Trillium Panther Ii Feature Module Iv System Manual

							Panther II 820/1032/2064-205 
Not Used on Panther II 1032 System 
. 
TABLE 2-1,7 
FLEXIBLE 
RINGING 
ASSIGNMENT 
Panther II 
1032 System 
Programming 
Page 41  
						

							TrilIium Standard Practice 
TABLE 
2-14 
FLEXIBLE 
RINGING 
ASSIGNMENT 
Panther II 
2064 System 
Use all of Table 
2-13 (for the first 
32 stations), and 
this chart (for the 
remaining 32 
stations) to fill 
in which lines 
will ring at each 
station. 
Programming 
Page 
42  
						

							Panther II 820/1032/2064-205 
GROUP PROGRAMMING 
General by Line 
2.2 0 The 
Group Parameters, including Access Codes and Data Codes are provided in 
Tables 2-15 to 2- 18. The parameters are: 
TENANT GROUP ASSIGNMENT: Up to 8 lines on the Panther 
II 820 system, or 10 lines on the Panther II 1032 system, or 20 lines 
-on the Panther II 2064 system are put into one of 15 Tenant Groups. 
Use Table 2-15 to check off which lines are to be included in each 
group from 01 to 15. Note: A line can be in more than one tenant 
group. 
2.2 
1 After filling in your Tenant Group Assignment selections in Table 2-15: 
Step 1. At Station 10 (using a Panther II Display Set), dial * # 0 1 5. 
Step 2. Dial 20122 (where 22 is a 2-digit group number from 01 to 
15). 
Step 3. 
Step 4. Dial XX (where XX is a 2-digit line number from 01 to 20). 
Dial the digit 1, if you want the selected line in the selected 
group, 
OR 
Dial the digit 0, if you do not want the selected line in the 
selected group. 
Step 5. After the inputted data is displayed, press the HOLD key to 
store the data and increment to the next line. 
Step 6. Repeat Steps 4 and 5 until all lines in a particular group are 
programmed, then 
l Press the HOLD key to increment to the next group number, 
OR 
l Press # to store all previous data or dial a new access code. 
Step 7. 
Press the *key to exit programming when all selections have 
been made. The new programming is complete. 
Programming 
Page 43  
						

							Trillium Standard Practice 
TABLE 2-15 (a) TENANT GROUP ASSIGNMENT 
-. 
:) ,’ 
TABLE 2-15 (b) TENANT GROUP ASSIGNMENT 
Programming 
Page 44  
						

							Panther II 820/1032/2064-205 
LINE POOLING GROUPS: Up to 8 lines on the Panther II 820 
system, or 10 lines on the Panther II 1032 system, or 20 lines on the 
Panther II 2064 system are put into one of four Pool Groups. 
Use 
Table 2-16 to check off which lines are to be included in each group 
from 01 to 04. 
Note: Only “like” lines should go into a line pool (e.g., a pool is made up of all 
“same area” WATS lines, local lines, FX lines, and so on). The same line will not 
be in more than one line pool group. Pool groups should be organized so [hat there 
is one primary line pool with an unlimited number of lines, and three other pool 
groups. 
* To enable LINE POOLS as PROGRAMMABLE KEYS 
(on individual SetS), refer to Subsection 3. 
2.2 1 After filling in your Line Pooling Group selections in Table 2- 16: 
Step 1. 
Step 2. 
Step 3. At Station 10 (using a Panther II Display Set), dial * # 0 1 5. 
Dial 204RR (where RR is a 2-digit pool group number from 01 
to 04). 
Dial XX (where XX is a 2-digit line number from 01 to 20). 
Step 4. Dial the digit 0, if you do not want the selected line in the 
selected pool group, 
OR 
Dial the digit 1, if 
you want the selected line in the selected pool 
group. 
Step 5. After the inputted data is displayed, press the HOLD key to 
store the data and increment to the next line. 
Step 6. Repeat Steps 4 and 5 until all lines in a particular line pool are 
programmed, then 
l Press the HOLD key to increment to the next pool number, 
OR 
l Press # to store all previous data or dial a new access code. 
Step 7. Press the * key to exit programming when all selections have 
been made. The new programming is complete. 
Programming 
Page 45  
						

							Trillium Standard Practice 
TABLE 2-16 LINE POOLING GROUPS 
LINES 
POOL 
GROUP 
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 2C 
01 / /’ /’ 
02 
03 
lo41 I I I I I I I ! I I I I I I I I I I I 
Check off each line you would like in each line pool group. 
NIGHT TRANSFER LINE GROUPS: Up to 8 lines on the 
Panther II 820 system, or 10 lines on the Panther II 1032 system, or 20 
lines on the Panther II 2064 system are put into one of four Night 
Transfer Line Groups. Use Table 2-17 to check off which lines are to 
be included in each group from 01 to 04. Note: A line can be in more 
than one Night Transfer Line Group. 
2.2 2 After filling in your Night Transfer Line Group selections in Table 2-17: 
Step 1. At Station 10 (using a Panther II Display Set), dial * # 0 1 5. 
Step 
2. Dial 203RR (where RR is a 2-digit Night Transfer Line Group 
number from 01 to 04). 
Step 3. Dial XX (where XX is a 2-digit line number from 01 to 20). 
Step 4. Dial the digit 0, if you do not want the selected line in the 
selected Night Transfer Line Group, 
OR 
Dial the digit 1, if you want the selected line in the selected 
Night Transfer Line Group. 
Programming 
Page 46  
						

							Panther II 820/1032/2064-205 
Step 5. 
Step 6. 
. 
. 
Press # to store all previous data or dial a new access code. 
Step 7. Press the * key to exit programming when all selections have 
been made. The new programming is complete.  After the inputted data is displayed, press the 
HOLD key to 
store the data and increment to the next line. 
Repeat Steps 4 and 5 until all lines in a particular group are 
programmed, then 
Press the 
HOLD key to increment to the next Night Transfer 
Line Group number, 
OR 
TABLE 2-17 NIGHT TRANSFER LINE GROUPS 
LINES 
Check off each line you would like in each Night Transfer Line Group. 
Programming 
Page 
47  
						

							Trillium Standard Practice 
PRIME LINE GROUPS: Up to 8 lines on the Panther II 820 
system, or 10 lines on the Panther II 1032 system, or 20 lines on the 
Panther II 2064 system are put into one of 15 Prime Line Groups. 
Use Table 2- 18 to check off which lines are to be included in each 
group from 01 to 15. Note: A line can be in more than one Prime Line 
group. (Refer also to PRIME LINE PREFERENCE in this 
subsection). 
To enable a PRIME LINE (at individual Sets), refer to 
PROGRAMMABLE KEYS, Subsection 3. 
2.2 3 
After filling in your Prime Line Group Assignment selections in Table 2- 18: 
Step 1. At Station 10 (using a Panther II Display Set), dial * # 0 1 5. 
step 2. 
Dial 202ZZ (where ZZ is a 2-digit group number from 01 to 
15). 
Step 3. Dial XX (where XX is a 2-digit line number from 01 to 20). 
Step 4. Dial the digit 0, if you do not want the selected line in the 
selected group, 
OR 
Dial the digit 1, if you want the selected line in the selected 
Prime Line group. 
Step 5. After the inputted data is displayed, press the HOLD key to 
store the data and increment to the next line. 
Step 6. Repeat Steps 4 and 5 until all lines in a particular group are 
programmed, then 
l Press the HOLD key to increment to the next Prime Line number, 
OR 
l Press # to store all previous data or dial a new access code. 
Step 7. Press the * key to exit programming when all selections have 
been made. The new programming is complete. 
Programming 
Page 48  
						

							Panther II 820/1032/2064-205 
TABLE 2-18 (a) Prime Line Group Assignment 
General by Station 
2.2 4 The 
Group Parameters, including Access Codes and Data Codes are provided in 
Tables 2-19 and 2-20. The parameters are: 
TENANT GROUPS: (Table 2-19) After the 8 lines on the 
Panther II 820 system, or the 10 lines on the Panther II 1032 system, 
or the 20 lines on the Panther II 2064 system have been assigned to the 
15 Tenant groups (see GROUP PROGRAMMING - General by Line), 
each station must be assigned to one of the 15 groups. 
Note: If two businesses are sharing a system and Private Mode was 
selected in Tenanting parameters, the stations available to each business 
should be placed in separate tenant groups. 
Preprogrammed Value = No Tenant Groups. 
Programming 
Page 49  
						

							Trillium Standard Practice 
- 
TABLE 2-18 (b) Prime Line Group Assignment 4 :: 
,; 
PICKUP GROUPS: (Table 2-19) In order to perform the Call 
Pickup-Local feature on the Panther II system, each station must be 
assigned to at least one of the ftiteen 2-digit pickup groups (01 to 16). 
The pickup groups should be organized so that stations in close 
physical proximity to each other are placed in the same pickup group. 
Preprogrammed Value = All stations are placed in Pickup Group 01. 
PRIME LINE PREFERENCE: (Table 2-19) If the lines have 
been assigned to the 15 Prime Line groups (using the GROUP 
PROGRAMMING - General by Line method), each station must be 
assigned to one of the 15 groups. 
Note: It is recommended that each Panther II Set (Basic Set) be set up with its 
own individual Prime Line for eary call processing. Other users, such as those 
users with Panther II Display Sets may wish to have a Prime Line, but the System 
Manager must set up this capability from the individual’s Set (using the procedure 
outlined in Subsection 3). 
Preprogrammed Value = No Prime Line Preference groups. 
Programming 
Page 50