Toshiba Strata Dk14, Dk40i, Dk424 System Record Sheets Manual

							System & Station
Program 26 – Built-in AA Camp-on Busy Time
Strata DK System Record Sheets 5/9937
System & Station
Program 26 – Built-in AA Camp-on Busy Time
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:Assigns an AA Camp-on-Busy Time of 016 seconds to all ports




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor Type[PDN] Port RangeProcessor Type[PDN] Port Range
DK14 000~009 RCTUBA/BB 000~079
DK40i 000~027 RCTUC/D 000~239
RCTUA 000~031 RCTUE/F 000~335
PortCamp-on 
TimePortCamp-on 
TimePortCamp-on 
TimePortCamp-on 
Time
SELECT = Port Number
Enter the number of the called Station 
Logical port that needs a Camp-on 
Busy time assigned.
To add a port range, enter XXX

XXX 
(low port 

 high port).CAMP-ON TIME = AA Camp-on-Busy Time
Enter the time in seconds (1~3 digits). The range is 
011~999 seconds (16.65 minutes). 
						

							System & Station
Program 27 – DKT Handset/Headset Receiver Volume Level
38Strata DK System Record Sheets 5/99
Program 27 – DKT Handset/Headset Receiver Volume 
Level
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:VR=2




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeProcessor TypePort Range
DK14 000~007 RCTUBA/BB 000~079
DK40i 000~027 RCTUC/D 000~239
RCTUA 000~031 RCTUE/F 000~335
PortVR LevelPortVR LevelPortVR LevelPortVR Level
Digital Telephone Logical Port Number VR = Enter volume level 1~4
Default volume level is 2.
01234567 8
Total DKT Volume Range (VR)
Highest
Vo l u m e Vo l u m e Lowest
Set VR 1~4 for initial off-hook handset receiver volume level; 
VR resets to programmed level (1~4) after each call (on-
hook/off-hook). Each level is equivalent to a 2dB change. 
						

							System & Station
Program 28 – DSS Console/Attendant Telephone Assignments
Strata DK System Record Sheets 5/9939
System & Station
Program 28 – DSS Console/Attendant Telephone 
Assignments
Processor Type:DK40i, All RCTUs
Program Type:Station
Initialized Default:Assigns Console #1 to Attendant Telephone #1; 
Console #2 to Attendant Telephone #2; etc.




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
ProcessorDSS ConsolesHDSS Consoles
DK14 0 0
DK40i 1~3 1~3
RCTUA 1~3 1~3
RCTUBA/BB 1~4 1~4
RCTUC/D 1~8 1~8
RCTUE/F 1~8 1~8
DDSS PDKU/HDSS PEKU PCBs
(Lowest to Highest)DDSS/HDSS 
Console NumberAttendant DKT/EKT Number (1~8)
Low Slot Number:1
Slot Number:2
Slot Number:3
Slot Number:4
Slot Number:5
Slot Number:6
Slot Number:7
High Slot Number:8
SELECT = 1~8
Enter the DSS console number.
Digital DSS consoles (DDSS) should 
be assigned to digital telephones, and 
electronic consoles (HDSS) should be 
assigned to electronic telephones.DSS ATT = 1~8
Enter the attendant digital or electronic telephone 
number. 
						

							System & Station
Program 29-1~8 – DSS Console and Number Button Assignments
40Strata DK System Record Sheets 5/99
Program 29-1~8 – DSS Console and Number Button 
Assignments 
Processor Type:DK40i, All RCTUs
Program Type:Station
Initialized Default:See “Program 29 - Initialized Default DSS Console Button Assignments” on  Page 41
Code Table and Legend




  6SNU   +ROG  6SNU+ROG 6SNU+ROG 6SNU+ROG
Button TypeCodeProcessorPersonal 
Speed Dial Bin 
NumbersSystem Speed 
Dial Bin 
NumbersCO Line RangeDSS Button 
Range
All Call 489 DK40i

10~
49
60~
99001~012 #000~#027
Night Transfer 1 439 RCTUA

10~
49
60~
99 001~016 #000~#031
Night Transfer 2 440 RCTUBA/BB

10~
49
600~
699001~048 #000~#079
Night Transfer 3 441 RCTUC/D

10~
49
600~
699001~144 #000~#239
Night Transfer 4 442 RCTUE/F

100~
139
200~
999001~200 #000~#335
Console Number _______
Group Number 1Group Number 2Group Number 3
Button/CodeButton/CodeButton/CodeButton/CodeButton/CodeButton/Code
10 20 10 20 10 20
09 19 09 19 09 19
08 18 08 18 08 18
07 17 07 17 07 17
06 16 06 16 06 16
05 15 05 15 05 15
04 14 04 14 04 14
03 13 03 13 03 13
02 12 02 12 02 12
01 11 01 11 01 11
SELECT = DDSS/HDSS console number 1~8
DDSS/HDSS LED Button Group 1~3
Each console has three groups of 20 LED 
buttons.
DKT LEDs 01~20
Press the DKT LED that is in the same position 
as the console button being assigned. The LED 
lights and the LCD displays the console button’s 
number.CODE =
Assign Speed Dial, trunk access, or DSS access to 
this button chosen. See code table below.
The 
1LJKW7UDQVIHU and $OO&DOO3DJH buttons 
may be changed to66, /LQH (
CO) or 6 buttons, 
but they may not be reassigned to other button 
locations.
Initialized key assignments are shown following the 
Program 29 System Record Sheets. 
						

							System & Station
Program 29-1~8 – DSS Console and Number Button Assignments
Strata DK System Record Sheets 5/9941
System & Station
Program 29 - Initialized Default DSS Console Button Assignments
Group 1 Group 2
DSS
Button No.DK40iRCTUARCTUB
RCTUC/D
RCTUE/FDSS
Button NoDK40iRCTUARCTUB
RCTUC/D
RCTUE/F
01 #000 #000 #000 01 #020 #020 #020
02 #001 #001 #001 02 #021 #021 #021
03 #002 #002 #002 03 #022 #022 #022
04 #003 #003 #003 04 #023 #023 #023
05 #004 #004 #004 05 #024 #024 #024
06 #005 #005 #005 06 #025 #025 #025
07 #006 #006 #006 07 #026 #026 #026
08 #007 #007 #007 08 #027 #027 #027
09 #008 #008 #008 09

10 #028 #028
10 #009 #009 #009 10

11 #029 #029
11 #010 #010 #010 11

12 #030 #030
12 #011 #011 #011 12

13 #031 #031
13 #012 #012 #012 13

14
10 #032
14 #013 #013 #013 14

15
11 #033
15 #014 #014 #014 15

16
12 #034
16 #015 #015 #015 16

17
13 #035
17 #016 #016 #016 17

18
14 #036
18 #017 #017 #017 18

19
15 #037
19 #018 #018 #018 19

20
16 #038
20 #019 #019 #019 20

21
17 #039
Group 3
DSS
Button NoDK40RCTUARCTUB
RCTUC/D
RCTUE/F
01
22
18 #040
02

23
19 #041
03

24
20 #042
04

25
21 #043
05

26
22 #044
06

27
23 #045
07

28
24 #046
08

29
25 #047
09

30
26 #048
10

31
27 #049
11

32
28 #050
12

33
29 #051
13

34
30 #052
14

35
31 #053
15

36
32 #054
16

37
33 #055
17

38
34 #056
18

39
35 #057
19 AC (489) AC (489) AC (489)
20 NT 1 (439) NT 1 (439) NT 1 (439) 
						

							System & Station
Program *29 – Add-on Modules Button Assignments
42Strata DK System Record Sheets 5/99
Program *29 – Add-on Modules Button Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:See “Program 29 - Add-on Modules Button Assignments” on Page 3-74




  6SNU
  +ROG  6SNU+ROG 6SNU+ROG 6SNU+ROG
ProcessorPersonal Speed Dial Bin 
NumbersSystem Speed Dial 
Bin NumbersCO Line RangeDSS Button Range
DK14

10~
49
60~
99 001~004 #000~#009
DK40i

10~
49
60~
99 001~008 #000~#027
RCTUA

10~
49
60~
99 001~016 #000~#031
RCTUBA/BB

10~
49
600~
699 001~048 #000~#079
RCTUC/D

10~
49
600~
699 001~144 #000~#239
RCTUE/F

100~
139
200~
999 001~200 #000~#335
Port _____ Port _____
Add-on Module 1 Add-on Module 2 Add-on Module 1Add-on Module 2 
ButtonCodeButtonCodeButtonCodeButtonCodeButtonCodeButtonCodeButtonCodeButtonCode
10 20 10 20 10 20 10 20
09 19 09 19 09 19 09 19
08 18 08 18 08 18 08 18
07 17 07 17 07 17 07 17
06 16 06 16 06 16 06 16
05 15 05 15 05 15 05 15
04 14 04 14 04 14 04 14
03 13 03 13 03 13 03 13
02 12 02 12 02 12 02 12
01 11 01 11 01 11 01 11
ProcessorADMsNumber of 
System Speed 
Dial NumbersNumber of 
Personal Speed 
Dial Numbers
DK14 8 40 40
DK40i 12 40 40
RCTUA 12 40 40
RCTUBA/BB 40 100 40
RCTUC/D 120 100 40
RCTUE/F 200 800 40
Enter the station logical port of the telephone which 
will have buttons assigned to its attached Add-on.
Enter the Add-on Module which will have buttons 
assigned to it (0, 1, or 2). Enter 0 when removing 
ADMs.CODE=
See the Code Table below.
LED 01~20
Press the LED that is in the same position as 
the Add-on Module button being assigned. 
						

							System & Station
Program *29 – Add-on Modules Button Assignments
Strata DK System Record Sheets 5/9943
System & Station
Button Assignments
Add-on 
Module 1
Button 
No.
DK14DK40iRCTUARCTUB
RCTUC/D
RCTUE/FAdd-on 
Module 2
Button No.DK14DK40iRCTUARCTUB
RCTUC/D
RCTUE/F
01 #000 #000 #000 #000 01
20 #020 #020 #020
02 #001 #001 #001 #001 02

21 #021 #021 #021
03 #002 #002 #002 #002 03

22 #022 #022 #022
04 #003 #003 #003 #003 04

23 #023 #023 #023
05 #004 #004 #004 #004 05

24 #024 #024 #024
06 #005 #005 #005 #005 06

25 #025 #025 #025
07 #006 #006 #006 #006 07

26 #026 #026 #026
08 #007 #007 #007 #007 08

27 #027 #027 #027
09 #008 #008 #008 #008 09

28
10 #028 #028
10 #009 #009 #009 #009 10

29
11 #029 #029
11

10 #010 #010 #010 11
30
12 #030 #030
12

11 #011 #011 #011 12
31
13 #031 #031
13

12 #012 #012 #012 13
32
14
10 #032
14

13 #013 #013 #013 14
33
15
11 #033
15

14 #014 #014 #014 15
34
16
12 #034
16

15 #015 #015 #015 16
35
17
13 #035
17

16 #016 #016 #016 17
36
18
14 #036
18

17 #017 #017 #017 18
38
19
15 #037
19

18 #018 #018 #018 19
39
20
16 #038
20

19 #019 #019 #019 20
40
21
17 #039 
						

							System & Station
Program 30 – Station Class of Service
44Strata DK System Record Sheets 5/99
Program 30 – Station Class of Service
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:LEDs 01, 05 and 07 for all ports




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeDISA PortProcessor TypePort RangeDISA Port
DK14 000~009 010 RCTUBA/BB 000~079 089
DK40i 000~027 035 RCTUC/D 000~239 249
RCTUA 000~031 039 RCTUE/F 000~335 344
FeatureLEDPort
SLT/ISDN Terminal “#” Dial20
Privacy Override19
Executive Override18
DND Override17
Change TR Traveling Class Code16
Change Verified Account Code15
Verified Account Codes14
13
SLT-Hook Flash Anti-Bounce Guard12
Dial Pulse - DTMF OFF11
Change DISA Security Code10
Change TR Override Code09
Forced Account Code08
OCA Automatic (originating OCA)07
ABR Access06
Speed Dial Allowed05
#5#30 Pickup AC Page Only 
(Release 3.2 and higher)04
Microphone Button on at Start of Call03
MIC Button Locked02
Speakerphone01
SELECT = Station Logical Port Number(s)
Enter the port numbers to which class of service 
must be assigned. To add a port range, enter 
XXX

XXX (low port 
 high port).Light LEDs for the port specified in the last step. All 
LEDs marked with an “X” in the table below should 
be lit. 
						

							System & Station
Program *30 – Telephone Group Page Assignments
Strata DK System Record Sheets 5/9945
System & Station
Program *30 – Telephone Group Page Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:All LEDs OFF
Shaded groups apply to RCTUC/D and RCTUE/F only.




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeNumber of Page GroupsProcessor TypePort RangeNumber of Page Groups
DK14 000~007 4 RCTUBA/BB 000~079 4
DK40i 000~027 4 RCTUC/D 000~239 8
RCTUA 000~031 4 RCTUE/F 000~335 8
FeatureLEDPort
Page Group H
08
Page Group G
07
Page Group F
06
Page Group E
05
Page Group D04
Page Group C03
Page Group B02
Page Group A01
Enter the station logical port which will be assigned 
to page a group or groups. To add a port range, 
enter XXX

XXX (low port 
 high port).Press LED Buttons 01~08 to light LEDs for the port 
specified in the last step. In the table below, “X” all 
LED Buttons which should be lit. 
						

							System & Station
Program 31 – Station Class of Service
46Strata DK System Record Sheets 5/99
Program 31 – Station Class of Service
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:LED 10 ON for Ports 000~119; LED 11~13 ON for all ports.
 




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeProcessor TypePort Range
DK14 000~009 RCTUBA/BB 000~079
DK40i 000~027 RCTUC/D 000~239
RCTUA 000~031 RCTUE/F 000~335
FeatureLEDPort
Toshiba Stratagy/VP (B + Station No.)20
Toshiba Stratagy/VP (B No Station)19
Executive & Privacy Override Blocking18
End/End Signal Rcv (VM)17
Receive VM ID Code16
Toshiba Stratagy/VP Integration (A/D)15
Handset OCA14
Handset OCA Warning Tone13
Pooled Line Key - No Flash if No Ring12
Busy Override Tone - Continuous11
All Call Page Allowed - EKTs/DKTs10
VM (No Conference)09
VM Group 4 (does not apply to DK14)08
VM Group 3 (does not apply to DK14)07
VM Group 206
VM Group 105
VM to VM Call Blocking Called/Calling04
OCA Enabled (To Receive)03
Handsfree No Warning Tone02
Handsfree Disabled01
SELECT = Station Logical Port Number(s)
Enter the port numbers to which class of service 
must be assigned. Light LED Buttons for the port specified in the last 
step. All LED Buttons marked with an “X” in the 
table below should be lit.