Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

							APPPENDIX A: Voice and fax boards133
DB-37 pinouts
Pin 37 is the ground.
Pins 17, 34, 35, and 36 are unused.
Continued Line number Tip connection Ring connection
1 Pin 1 Pin 18
2 Pin 2 Pin 19
3 Pin 3 Pin 20
4 Pin 4 Pin 21
5 Pin 5 Pin 22
6 Pin 6 Pin 23
7 Pin 7 Pin 24
8 Pin 8 Pin 25
9 Pin 9 Pin 26
10 Pin 10 Pin 27
11 Pin 11 Pin 28
12 Pin 12 Pin 29
13 Pin 13 Pin 30
14 Pin 14 Pin 31
15 Pin 15 Pin 32
16 Pin 16 Pin 33 
						

							UNITY INSTALLATION GUIDE134
Dialogic D/160SC-LS 
Continued
voice boardHardware settingsDo the following procedures as you install voice boards.
To set the SW100 switch
For each Dialogic ISA voice board that has a rotary switch, 
set the rotary switch to a unique value starting with 0 and 
continuing in sequence. 
For example, set the rotary switch on the first three ISA 
voice boards in the Unity server as shown below. This is also 
the order in which you install the boards in the server. 
To  s e t  t h e  S W 4  s w i t c h
Set switch SW4 to “Off hook” on all boards as shown below.
First ISA board
Second ISA board
Third ISA board0
1
2
Off hook 
						

							APPPENDIX A: Voice and fax boards135
Software settings
During Unity Setup, do the following procedure when the Dia-
logic D/SC Configuration dialog box appears. 
To enter Dialogic settings during Unity Setup
aChange the value of “BLTInterrupt” to “5.”
bChange the value of “BLTAddress” to the appropriate value:
Turnkey systemSelect “D0000.”
Component systemSelect the address that you reserved 
during the procedure “To find and reserve memory 
addresses and an IRQ (ISA boards in a component system 
only),” on page 35.
cClick “OK” to continue.
dReturn to the procedure that you were doing when the Dia-
logic D/SC Configuration dialog box appeared. 
						

							UNITY INSTALLATION GUIDE136
Dialogic 
D/240PCI-T1 
voice boardSwitch SW100
To p  v i e w
Side view
Voice board 
backplate
LED status
indicators
T1 trunk
interfaceO
N1
Pin 1: Receive ring
Pin 2: Receive tip
Pin 3: Chassis ground
Pin 4: Transmit ring
Pin 5: Transmit tip
Pin 6: Chassis ground
Pin 7: Chassis ground
Pin 8: Chassis ground
Connection pinouts
The D/240PCI-T1 uses an 
RJ-48C connector.
JP2–JP7CT bus connector 
						

							APPPENDIX A: Voice and fax boards137
Hardware settings
Do the following procedures as you install voice boards.
To set the SW100 switch
For each Dialogic PCI voice board that has a rotary switch, 
set the switch to a unique value starting with 1 and con-
tinuing in sequence. For example, set the switch on the first 
three PCI voice boards in the Unity server as shown below. 
Install the boards in the server in the same order. 
To set jumpers JP2 to JP7
Set jumpers JP2 to JP5 to “Off” on each board. For jumpers 
JP6 and JP7, install shunts on the top two pins (1 and 2). 
Software settings
None.
LED status indicators
The D/240PCI-T1 includes the following status indicators.
First PCI board
Second PCI board
Third PCI board
JP2 JP3 JP4 JP5 JP6 JP7
Setting
Color Lit
Green The board is powered up and receiving an external signal
Yellow Loss of frame synchronization at far end external network
Red Loss of frame synchronization on incoming line from external 
network1
2
3 
						

							UNITY INSTALLATION GUIDE138
Dialogic 
GammaLink 
CP4/LSI 
Series 1 
fax board
Pin 3: First fax line tip Pin 2: First fax line ring
Connection pinouts
The CP4/LSI Series 1 
uses RJ-11 connectors.
Pin 1: Second fax line tip
Pin 4: Second fax line ring
Pin 3: Third fax line tip Pin 2: Third fax line ring
Pin 1: Fourth fax line tip
Pin 4: Fourth fax line ringSwitch block SW1
Side view
Fax board backplate
Lines 3 & 4
Lines 1 & 2
LED status indicators
Switch block SW1
Side view 
						

							APPPENDIX A: Voice and fax boards139
Hardware settings
Do the following procedure as you install fax boards.
To  s e t  s w i t c h  b l o c k  S W 1
The switch block SW1 settings determine the fax ports’ I/O 
addresses.
The CP4/LSI Series 1 board contains four fax ports. Depending 
on the configuration of the Unity server and on whether Active-
Fax is installed on a separate server, you can install up to eight 
CP4/LSI Series 1 boards.
Set the SW1 switches on each board as shown below.
LED status indicators
There are two LED status indicators for each fax port. The fol-
lowing table describes the meaning of the status indicators.
SW1
switchSW1
switch
First board
Ports 0–3Fourth board
Ports 12–15
Second board
Ports 4–7Fifth board
Ports 16–19
Third board
Ports 8–11Sixth board
Ports 20–23
Color Lit Unlit Blinking
Green Port is off hook Port is on hook ---
Amber Board is 
operationalBoard is not 
operationalBoard configuration 
problem
On
Off
123
On
Off
123
On
Off
123
On
Off
123
On
Off
123
On
Off
123 
						

							UNITY INSTALLATION GUIDE140
Dialogic 
GammaLink 
CP4/LSI 
Series 2 
(CPi/400) 
fax board
Pin 3: First fax line tip Pin 2: First fax line ring
Connection pinouts
The CP4/LSI Series 2 
uses RJ-11 connectors.
Pin 1: Second fax line tip
Pin 4: Second fax line ring
Pin 3: Third fax line tip Pin 2: Third fax line ring
Pin 1: Fourth fax line tip
Pin 4: Four th fax line ringLED status indicators
Rotar y switch
Fax board backplate
Lines 3 & 4
Lines 1 & 2
Side view 
						

							APPPENDIX A: Voice and fax boards141
The CP4/LSI Series 2 fax board is also known as the CPi/400.
Hardware settings
Do the following procedure as you install fax boards.
To set the rotary switch
The rotary switch setting determines the fax ports’ I/O 
addresses.
The CP4/LSI Series 2 board contains four fax ports. Depending 
on the configuration of the Unity server and on whether Active-
Fax is installed on a separate server, you can install up to eight 
CP4/LSI Series 2 boards.
Set the rotary switch on each board as shown below.
LED status indicators
There are two LED status indicators for each fax port. The fol-
lowing table describes the meaning of the status indicators.
Rotary
switchRotary
switch
First board
Ports 0–3Fourth board
Ports 12–15
Second board
Ports 4–7Fifth board
Ports 16–19
Third board
Ports 8–11Sixth board
Ports 20–23
Color Lit Unlit Blinking
Green Port is off hook Port is on hook ---
Amber Board is 
operationalBoard is not 
operationalBoard configuration 
problem
03
14
25 
						

							UNITY INSTALLATION GUIDE142
Dialogic 
GammaLink 
CPD/220 
fax board
Fax board backplate
Pin 3: Tip 1 Pin 2: Ring 1
DID cable (miniature jack)
Miniature 
jack
Pin 1: Ring 2
Pin 4: Tip 2RJ-11 
wall jack
LED status indicators
Pin 1: Ring 2
Pin 2: Ring 1
Pin 3: Tip 1
Pin 4: Tip 2
Switch block 
SW1
LSI cable (RJ-11 wall jack)
Side view