Toshiba Strata Dk14, Dk40i, Dk424 System Record Sheets Manual

							System & Station
Program 05 – Flexible Access Code Numbering
Strata DK System Record Sheets 5/9917
System & Station
Program 05 – Flexible Access Code Numbering
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:See record sheet




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Default 
Access 
CodeFeatures Affected
(N/A = Not Affected/ Cannot Change)New 
Access 
Codes
0Unused
1
Voice First/Tone First (Dial 1-N/A)
Door Phones: (#151~#159; #161~#163)
IMDU or RMDS Access: DK424 and DK40i (#19)
Default [PDNs] and Park Orbits (see Program 04)Station LCD Messages (10~19-N/A)
Station Speed Dial (100~139-N/A) RCTUE/F
Station Speed Dial Set (10~49-N/A) RCTUA, BA/BB, 
C/D
2
Default [PDNs] and Park Orbits (see Program 04)
Busy Override (Dial 2-N/A)
Do Not Disturb Override (Dial 2-N/A)ACD Ports (*04, *09, 71)
Off-hook Call Announce (2-N/A)
RCTUE/F System Speed Dial (200~999)
3
Default [PDNs] and Park Orbits (see Program 04)
Executive Override (Dial 3-N/A)
All Call Voice Page (#30)
All Call Voice Page with External Spkrs (#39)
RCTUE/F Ext Page Zones #351~#358RCTUA~C/D External Page Zones 1~4 (#35~#38)
Group Page (Internal) (#311~#318)
Park + Page (Cnf+#331)
Park Pick Up [DN]+#331 (see Program 
*05)
Park + Hold (Cnf+#332)
4
Default [PDNs] and Park Orbits (see Program 04)
Default [PhDNs] (see Program 
*04)
Automatic Callback (Dial 4-N/A)
CO Line Queuing (Dial 4-N/A)
Station Number Display (#401)
Port Number Display (#402)
Hold (#41)
Hold Pickup (#42)
Automatic Busy Redial (Conf + #44)
Automatic Busy Redial Cancel (Int + #44)
Message Waiting Answer (#408) from INT, [PDN], or 
[PhDN]
Display [PDN], [SDN], or [PhDN] on LCD (#407)
Emergency Call to Attendant Console (#400)
Standard telephone Redial (44) or dial # for feature 
access code
Flash (Cnf + #45)
Account Code Input (Cnf + #46)T.R. Override/T. Class Code Input (Cnf + #47)
BGM Over Stations ON (#481)
BGM Over Stations OFF (#480)
BGM Over External Speakers ON (#491)(Station Port 
000 only)
BGM Over External Speakers OFF (#490)(Station 
Port 000 only)
Cancel Message Waiting at Station (#409) from [PDN] 
or [PhDN]
Retrieve Message Waiting (#408)
Access Code/Speed Dial Prefix (44 or #)
To store a CO line or feature access code in Speed 
Dial memory from rotary phones or phones without 
the Speed Dial and Redial buttons, enter 44 + 7XXX 
instead of # + 7XXX.
Start Trace #489 (Station Port 000 only)
Stop Trace #488 (Station Port 000 only)
Cancel Auto Call Back (#43)
SELECT = Access Code (1~9)
See the table below for standard 
access codes.SPECIAL DIAL = New Access Codes
The first digit of access codes can be replaced by 2 digits.
Press LED Button 01 to enter blanks. 
						

							System & Station
Program 05 – Flexible Access Code Numbering
18Strata DK System Record Sheets 5/99
5
Call Pickup Station (#5+Station No.), Ringing CO or 
DID line (#59)
Directed Pickup of CO Line on Hold (#5+#7 XXX, 
XXX = 001~200),
Pick-up External Page (#5 +#30 or for Zone Page 
#5+#35~#38)
#5#79 Pick up Tandem Connection (Release 3.2 and 
above)Selected Group Pickup (#5+#320~#339)
Own Group(s) Pickup (#5+#34) 
Pickup Ringing Line (#59)
[DN] Pickup #5#2+XXX (XXX=[PDN] or [PhDN], DK 
Release 3.1 and above)
Verified Account Codes (DK14, DK40i, RCTUA~C/D: 
Speed Dial + 50; RCTUE/F Speed Dial + 050)
6
Call Forward (#601, #602, #603, #604)
Timed Reminder (#605~#609)
M/W for Voice Mail ON (#63+Station No.)
M/W for Voice Mail OFF (#64+Station No.)
Voice Mail ID Code Set (Call Fwd, #656)
Voice Mail ID Code Set (Ans. MW, #657)
LCD Message Set (#68)
DKT Mute Ring Adjust (#6101)
DKT Ring Level Adjust (#6102)
Port Swap/Station Relocation OFF (#6281)
Station Relocation ON (#6282)
Logical Por t Swap ON (#6283)
Call Forward Ext Set or Remote Change Code (#670)
Date Set (#651)
Time Set (#652)
Weekday Set (#653)T.R. Override Code Change (#654, #655)
System Speed Dial
(N/A 600~699 RCTUB, RCTUBA/BB, & 
RCTUC/D)
System Speed Dial Set (N/A 60~99 - DK14, DK40i 
and RCTUA)
LCD User Name (#621-Set, #620-Reset, TR dial plan 
Set #650 +6267 +7/8/9 Change
DISA Security Code Change (#658) 
Verified Account Code Change (#659)
Set LCD Messages (#68)
System LCD Messages (N/A 60-99)
Traveling Class Code 1~8 Change (#691~#698)
Logical Por t Swap (#627 + Destination Intercom No.)
Physical Port Calling (#629 + Physical Port No.)
Message Waiting Set/Cancel (N/A) (7) (77)
Night Lock Password Change (#622)
7
CO Line Outgoing Calls (#7001~#7200)
To store a CO line or feature access code in Speed Dial memory from rotary telephones or telephones without 
the Speed Dial and Redial buttons, enter 44 + 7XXX instead of # + 7XXX.
8CO Group Outgoing Calls (801~816) Default Distributed Hunt [DNs] (850~ 865)
See Program *04
9Least Cost Routing or CO Group (9), Distributed Hunt Group Prog *04 Port Ref. (900~915)
Default 
Access 
CodeFeatures Affected
(N/A = Not Affected/ Cannot Change)New 
Access 
Codes 
						

							System & Station
Program *05 – Call Park Pickup Abbreviated Dialing
Strata DK System Record Sheets 5/9919
System & Station
Program *05 – Call Park Pickup Abbreviated Dialing
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:Blank
Program 09 – Built-in Auto Attendant Prompt / Station 
Assignments
Processor Type: DK14, DK40i, All RCTUs
Program Type:System and ACD
Initialized Default:Blank




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Dialed Digit (Menu Prompts)Station Number [PDN]Department, Division, Etc.
0
1
2
3
4
5
6
7
8
9
DATA = 1 or 2 digit abbreviated 
dialing for Call Park Pickup.SELECT = 1
SELECT = Call Park type:
1 = Change #331 Call Park Pickup Code
2 = Change #332 Call Park Pickup Code
It is only necessary to change one code, but 
each code can be changed to the same or 
SELECT = Prompt
Press prompt number offered 
to caller. First or second digit.AUTO ATT DIAL = (1~4 digits)
Enter the station numbers, [PDNs], [PhDNs], DH 
[DNs], or #4 plus the ACD Group No. which will 
receive Auto Attendant calls. Could be 

 if 
establishing the first digit.
Press LED Button 01 to delete data. 
						

							System & Station
Program *09 – [PDN], [PhDN], DH, ACD or Modem DID Ext. Assignments
20Strata DK System Record Sheets 5/99
Program *09 – [PDN], [PhDN], DH, ACD or Modem DID 
Ext. Assignments
Processor Type:See legend below
Program Type:Station
Initialized Default:See legend below




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor[PDN] 
Port 
Range[PDN] Ext. 
#[PhDN] 
Port 
Range[PhDN] 
Ext. #DH Group 
PortsDH Ext. # 
DefaultACD 
Port #ACD Ext. #RMDS/IMDU 
Modem PortModem 
[PhDN] Ext. #
DK14 000~009 10~19 500~509 50~59 900~915 Blank N/A N/A N/A N/A
DK40i 000~027 10~37 500~527 50~77 900~915 Blank N/A N/A 031 41
RCTUA 000~031 200~231 500~531 500~531 900~915 Blank N/A N/A 035 235
RCTUBA/BB 000~079 200~279 500~579 500~579 900~915 Blank 090~097 290~297 085 285
RCTUC/D 000~239 200~439 500~739 500~739 900~915 Blank 250~265 450~465 245 445
RCTUE/F 000~335 100~435 500~835 450~785 900~915 Blank 345~360 850~865 340 840
[PDN], 
[PhDN], DH, 
ACD or 
Modem Port[PDN], [PhDN], DH, ACD 
or Modem Port
DID Ext. # (1~4 Digits)[PDN], 
[PhDN], DH, 
ACD or 
Modem Port[PDN], [PhDN], DH, ACD 
or Modem Port
DID Ext. # (1~4 Digits) [PDN], 
[PhDN], DH, 
ACD or 
Modem Port[PDN], [PhDN], DH, ACD 
or Modem Port
DID Ext. # (1~4 Digits) 
SELECT =  Port No. (see legend)
To add a port range, enter XXX

XXX 
(low port 

 high port). (Do not press # after entering a port range.) Then enter 
the lowest DID Ext. number as the first 
Ext. number in the range.DIAL = DID Extension Number (1~4 digits)
Press LED Button 01 to erase extension 
numbers. 
						

							System & Station
Program 10-1 – System Assignments, Part 1 of 3
Strata DK System Record Sheets 5/9921
System & Station
Program 10-1 – System Assignments, Part 1 of 3
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:LEDs 07, 08, 09, 16, 18, 19 and 20 are ON




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Button/
LEDXLED ONLED OFF
20
Two-CO Line Conference/Allowed Not Allowed
Two-CO line Conference must be allowed for Tandem Line, DISA, 
CF-EXT, and DNIS external routing operation. Also See Program 
15, Code 5.
19Conference/Allowed Not Allowed
18Ring Detect Time-Normal Ring Detect Time-Short Rings
17Station to Station Call Volume PAD (-
8db)No Station to Station Call PAD
16BRI Standard Initialization (2 TEIs) None (TEI = 0)
15~13Not Used Not Used
12ABR Cycles/10 times 15 times
11ABR Redial time/30 sec. 1 min.
10System Speed Dial Override, Toll 
RestrictionRestricted
09Exclusive Hold/Allowed Not Allowed
08Alternate Point Answer Transfer Privacy
07Ring Transfer of CO Line Allowed Not Allowed
If Ring Transfer is allowed, set Ring Transfer Recall time in Program 
37; if ring transfer is not allowed (LED 07 OFF), the station recalls 
immediately if transfer is attempted.
06CO Line Repeat Ringing Standard Ring
Standard ring pattern is 1 sec. on, 3 sec. off.
05Incoming Call Abandon 8 sec. 6 sec.
04CO Line DTMF Signal Time 160 msec. 80 msec.
LED 04 DTMF Signal Time applies to manual and speed dial tones 
sent out of the system via CO lines. This applies when dialing from 
any Toshiba telephone, including the 2000-series Digital Telephone. 
LED 04 does not apply to Call Forward or Voice Mail ID DTMF tones 
sent to voice mail ports. (See Program 10-2, LED 06, for tones sent 
to Voice Mail ports.)
03Dial Pulse Make Ratio 33% 40%
020.45 or 1.5 sec. per Program 42-0 CO Line Re-seize guard time 0.45
CO line guard time is the time interval the system requires to release 
a CO line and reseize it. If LED 02 is off, all lines are set with 0.45 
second guard time; if LED is on, guard time is 0.45 or 1.5 seconds 
per Program 42-0.
01Tone First (from SLTs, DKTs and EKTs) Voice First (from SLTs, DKTs and EKTs)
This applies to [PDNs] not [PhDNs]; [PhDNs] are always tone first.
SELECT = 1 Light the LED Buttons that are marked with an X in 
the table below. 
						

							System & Station
Program 10-2 – System Assignments, Part 2 of 3
22Strata DK System Record Sheets 5/99
Program 10-2 – System Assignments, Part 2 of 3
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:LEDs 02, 14, 15, and 16 are ON




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Button/
LEDXLED ONLED OFF
20Padded DTMF Tone Return 
When DialingDTMF/No DTMF Per Prog 10-2, LED 11
19External Conference Amp 
Connected to PEKUNo External Amplifier Connected
18External Conference Amp 
Connected to PEKUNo External Amplifier Connected
17“TRNS” Soft Key—
Immediate“TRNS” Soft Key—Normal
16Executive Override Warning 
To n e / O NExecutive Override Warning Tone/OFF
15External Page included with 
All Call PageNot Included - see Button/LED 20 note.
14Privacy Override/Attendant/
Supervised Loop Warning 
To n e / O NPrivacy/Attendant Supervised Loop Override Warning Tone/OFF
13Send Auto Callback Camp-
on ToneNo Callback Tone. Called party receives notification tone when calling party activates Auto Call 
Back.
12CO Line 3 min Beep Tone No Beep Tone
11No DTMF Tone Return When 
DialingDTMF tone return when dialing
10BGM connected to PESU, 
Circuit 8EKT connected to PESU, CKT 8
09BGM connected to PEKU, 
Circuit 3EKT connected to PEKU, CKT 3
08Elapsed Time Display 1 min. 
After Access or Answer a CO 
lineElapsed Time Display 15 sec. After Access or Answer a CO Line
07Standard Tel. CO Ring per 
Prog. 10-1, LED 06Standard Tel. CO Ring Distinctive
06VM ID Code DTMF Signal 
Time 80 ms160 ms
05Send Music-on-hold. Send Ringback Tone to the transferred party.
04MW cancel from VM: RS-232 
or dial 
#64 + [DN]MW cancel from VM: Automatic When Answer
033 Ringing Modes 2 Ringing Modes
02Hunt/C.F. override from DSS 
consoles phoneHunt/C.F. override from DSS console
01Tone First (from DSS 
Console)Voice First (from DSS Console)
This applies to [PDNs] not [PhDNs]; [PhDNs] are always tone first.
SELECT = 2 Light the LED Buttons that are marked with an X in 
the table below. 
						

							System & Station
Program 10-3 – System Assignments, Part 3 of 3
Strata DK System Record Sheets 5/9923
System & Station
Program 10-3 – System Assignments, Part 3 of 3
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:LEDs 11, 13 and 20 ON, all other LEDs OFF




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Button/
LEDXLED ONLED OFF
20SMDI Message Desk Number (001) is sent in SMDI 
packet.CO line number is sent in SMDI packet.
19Speed Dial Entry Timeout- 3 minutes Speed Dial Entry Timeout - 1 minute
18Auto Attendant: Normal Ringing Pattern After Camp-
onAuto Attendant: Back to Announcement After Camp-on
17Auto Attendant: Ring Before Disconnect time Auto Attendant: Ring Before Disconnect time
16Auto Attendant: Ring Before Disconnect time Auto Attendant: Ring Before Disconnect time
15Auto Attendant: Sends MOH to Caller Auto Attendant: Sends RBT to Caller
14SMDI-Bellcore Standard VM Interface, per LED 09 
BelowNot used
13SMDI-Station Number Digit Length (HEX-8) SMDI-Station Number Digit Length (HEX-0)
12SMDI-Station Number Digit Length (HEX-4) SMDI-Station Number Digit Length (HEX-0)
11SMDI-Station Number Digit Length (HEX-2) SMDI-Station Number Digit Length (HEX-0)
10SMDI-Station Number Digit Length (HEX-1) SMDI-Station Number Digit Length (HEX-0)
09Bellcore Standard 1985 Version (1-space) Bellcore Standard 1985 Version (2-space)
08Caller ID/ANI numbers are sent out the SMDI port Caller ID/ANI numbers are not sent out the SMDI port.
07
06
05
04PEKU Ports 33, 34-Amp, connected (RCTUBA/BB 
or higher)PEKU Ports 33, 34-stations connected
03PEKU Ports 25, 26-Amp, connected PEKU Ports 25, 26-stations connected
02PEKU Ports 17, 18-Amp, connected PEKU Ports 17, 18-stations connected
01PEKU Ports 09, 10-Amp, connected PEKU Ports 09, 10-stations connected
SELECT = 3 Light the LED Buttons that are marked with an X in 
the table below. 
						

							System & Station
Program *10 – Enhanced 911 Operation
24Strata DK System Record Sheets 5/99
Program *10 – Enhanced 911 Operation
Processor Type:DK14, DK40i, all RCTUs
Program Type:System
Initialized Default:See each program
Programs *10-11 and *10-12 – E911 Standard Telephone Ports Assignment
Initialized Default:Blank
Program *10-91 – E911 Interdigital Time
Initialized Default:15 seconds
Program *10-92 – E911 Pause Before Send Timer
Initialized Default:0 - No pause




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
First E911 Port = 11
Second E911 Port = 12E911 RSTU/KSTU2 Port Number
E911 RSTU/KSTU2/QSTU2 Port Number
First Standard Port
Second Standard Port
Interdigit Timer = 91 01~15 seconds
Interdigit Timerseconds
Pause Timer = 92 0 = No pause
1 = 1.5 second pause
2 = 3 second pause
Pause Timerseconds 
						

							System & Station
Program 12 – System Assignments, Basic Timing
Strata DK System Record Sheets 5/9925
System & Station
Program 12 – System Assignments, Basic Timing
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:Program Timing
Code 1 15 secs.
Code 3 1
Code 4 2
Code 5 0
Code 8 1
Code 9 4




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Program 
CodeFunctionCodeTimeRequired 
Code
1Standard Telephone Ring Down Timer (Release 4.0) XX  XX = 2 digits. 00~60 secs.
3Pause Timing
(Speed Dial)1 1.5 sec
23.0 sec.
4
Flash Timing 1 0.5 sec.
2 2.0 sec. (Not used in U.S.)
40.2 sec.
5
Pause After Flash 
(Voice Path Delay)0 no pause
11.5 sec.
23.0 sec.
8
DNIS Ext. Network, External Call Forward, and DISA 
Disconnect Timer for Loop Start Lines0 no disconnect timer
1 4 min. disconnect
2 10 min. disconnect
3 20 min. disconnect
9QRCU3/K4RCU3/RRCS DTMF Inter-digital Release Time 
(Standard Phone)1~9 1~9 secs.
SELECT = 1, 3~5, 8, 9
Enter program code from 
the table below.DATA = Enter ring down time (00~60)
SELECT CODE = Enter the 1 digit code which 
corresponds to the time listed in the table below.
For Program Codes 8 and 9, the LCD responds with 
LINE TIME =, instead of SELECT CODE =. 
						

							System & Station
Program 13 – Defining the Message Center
26Strata DK System Record Sheets 5/99
Program 13 – Defining the Message Center
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:No port assigned




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
SELECT = 1 PORT = Station Logical Port Number
Enter the station logical port number of the station 
to be defined as the Message Center.
For RS-232 SMDI and In Band (DTMF) voice mail 
integration, enter the lowest QSTU2/KSTU2/
RSTU2 standard telephone port connected to the 
VM device (see notes below.)
Port Number