Trillium Panther Ii Feature Module Iv System Manual

							Trillium Standard  Practice 
To MDF 
stations:  24 
Vdc  Battery 
AC  Power  Backup 
s 
_~lllli~lllllllllllllllll~ll 
4  0 
IIIIIIIIIIIIIIIIIIIIIIIII 
IIbdhn 
-18to25  KEY Background 
Music 
Music  on Hold 
AmDlifier 
I  Feature  Module Cartridge 
e  Power  Fail 
Station 
M:yge  I 
rl 
. 
Answer 
Door  Unit 
Module 
Dl 02 
DA 
Incoming  - 
$%xBW  Lines  
(1  -8) 
!53 
Printer  / Terminal 
Figure  6-l (a)  Panther  II 820  Main  Configuration 
Installation  and Commissioning 
Page  12  
						

							Panther II 820/1032/2064-200 
A 
a 
T 
24 Vdc Battery 
AC Power Backup 
To MDF 
stations: 
Back round Music 
Music on Hold 
I Feature Module Cartridge 
II Door 
III III 
Station 
MreTtt 
Recorder Connect to 
Panther 2064 
Cabinet or 
connect to 
6 C.O. Line 
Module, if 
applicable 
I 
Incoming 
C.O./PBW 
Centrex Lines 
(1 
- 10) 
II I I 
557 
To Printer/Terminal 
Figure 6-l(b) Panther II 1032 Main Configuration 
Installation and Commissioning 
Page 13  
						

							Trillium Standard Practice 
To MDF 
stations: 
AC Pnwer 24 Vdc Battery L’ I 
Backup 
, ._ . __._. 
I 
~lllllllllllllllllllli L 
KEY 
SEURNL;FE Power Fail 
Connect to 
Panther 1032 
Cabinet 
1 I= -ill Incoming 
C.O./PBX/ 
Centrex Lines 
(11 -20) 
Figure 6-l(c) Panther II 2064 Main Configuration 
Installation and Commissioning 
Page 
14  
						

							Panther II 820/1032/2064-200 
Mounting System Components 
6.0 4 The following instructions detail the installation of the KSU. The installation 
procedure is similar for any ancillary devices included in the system, only the location 
of the mounting screws may differ. This can be seen in Figures 6-2 to 6-6. 
Step 1. 
Using suitable fasteners, mount a wooden backboard, of sufficient size 
to accommodate the KSU and ancillaq devices (if any), to the wall, 
within 4 feet of the ac outlet and at least 12 inches (305 mm) above the 
floor. Allow room for installation of the ancillary devices which may be 
installed at a later date. 
Step 2. Position the KSU on the backboard. Mark the positions of the KSU’s 
four mounting screws on the backboard. 
Step 3. Install the mounting screws supplied, into the backboard, leaving 
approximately an 0.2 inch (5 mm) gap between the back of the screw 
head and the backboard. 
Step 4. 
Hang the KSU on the mounting screws. Tighten the mounting screws. 
Caution: Do not connect the KSU power cord until instructed to do so. I 
Step 5. Repeat Steps 1 through 4 for each of the ancillary devices to be 
installed. 
Installing the Feature Module Cartridge 
6.0 
5 Panther II 820 and 1032 Key Service Units have a Feature Module Cartridge 
that contains the software for the Panther II features. 
Step 1. Unpack the Feature Module Cartridge. An information sheet packed 
with the Feature Module Cartridge provides an installation diagram. 
Step 2. There are two small grooves on the Feature Module Cartridge 
connector. Holding the Feature Module Cartridge so that the grooves 
are facing you, plug it into the port that is located halfway down the 
right-hand side of the KSU. 
Step 3. Place the protective cover over the Feature Module Cartridge, push in 
the plastic expander plugs, and tighten the two screws. 
Installation and Commissioning 
Page 15  
						

							Panther II 820/1032/2064-200 
t 
17.8 cm 
(7 inch) 14.9 cm 
(5.875 inch) 
Wooden 
Backboard 
Door 
/ Answer 
Unit 
Figure 6-3 Door Answer Unit Wall Mounting 
Installation and Commissioning 
Page 17  
						

							Trillium Standard Practice 
--. 
7.9 cm 
(3.125 inch) 
-1 Wooden 
8.9 cm 
(3.5 inch) Power 
Fail 
Transfer 
Unit 
Figure 6-4 Power Fail Transfer Unit Wall Mounting 
Installation and Commissioning 
Page 18  
						

							Panther II 820/1032/2064-200 
7.9 cm 
( 3.11 inch) 
r-7 Wooden 
t n 1- 
-. -. 
. . 
-. Station 
Message 
Detail 
Recording 
Unit 
J Ull 
(3.56 inch) 
Figure 6 -5 SMDR Unit Wall Mounting 
Connect The Equipment To Ground 
6.0 6 The 
KSU must be connected to ground through a single solid conductor. 
Caution: DO NOT rely on the third wire (Green) of the AC cord to connect 
the 
KSU to ground. A separate external ground lead must be connected. 
Installation and Commissioning 
Page 19  
						

							Panther II 820/1032/2064-200 
Step 2. 
When the system comprises a 2064 KSU, repeat Step 1 for CO. lines 
11 through 20. When a second Door Answering Unit forms part of the 
system configuration, do not connect C.O. line 20. 
Line Lead Designation Conductor Color MDF Terminal RJ21 Pin Number 
1 Tip White-Blue 1 26 
Ring Blue-White 2 1 
2 Tip White-Orange 3 27 
Ring Orange-White 4 2 
3 Tip White-Green 5 28 
Ring Green-White 6 3 
4 Tip White-Brown 7 29 
Ring Brown-White 8 4 
5 Tip White-Slate 9 30 
Ring Slate-White 10 5 
6 Tip Red-Blue 11 31 
Ring Blue-Red 12 6 
7 Tip Red-Orange 13 
32 
Ring Orange-Red 14 7 
8 Tip Red-Green 15 
33 
Ring Green-Red 16 8 
9 Tip Red-Brown 17 
34 
Ring Brown-Red 18 9 
10 Tip Red-Slate 19 
35 
Ring Slate-Red 20 10 
DO NOT connect line 8 if the Door Answer Unit is being installed on the Panther II 820 system. 
DO NOT connect line 10 if the Door Answer Unit is being installed on the Panther II IO32 system. 
*Not required for the Panther II 820 system. 
Table 6-l Pin-to-Pin Designations 
(for Panther II 820/1032 KSU) 
(RJ21X Connector) 
Installation and Commissioning 
Page 21