Toshiba Strata Dk14, Dk40i, Dk424 System Record Sheets Manual

							System & Station
Program 39 – Flexible Button Assignments
Strata DK System Record Sheets 5/9967
System & Station
CO Line AppearanceLine 1~200 or CO 001~CO 
200001~
200CO line access of appearing calls.
Data
1Data Call or DATA 456 Used to place data call.
Data Release1Data Release or DRLS 454 Releases data call.
Direct Station Selection DSS#000~
#239Assigns DSS hotline keys to port number.
Directory Numbers (see following pages)
Do Not Disturb
4Do Not Disturb or DND 498 Prevents calls to station.
Door Lock 0 ~4 (DDCB/
HDCB)
1
Unlock Door 0 or DRLK 0
Unlock Door 1 or DRLK 1
Unlock Door 2 or DRLK 2
Unlock Door 3 or DRLK 3
Unlock Door 4 or DRLK 4471
472
473
474
475Momentarily unlocks door (3 or 6 seconds).
See Program 77-1 and 77-2.
Handset Off-Hook Call 
Announce
1HS-OCA 468 Activates 2-way voice path to Off-Hook Call Announce caller. (R3)
ISDN Sub-address Sub-address 467Separates the called party’s ISDN sub-address from the called 
party number. The 
 digit performs this function on standard 
telephones.
ISDN Start Start 469Initiates DK to send dialed digits to the ISDN network when this 
button is pressed from a digital or electronic telephone. Program 
*63-2 invokes the same function when the Dial Timer expires. Also 
see Tone Button in this table.
LCD Message Select LCD Msg Select or LCD M 481 Begins LCD message selection.
Message Waiting and Flash Msg Wait, Flash or MW/FL 499 Provides message waiting LED for EKT and Flash Button.
Microphone Cutoff
5Microphn Cut-off or MCO 488Sets microphone ON/OFF for incoming handsfree Directory 
Number [DN] calls.
Modem
1Modem or MODEM 455 Used to reserve modem in modem pool.
Night Transfer Tenant 13Night Transfer1 or NT1 439
Sets Tenant CO line DAY/NIGHT ring mode. Night Transfer Tenant 23Night Transfer2 or NT2 440
Night Transfer Tenant 33Night Transfer3 or NT3 441
Night Transfer Tenant 43Night Transfer4 or NT4 442
Night Transfer Lock Tenant 1 Night Lock1 or NT1 L1 431
Available with RCTUA3, RCTUBA3/RCTUBB3 or RCTUC/D3 
Release 3 or above only.
Used to lock system ringing mode: DAY, DAY2, NIGHT See 
Programs 74 and 
*36 for NT Lock Password assignments. Night Transfer Lock Tenant 2 Night Lock2 or NT2 L2 432
Night Transfer Lock Tenant 3 Night Lock3 or NT3 L3 433
Night Transfer Lock Tenant 4 Night Lock4 or NT4 L4 434
Pause
1Spd Dial Pause or PAU 495 Sets pause in Speed dial See Program 12-3.
Pause (Long)1Spd Dial Lng Pause or PAU/L 493 Sets a 10-second pause in Speed Dial.
Pooled Line Pooled Line Grp or PL301~
316Multiple CO line may appear under one button.
Privacy Privacy On Line or PRIV 453 Prevents Privacy Override (not Executive Override).
Privacy Release Privacy Release or PRV RLS 479 Changes station Privacy mode to Non-private for CO lines.
Redial Last Number 
(
Button)Redial or RDL 496 Redials the last number.
Release to Idle Release Call or RLS 476 Releases current call and makes station idle.
Release and Answer Release and Ans or RLS/ANS 466Simulates On-hook/Off-hook operation to release an existing call 
and answer new incoming/ringing call.
Save Last Dialed Number Save Last Number on SAVE 485 Saves last number dialed for future speed dial.
Speed Dial Select 
(

Button)6Speed Dial or SDS 497 Begins speed dial selection.
Station Speed Dial Codes
6SD (All DK systems)Reserves button for station speed dial. Station Speed Dial code 
ranges vary per processor:
10~

49DK14, DK40i, RCTUA

10~

49RCTUBA/BB, RCTUC/D

100~

139RCTUE/F
Table 1 Feature Button Codes for Digital, Electronic, and Strata AirLink Wireless Telephones (continued)
Button FunctionButton LabelsCodeNotes 
						

							System & Station
Program 39 – Flexible Button Assignments
68Strata DK System Record Sheets 5/99
System Speed Dial Codes6SDSpeed dial number set by station port 000. System Speed Dial 
code ranges vary per processor:
60~

99DK14, DK40i, RCTUA

600~

699RCTUBA/BB, RCTUC/D

200~

999RCTUE/F
To n e1Tone Dial Select or TONE 490 CO dial signals set to tone or pulse.
1. Unavailable to Strata AirLink handsets (RWIU/WWIS interface).
2. Picks up calls to telephones in any call pickup group to which the telephone is assigned in Program *31.
3. See Program *15 for Tenant Group assignments.
4. The Strata AirLink handset (RWIU/WWIS interface) displays DND, but no warning tone is enabled for Executive or Busy Override.
5. The Strata AirLink handset (RWIU/WWIS interface) has mute only.
6. Both wireless system handsets (RWIU and Base Station Interface Adapter) only have an internal memory Speed Dial capability.
The Strata AirLink “call” button is set using Program 39, key 01. It must be set as the PDN of 
the handset.
Strata AirLink handset buttons 1~6 when used with the FCN button are set using Program 39, 
keys 02~07 respectively.
Table 1 Feature Button Codes for Digital, Electronic, and Strata AirLink Wireless Telephones (continued)
Button FunctionButton LabelsCodeNotes 
						

							System & Station
Program 39 – Flexible Button Assignments
Strata DK System Record Sheets 5/9969
System & Station
Alert Signal Button Assignments
Station Number: _______
Station Number: _______




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Alert Signal ButtonButton Number (01~20)Speed Dial NumberAlert Signal Button Partner 
Station Number
No.Code
1 427
2 428
3 429
4 430
Alert Signal ButtonButton Number (01~20)Speed Dial NumberAlert Signal Button Partner 
Station Number
No.Code
1 427
2 428
3 429
4 430
Enter the logical port number of the 
telephone that will be assigned an 
$OHU W6LJQDO button.YYY = the Program 39 code for the 
$OHUW
6LJQDO button that should be installed.
Press the telephone button to which 
$OHU W
6LJQDO
 should be assigned. 
						

							System & Station
Program *40 – Distributed Hunt Group Member Assignments
70Strata DK System Record Sheets 5/99
Program *40 – Distributed Hunt Group Member 
Assignments
Processor Type:DK14, DK40i, all RCTUs
Program Type:Station
Initialized Default:No member (station port) assigned to any DH Group




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
ProcessorDH Port RangeHunt Port RangeProcessorDH Port RangeHunt Port Range
DK14 900~915 000~009 RCTUBA/BB 900~915 000~079
DK40i 900~915 000~027 RCTUC/D 900~915 000~239
RCTUA 900~915 000~031 RCTUE/F 900~915 000~335
DH Port 
(900~915)Hunt Order 
(01-32)Hunt Port 
NumberDH Port 
(900~915)Hunt Order 
(01-32)Hunt Port 
NumberDH Port 
(900~915)Hunt Order 
(01-32)Hunt Port 
Number
SELECT = Distributed Hunt (DH) 
Group Number (see legend)
Hunt order (01~32)DATA = Hunt Port Number
When editing the data field, use LED 
Button 01 to delete a number. 
						

							System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
Strata DK System Record Sheets 5/9971
System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
Processor Type:RCTUBA/BB, RCTUC/D and RCTUE/F
Program Type:System
Initialized Default: See each program
Program *41-1 – T1 Span (RDTU) Frame and Line Code Assignments
Initialized Default:LED 01 and LED 02 OFF for all T1 span lines




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
T1 SpanExtended Superframe
LED 01 ONSuperframe
LED 01 OFFB8ZS
LED 02 ONAMI Code
LED 02 OFF
1 RDTU
2 RDTU
3 RDTU
4 RDTU
5 RDTU
6 RDTU
7 RDTU
8 RDTU
SELECT = 1
Select the RDTU being 
programmed (1~8)LEDs 01 and 02
Set as described below. 
						

							System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
72Strata DK System Record Sheets 5/99
Program *41-2 – T1 Channel Assignments
Initialized Default:1 = Loop Start




  6SNU
  +ROG  6SNU   +ROG 7XU Q6\VWHP3RZHU2))VHFWKHQ
ProcessorLine Range
RCTUBA/BB 001~048
RCTUC/D 001~144
RCTUE/F 001~200
RDTU:___________ Slot:___________ RDTU:___________ Slot:___________ RDTU:___________ Slot:___________
RDTU Channel No.Line TypeRDTU Channel No.Line TypeRDTU Channel No.Line Type
111
222
333
444
555
666
777
888
999
10 10 10
11 11 11
12 12 12
13 13 13
14 14 14
15 15 15
16 16 16
17 17 17
18 18 18
19 19 19
20 20 20
21 21 21
22 22 22
23 23 23
24 24 24
More channels
or...
Run Program 91-2SELECT = 2
Enter the RDTU being programmed (1~8).
Enter the RDTU channel number (01~24) 
to be assigned a line type.
To add a port range, enter XXX

XXX 
(low port 

 high port).
Enter the line type to be assigned to the RDTU channel:
See Programs 17 and 71 for other Tie/DID assignments;.
See Program *17 and Program *09 for other DID assignments. 1 = Loop Start (initialized) 4 = Tie (Wink)
2 = Ground Start 5 = DID (immediate)
3 = Tie (immediate) 6 = DID (Wink) 
						

							System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
Strata DK System Record Sheets 5/9973
System & Station
Program *41-3 – T1 Span Transmit Level Pad Assignments
Initialized Default:5 (-6dB)
Program *41-4 – T1 Span Receive Level Pad Assignments
Initialized Default:4 (-3dB)
Program *42 for DK424 – T1 Assignment Series (Part 2)
See “Program *42 – Clock Source” on Page 162.




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
SELECT = 3
Enter the RDTU being 
programmed (1~8).Enter one of the following pad codes for the 
transmission of path:
1 = +6 dB pad
2 = +3 dB pad
3 = 0 dB pad
4 = -3 dB pad
5 = -6 dB pad (Initialized: PAD_S = 5)
6 = -9 dB pad
7 = -12 dB pad
8 = -15 dB pad
RDTU No.12345678
PAD Code
SELECT = 4
Enter the RDTU being 
programmed (1~8).Enter one of the following pad codes for the 
transmission of path:
1 = +6 dB pad
2 = +3 dB pad
3 = 0 dB pad
4 = -3 dB pad
5 = -6 dB pad (Initialized: PAD_R = 4)
6 = -9 dB pad
7 = -12 dB pad
8 = -15 dB pad
RDTU No.12345678
PAD Code 
						

							System & Station
Program *50 – Caller ID Circuit Assignments to CO Line PCBs
74Strata DK System Record Sheets 5/99
Program *50 – Caller ID Circuit Assignments to CO 
Line PCBs
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:No RCIU/RCIS circuits assigned




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
CO Line NumberRCIU/RCIS Circuit 
Number AssignedCO Line NumberRCIU/RCIS Circuit 
Number AssignedCO Line NumberRCIU/RCIS Circuit 
Number Assigned
System power must be cycled or Program 91-2 must 
be run after completing *50 data entry to transfer 
data from temporary memory to working memory.
CIUNO = RCIU/RCISU Caller ID circuit number 
(001~200) or use LED Button 01 to erase data. For 
DK14, enter the Caller ID interface box line number 
(001~004).
Any Caller ID circuit can be assigned to any analog 
ground or loop start CO line circuit. Circuit numbers 
do not have to match.
ProcessorCO Line Range
DK14 001~004
DK40i 001~012
RCTUA 001~016
RCTUBA/BB 001~048
RCTUC/D 001~144
RCTUE/F 001~200Run Program 91-2 
						

							System & Station
Program *51 – Station Memory Allocation
Strata DK System Record Sheets 5/9975
System & Station
Program *51 – Station Memory Allocation
for Storing Caller ID/ANI Numbers on Abandoned/
Unanswered Calls
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:No memory for all ports




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Station Logical 
Port NumberMemory Allocation 
(100 max each)Station Logical 
Port NumberMemory Allocation 
(100 max each)Station Logical 
Port NumberMemory Allocation 
(100 max each)
BUF = 000, 010, 020, 030, 040, 060, 070, 080, 
090 or 100.
This is the number of telephone numbers that can 
be stored at the designated port(s). The 
maximum Caller ID/ANI numbers that can be 
stored per telephone is 100.
IDL = Total number of Caller ID/ANI Telephone 
Numbers Available in each system
DK14 200
DK40i 200
RCTUA 200
RCTUBA/BB 400
RCTUC/D 1000
RCTUE/F 2000
ProcessorStation Ports
DK14 000~007
DK40i 000~027
RCTUA 000~031
RCTUBA/BB 000~079
RCTUC/D 000~239
RCTUE/F 000~335
To add a port range, enter 
XXX

XXX (low port 
 high port). 
						

							System & Station
Program *52 – Caller ID/ANI Abandoned Call Number Station Owner Assignments
76Strata DK System Record Sheets 5/99
Program *52 – Caller ID/ANI Abandoned Call Number 
Station Owner Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:No station owners assigned




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
ProcessorCO Line Range[PDN] Port RangeProcessorCO Line Range[PDN] Port Range
DK14 001~004 000~009 RCTUBA/BB 001~048 000~079
DK40i 001~012 000~027 RCTUC/D 001~144 000~239
RCTUA 001~016 000~031 RCTUE/F 001~200 000~335
CLID/ANI 
CO Line 
NumberStation Owner 
Port Number 
AssignedCLID/ANI 
CO Line 
NumberStation Owner 
Port Number 
AssignedCLID/ANI 
CO Line 
NumberStation Owner 
Port Number 
AssignedCLID/ANI 
CO Line 
NumberStation Owner 
Port Number 
Assigned
CLASS OWNER = the station port number that 
should store Abandon Call Numbers for the Caller 
ID or ANI CO Line(s) entered.
Press LED Button 01 to erase data.SELECT = Caller ID or ANI CO Line Number
To add a range of line numbers, enter 
XXX

XXX (low port 
 high port).