Toshiba Strata Dk14, Dk40i, Dk424 System Record Sheets Manual

							System & Station
Program 15 – Ground/Loop/Tie/DID Line Options
Strata DK System Record Sheets 5/9927
System & Station
Program 15 – Ground/Loop/Tie/DID Line Options
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:All LEDs are OFF




  6SNU   +ROG  6SNU+ROG 6SNU+ROG 6SNU+ROG
Processor TypeCO Line RangeProcessor TypeCO Line Range
DK14 001~004 RCTUBA/BB 001~048
DK40i 001~012 RCTUC/D 001~144
RCTUA 001~016 RCTUE/F 001~200
Program Code
ProgramLED ONLED OFF
Line
LED
0102030405060708091011121314151617181920
0CPC on AR VM 
Calls and Voice 
CallsDetect Ignore
1CO/DID/Tie Line 
SignalDP DTMF
2CO/DID/Tie Dial 
Pulse Rate
(Pulse per sec.)20 PPS 10 PPS
3AR Hold Detect  Ignore
4AR Timing Crossbar 
95 msec.ESS 
(electronic) 
450 msec.
5Tandem CO Line 
Connection with 
Station DropoutEnabled Not 
Enabled
7Forced Account 
CodeEnabled Not 
Enabled
8Operation After CO 
Line FlashNo DTMF 
receiver 
After FlashDTMF 
receiver 
After Flash
SELECT = Program Code
Press 
6FUROO to advance or 3DJH to go back.
To advance the CO line range, press 
6FUROO 
located beneath the LCD. Press 
3DJH for a 
lower range.LED Buttons = CO line
Specify CO line by setting LEDs as defined by the 
table below. When you are finished, all LEDs with 
an “X” should be lit. 
						

							System & Station
Program *15 – CO Line Tenant Assignments
28Strata DK System Record Sheets 5/99
Program *15 – CO Line Tenant Assignments
Processor Type:DK14, DK40i, All RCTUs 
Program Type:System
Initialized Default:All CO lines assigned to Tenant 1




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor TypeCO Line RangeTenants SupportedProcessor TypeCO Line RangeTenants Supported
DK14 001~004 2 RCTUBA/BB 001~048 4
DK40i 001~012 2 RCTUC/D 001~144 4
RCTUA 001~016 2 RCTUE/F 001~200 4
CO 
LineTenant GroupCO 
LineTenant GroupCO 
LineTenant Group
123412341234
SELECT =  CO Line Number
To add a line range, enter XXX

XXX (low port 
 high port).TENANT = Assign the CO line to a tenant 
(see legend below) 
						

							System & Station
Program 16 – Assign CO Line Groups (or Dial 9)
Strata DK System Record Sheets 5/9929
System & Station
Program 16 – Assign CO Line Groups (or Dial 9)
Processor Type:DK14, DK40i, All RCTUs 
Program Type:System
Initialized Default:All CO lines assigned to the Dial 9 group




  6SNU   +ROG  6SNU+ROG 6SNU+ROG 6SNU+ROG
Processor 
Ty p eCO Line RangeCO Line GroupsProcessor 
Ty p eCO Line RangeCO Line Groups
DK14 001~004 01~04 RCTUBA/BB 001~048 01~08
DK40i 001~012 01~08 RCTUC/D 001~144 01~16
RCTUA 001~016 01~08 RCTUE/F 001~200 01~16
LEDLine 
NumberCO Line Groups
Dial 
9(00)
20
19
18
17
16
15
14
13
12
11
10
09
08
07
06
05
04
03
02
01
SELECT = CO Line Group (see legend)
Only enter the last two digits of the CO line 
Group, or enter 
 for Dial 9 group.
Press 
6FUROO to advance or 3DJH to go back.
To advance the CO line range, press 
6FUROO 
located beneath the LCD. Press 3DJH for a 
lower range.LED Buttons = CO line
Specify CO line by setting LEDs as defined by the 
table below. When you are finished, all LEDs with 
an “X” should be lit. 
						

							System & Station
Program 17 – DID/Tie Line Options
30Strata DK System Record Sheets 5/99
Program 17 – DID/Tie Line Options
Processor Type:DK40i, All RCTUs
Program Type:System
Initialized Default:LED 01/02 OFF, LED 03/04 ON




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Line Numbers:
LED/ButtonXLED ONLED OFF
09, 10, and 
14~20Not used at this time.
08DID/Tie line DTMF digits with 

 tones DID/Tie line DTMF digits without 
 tones
07DID/Tie line receives ANI and routes per Programs 71 and 72 DID/Tie line does not receives ANI (DID Program *09 and 
Tie Program 04)
06Telephone LCD priority is ANI Telephone LCD priority is DNIS
05DID/Tie line routes per DNIS assignments:
(Programs 71 and 72)DID/Tie line routes per Non-DNIS assignments:
(DID Program *09 and Tie Program 04)
04DID/Tie no second dial tone DID/Tie second dial tone
03DID line Auto Camp-on busy DID line no Camp-on busy
02Wink Start for Tie or DID Immediate Start for Tie or DID
01Page and Voice Announce on incoming Tie line Page access for 
Tie/DID DNIS linesNo Page and Voice Announce on incoming Tie line No 
Page access for Tie/DID DNIS lines
Enter Line No. that will be DID or Tie line.
To add a port range, enter XXX

XXX (low port 
 high port).Light LED Buttons 01~08 as noted in table below 
						

							System & Station
Program *17 – DID Intercept Port Number (Vacant or Wrong Number)
Strata DK System Record Sheets 5/9931
System & Station
Program *17 – DID Intercept Port Number (Vacant or 
Wrong Number)
Processor Type:DK40i, All RCTUs 
Program Type:System
Initialized Default:No data




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor TypeDID Line RangeIntercept Port RangeProcessor TypeDID Line RangeIntercept Port Range
DK14 N/A N/A RCTUBA/BB 001~048 000~079
DK40i 001~012 000~027 RCTUC/D 001~144 000~239
RCTUA, RCTUB 001~016 000~031 RCTUE/F 001~200 000~335
DID LIne NumberIntercept Port 
NumberDID LIne NumberIntercept Port 
NumberDID LIne NumberIntercept Port 
Number
SELECT =  DID Line Number
Intercept does not apply to Tie line calls.
To add a port range, enter XXX

XXX (low port 
 high port).HUNT TO = Enter Intercept Station 
Logical Port No.
LED Button 01 enters blanks. 
						

							System & Station
Program 19 – Alternate Background Music Source Slot Assignment
32Strata DK System Record Sheets 5/99
Program 19 – Alternate Background Music Source Slot 
Assignment
Processor Type:DK40i, All RCTUs (not used for DK14. See Program 10-2, LED 10)
Program Type:System
Initialized Default:Slot 11
Program 20 – Computer and Data Interface Unit 
Configuration
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:LED 17 ON, all others OFF




  6SNU   +ROG  6SNU  +ROG Turn System Power OFF (5 sec) then ON




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeProcessor TypePort Range
DK14 000~009 RCTUBA/BB 000~079
DK40i 000~027 RCTUC/D 000~239
RCTUA 000~031 RCTUE/F 000~335
DK40i Base, PDKU, RDSU, KCDU Digital Port Number
LEDXLED ONLED OFF
20Data Security Group 4 Not Included
19Data Security Group 2 Not Included
18Data Security Group 3 Not Included
17Data Security Group 1 Not Included
12~16Not Used
11RPCI-DI DNIS Sent RPCI-DI DNIS Not Sent
10RPCI-DI Caller ID/ANI Sent RPCI-DI Caller ID/ANI Not Sent
07~09Not Used
06DTR Pulse
 with Data Release  No DTR Pulse
05Auto Pause Behind PBX No Auto Pause
04PDIU-DS Connected PDIU-DI/RPCI-DI Connected
03PDIU-DS to Modem Connection PDIU-DS to other type DCE or DTE
02AT Commands and Result Codes AT Commands Only
01PDIU-DS or RPCI Connected No PDIU-DS or RPCI Connected
more codes
...or
Run Program 91-2
Enter the Slot Number (11~78)
SELECT = 1
SELECT = PDKU/PDSU Station Logical Port 
Number that is connected to PDIIU-DS or to 
DKT with PDIU-DI or RPCI-DILED Buttons 01~06 define data port type;
LED Buttons 17~20 assign data port to 
security group. 
						

							System & Station
Program 21 – Modem Pool Port Assignments
Strata DK System Record Sheets 5/9933
System & Station
Program 21 – Modem Pool Port Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:Blank




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeProcessor TypePort Range
DK14 008~009 RCTUBA/BB 008~079
DK40i 008~027 RCTUC/D 008~239
RCTUA 008~031 RCTUE/F 008~335
Logical Port No.Modem Port No.
Assignment 1
Assignment 2
Assignment 3
Assignment 4
Assignment 5
Assignment 6
Assignment 7
Assignment 8
Assignment 9
Assignment 10
Digital Station Logical Port 
Number (see notes below)Standard Telephone Modem Port 
Number (see notes below) 
						

							System & Station
Program 22 – RPCI and DIU Station Hunting for Data Calls
34Strata DK System Record Sheets 5/99
Program 22 – RPCI and DIU Station Hunting for Data 
Calls
Processor Type:DK14, DK40i, All RCTU’s
Program Type:Station
Initialized Default:Does not assign “hunt-to” ports to any port




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor TypePort RangeProcessor TypePort Range
DK14 000~007 RCTUBA/BB 000~079
DK40i 000~027 RCTUC/D 000~239
RCTUA 000~031 RCTUE/F 000~335
Hunt From 
PortHunt To 
PortHunt From 
PortHunt To 
PortHunt From 
PortHunt To
PortHunt From 
PortHunt To 
Port
SELECT = Port Number (see legend below)
Enter the RPCI/DIU digital port number of the 
“hunt-from” station.
Enter the port number(s) to which class of 
service must be assigned. To add a port range, 
enter XXX

XXX (low port 
 high port).HUNT TO = (see legend below)
Enter the “hunt-to” RPCI/DIU digital port number.
LED Button 01 deletes a digit from the “hunt-to” 
port. 
						

							System & Station
Program 23 – Built-in Auto Attendant (AA) Primary Announcement Assignments
Strata DK System Record Sheets 5/9935
System & Station
Program 23 – Built-in Auto Attendant (AA) Primary 
Announcement Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:No ports assigned
Program 24 – Built-in AA Secondary Announcement 
Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:No ports assigned
NoteSee Program 23 legend for port ranges.




  6SNU   +ROG  6SNU +ROG 6SNU+ROG
Processor TypePort RangeProcessor TypePort Range
DK14 008~009 RCTUBA/BB 008~079
DK40i 008~027 RCTUC/D 008~239
RCTUA 008~031 RCTUE/F 008~335
Announcement DevicePort Number
1
2
3
4




  6SNU   +ROG  6SNU +ROG 6SNU+ROG
Announcement DevicePort Number
1
2
3
4
SELECT = 1~4
Select the Auto Attendant 
device (digital announcer).AUTO ATT 1 NO. = Port
Enter the standard station logical port 
number to which the device will be assigned.
SELECT = 1~4
Select the Auto Attendant 
device (digital announcer).AUTO ATT 2 NO. = Port
Enter the standard station logical port 
number to which the device will be assigned. 
						

							System & Station
Program 25-1 – Built-in AA Incoming Call Overflow Time
36Strata DK System Record Sheets 5/99
Program 25-1 – Built-in AA Incoming Call Overflow 
Time
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:20 seconds before overflow




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
SELECT = 1 AATT TIME = Seconds before overflowing
Enter the number of seconds, 12~24.