSfor configuration mode.
To change setting, repeat procedure and make different selection.
IMI66–107Digital Telephone System
System Programming 3 – 49 
						

							Assign All-Call and Zone Paging Button
Description:If you wish, you can assign a paging button to provide a station with one-button access to
the all-call and zone paging feature.
To Program:1. Dial56. “BUTTON MAPPING ”
2. Dial09.“ASSIGN ZONE”
3. Select button to be programmed (LED On = Paging Button).
—PressA1–A14,B1–B8.
4. Dial1–3for zone 1–3“ASSIGN ZONE X ”
—OR—
dial4for all-call.“ASSIGN ALL CALL ”
5. Select station ports (LED On = Button Assigned To Port)
—Station 10–57: Dial10–57or pressC10–C57.
6. DialSfor further paging button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor configuration mode.
To clear a paging button, dial5604, press paging button, dial#,and repeat steps 5 and 6.
Digital Telephone SystemIMI66–107
3 – 50 System Programming 
						

							3.7.3 Audible Monitoring
The DSS/BLF at a multiline station provides a visual indication of idle, busy, and ringing status of the
monitored stations. You can also provide audible indication of direct and delayed ringing for selected
stations; however, you must first enable the station monitoring feature on a system-wide basis.
Enable Audible Monitoring
Description:Enable audible monitoring on a system-wide basis using this feature.
To Program 1.Dial20.“MONITOR XXXXXXX”
2. PressA1to switch between enable and disable (LED On = Enable)
—OR—
dial1to Enable“MONITOR ENABLED”
dial2to Disable.“MONITOR DISABLED”
3. DialSfor configuration mode.
To change setting, repeat procedure and make opposite selection.
Assign Audible Monitoring To Stations
Description:Once you have enabled audible monitoring system wide, you must select each station and
the type of audible monitoring that you want to program.
To Program:1. Dial53.“STATION FEATURES”
2. Dial20.“AUDIBLE MONITOR ”
3. Select monitoring type.
—Dial1for no audible monitoring“NONE”
—Dial2for direct ring monitoring“DIRECT RING”
—Dial3for delayed ring monitoring. “DELAYED RING ”
4. Select stations ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
5. DialSnext monitoring condition
—OR—
dialSSfor next station feature
—OR—
dialSSSfor configuration mode.
To change setting, repeat procedure and make different selection.
IMI66–107Digital Telephone System
System Programming 3 – 51 
						

							3.7.4 Automatic Hold
You can give station users the ability to place an existing line or intercom call on hold when she or he
presses another line button.
Automatic Hold With Line Calls
Description:When you enable this feature, the telephone user can automatically place an existing line
call on hold when she or he presses another line button to answer a second call.
To Program:1. Dial53.“STATION FEATURES”
2. Dial11.“AUTO HOLD ”
3. Select station ports (LED On = Feature Assigned).
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To clear current setting, repeat procedure.
Automatic Hold With Intercom Calls
Description:If you want the telephone user to also have the automatic hold feature while he or she is
on an existing intercom call and presses another intercom button or a line button, take
this additional programming action.
To Program:1. Dial53.“STATION FEATURES”
2. Dial12.“ITCM AUTO HOLD”
3. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To clear current setting, repeat procedure.
Digital Telephone SystemIMI66–107
3 – 52 System Programming 
						

							3.7.5 Automatic Privacy
You can make a line private or non-private. In the private mode, a station has exclusive use of a line
during a call. You can arrange for individual stations to automatically release privacy while on private
lines.
Make A Line Private Or Non-Private
Description:Use this feature to make a particular line private or non-private.
To Program:1. Dial40.“PRIVACY RELEASE ”
2. Select line ports to be non-private (LED On = Non Private Port)
—Line port 1–14 = Dial01–14or PressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24 = Dial17–24or pressHOLDthen pressA1–A8.
3. DialSfor configuration mode.
To clear current setting, repeat procedure.
Arrange Station To Automatically Release Privacy On Private Line
Description:You can arrange for individual stations to automatically release privacy while on private
lines. With this arrangement, other stations can join the programmed station whenever it
is on the line that you have assigned as a privacy release line.
To Program:1. Dial54.“STA/LINE CONFIG.”
2. Dial4.“PRIVACY RELEASE”
3. Select privacy release line ports (LED On = Selected Ports).
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24 = Dial17–24or pressHOLDthen pressA1–A8.
4. Dial#when all line ports are selected.
5. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
6. DialSwhen all station ports are selected
—OR—
dialSSfor next station/line feature
—OR—
dialSSSfor configuration mode.
To clear current setting, repeat procedure.
IMI66–107Digital Telephone System
System Programming 3 – 53 
						

							3.7.6 Call Forward On Busy/Ring–No Answer
The system can automatically forward busy and ring-no answer calls to a new station. The system sends
these calls to any idle station associated either by intercom hunt group or by department with the called
station. Use this feature to arrange for calls to cycle rapidly through such associated stations by testing
each one in turn with several rings.
Enable Call Forwarding
Description:Enable call forwarding for individual stations using this feature.
NOTE:If you enable this feature, also program the system intercom signaling as
tone for the first choice.
To Program:1. Dial53.“STATION FEATURES”
2. Dial21.“CALL FWD RNA”
3. Dial0–9for 0–9 rings before forwarding.“RING S= X”
4. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
5. DialSfor additional station ring assignments
—OR—
dialSSfor next station feature
—OR—
dialSSSfor configuration mode.
To remove call forwarding from a station, assign 0 rings.
Set Tone First Intercom Signaling
Description:You must set the first choice intercom signaling method to tone first to ensure forwarding
of calls that encounter a busy signal or ring with no answer.
To Program:1. Dial16.“XXXXX ANN. FIRST”
2. PressA1to toggle from Voice To Tone (LED Off = Tone)
—OR—
dial2for Tone First.“TONE ANN. FIRST”
3. DialSfor configuration mode.
To change setting, repeat procedure and make opposite selection.
Digital Telephone SystemIMI66–107
3 – 54 System Programming 
						

							Intercom Hunt Group
Description:You can link stations together to form intercom hunt groups. Calls to a busy station in a
hunt group will search the group for an idle station to ring.
To Program:1. Dial53.“STATION FEATURES”
2. Dial18.“HUNT LINK”
3. Select first linking station
— Station 10–57 = Dial10–57or pressC10–C57.
4. Select second linking station
—Station 10–57 = Dial10–57or pressC10–C57.
5. DialSfor another link
(Example A: 17 to 16, 18 to 16 and 19 to 16)
(Example B: 16 to 17, 17 to 18, and 18 to 16)
—OR—
dialSSfor next station feature
—OR—
dialSSSfor configuration mode.
To clear current setting, hunt link station to itself.
IMI66–107Digital Telephone System
System Programming 3 – 55 
						

							3.7.7 Call Origination Denied
Description:You can deny users of selected stations the ability to originate calls on specified lines.
This feature does not prevent the user from answering incoming calls on these lines.
To Program:1. Dial54.“STA/LINE CONFIG.”
2. Dial6.“ORIGINATION DENY”
3. Select line ports (LED On = Selected Ports).
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24 = Dial17–24or pressHOLDthen pressA1–A8.
4. Dial#when all line ports are selected.
5. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
6. DialSwhen all station ports are selected
—OR—
dialSSfor next station/line feature
—OR—
dialSSSfor configuration mode.
To clear current setting, repeat procedure.
3.7.8 Central Message Desk
Description:Use this feature to designate one station in the system as the central message desk. When
you do this, the system automatically arranges for the central message desk station to
have message wait originate capability so that it can control message waiting lights at
other stations.
To Program:1. Dial53.“STATION FEATURES”
2. Dial08.“MSG DESK”
3. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To clear current setting, repeat procedure.
Digital Telephone SystemIMI66–107
3 – 56 System Programming 
						

							3.7.9 Data Security Port
Description:While port is active on a call, this feature prevents any incoming tones associated with
other system features from interrupting the call.
To Program:1. Dial53.“STATION FEATURES”
2. Dial26.“DATA SECURE PORT”
3. Select station port (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To clear current setting, repeat procedure.
3.7.10 Dual Console Feature
Description:The dual console feature allow users to have two DSS/BLF consoles to complement one
telephone.
To program: 1.Dial53for station features.“STATION FEATURES”
2. Dial34to enable second console.“SECOND CONSOLE ”
3. Select console port
—Station 10–57: Dial10–57or pressC10–C57.
4. Select station port that console is to complement
—Station 10–57: Dial10–57or pressC10–C57.
5. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To clear second-console assignment, perform the following steps:
(a)  Repeat steps 1 through 3 above
(b) Type console port number twice
(c)  DialS Sfor configuration mode.
IMI66–107Digital Telephone System
System Programming 3 – 57 
						

							3.7.11 Executive Override
Description:You can provide selected stations with busy override. This feature allows the station to
override a busy condition at a station, sound a warning tone, and gain access to the
existing conversation.
To Program:1. Dial53. “STATION FEATURES”
2. Dial02.“EXEC. OVERRIDE ”
3. Select station ports (LED On = Feature Assigned)
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
DialSSfor configuration mode.
To clear current setting, repeat procedure.
Digital Telephone SystemIMI66–107
3 – 58 System Programming