Panasonic Kx Tva50 Installation Manual

							2.Confirm that the VPS power switch is in the "OFF" position, then plug the AC cord into the AC adaptor,
then plug the other end into an AC outlet.
IMPORTANT
KX-TVA50: Use only the included Panasonic AC adaptor, part number PSLP1322.
KX-TVA200 : Use only the included Panasonic AC adaptor, part number PSLP1244 or PSLP1434,
or the KX-A236 Additional AC Adaptor.
Document Version  3.0  2010/06Installation Manual712.12 Connecting the AC AdaptorAC Adaptor
AC Cord
To AC  outlet  
						

							2.13  Securing the CablesThe model shown here is the KX-TVA200, however this procedure is the same for the KX-TVA50.
1. Attach the included strap to either of the 2 rails depending on your preference.
2.Bind the cables as shown.
72Installation ManualDocument Version  3.0  2010/062.13 Securing the CablesRailRail   
						

							3.Attach the cable cover (2.5  Opening/Closing the Covers).
Note
•For safety reasons, do not stretch, bend, or pinch the cables.
• If you prefer, you can cut the other side of the cable cover and run the cables through that opening.
For safety reasons, smooth the cut edges.
Document Version  3.0  2010/06Installation Manual732.13 Securing the CablesCable Cover   
						

							2.14  Initializing the VPS During InstallationBefore programming the VPS for the first time, perform the initialization procedure described below. All settings
are reset to their default values.  Recorded messages are erased.  System prompts (including customized
prompts) are preserved.
1. Turn the power switch to the off position.
2. Set the Mode Switch to position 5 (see 2.3  Names and Locations).
3.Turn the power switch to the on position.
4. Confirm that the  RUN indicator blinks 5 times.
• This may take several minutes. The  ALARM indicator and  RUN indicator will first blink intermittently
before the  RUN indicator blinks 5 times.
5. Turn the power switch off at the VPS.
6. Set the Mode Switch to position 0.
7.Turn the power switch back on at the VPS.
After initializing the VPS, continue with the installation procedure and/or begin programming the VPS.
74Installation ManualDocument Version  3.0  2010/062.14 Initializing the VPS During Installation0
11234 0
11234  
						

							2.15  Wall Mounting
2.15.1  Wall Mounting the VPS
Mounting on a Wooden Wall 1.Place the appropriate wall mounting template (found on the last 2 pages of this manual) on the wall to mark
the locations where the 3 screws need to be placed.KX-TVA50KX-TVA200
2. Install the screws and washers (included) in the wall.
Note
•Drive the screws into the wall until each screw head is the same distance from the wall.
• Install the screws perpendicular to the wall.
3. Mount the unit as shown.
Document Version  3.0  2010/06Installation Manual752.15.1 Wall Mounting the VPS232 mm
(9-1/8 in.)
120 mm (4-3/4 in.) 250 mm
(9-13/16 in.)
130 mm (5-1/8 in.)  Washer
Drive the screw
to this position.   
						

							Note•Do not block the openings of the unit. Allow space of at least 20 cm (8 in.) above and 10 cm (4 in.)
on the sides of the unit.
• Make sure that the wall behind the unit is flat and free of obstructions so that the openings on the
back of the unit will not be blocked.
• Be careful not to drop the unit.76Installation ManualDocument Version  3.0  2010/062.15.1 Wall Mounting the VPS 
						

							Mounting on a Concrete or Mortar Wall
CAUTIONWhen driving the mounting screws into the wall, be careful to avoid touching any metalwork (metal/wire
laths, etc.), conduits, or electrical cables buried in the wall.
1. Place the appropriate wall mounting template (found on the last 2 pages of this manual) on the wall to mark
the locations where the 3 screws need to be placed.
KX-TVA50KX-TVA200
2. Install 3 anchor plugs (user-supplied) in the wall.
3.Install the screws (included) in the wall.
Document Version  3.0  2010/06Installation Manual772.15.1 Wall Mounting the VPS232 mm
(9-1/8 in.)
120 mm (4-3/4 in.) 250 mm
(9-13/16 in.)
130 mm (5-1/8 in.)  Hammer
29 mm
(1-1/8 in.) Anchor Plug
6.4 mm 
(1/4 in.) Drive the screw
to this position.  
						

							4.Mount the unit as shown.
Note
•Do not block the openings of the unit. Allow space of at least 20 cm (8 in.) above and 10 cm (4 in.)
on the sides of the unit.
• Make sure that the wall behind the unit is flat and free of obstructions so that the openings on the
back of the unit will not be blocked.
• Be careful not to drop the unit.
78Installation ManualDocument Version  3.0  2010/062.15.1 Wall Mounting the VPS  
						

							2.15.2  Wall Mounting the AC Adaptor
Mounting on Wooden Wall 1.Place the AC adaptor wall mounting template (found later in this section) on the wall to mark the locations
where the 2 screws need to be placed.KX-TVA50KX-TVA200
2. Install the screws and washers (included) in the wall.
Note
•Drive the screws into the wall until each screw head is the same distance from the wall.
• Install the screws perpendicular to the wall.
3. Mount the AC adaptor as shown.
Document Version  3.0  2010/06Installation Manual792.15.2 Wall Mounting the AC Adaptor83 mm
(3-1/4 in.) 110 mm
(4-5/16 in.) Washer
Drive the screw
to this position.   
						

							Mounting on Concrete or Mortar Wall
CAUTIONWhen driving the mounting screws into the wall, be careful to avoid touching any metalwork (metal/wire
laths, etc.), conduits, or electrical cables buried in the wall.
1. Place the AC adaptor wall mounting template (found later in this section) on the wall to mark the locations
where the 2 screws need to be placed.
KX-TVA50KX-TVA200
2. Install 2 anchor plugs (user-supplied) in the wall.
3.Install the screws (included) in the wall.
80Installation ManualDocument Version  3.0  2010/062.15.2 Wall Mounting the AC Adaptor83 mm
(3-1/4 in.) 110 mm
(4-5/16 in.) Hammer
29 mm
(1-1/8 in.) Anchor Plug
6.4 mm 
(1/4 in.) Drive the screw
to this position.