Panasonic Kx Taw848 Programing Manual

							2.14 [8] ARS
PC Programming Manual 421
Value Range
Max. 10 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.14.8 [8-7] Authorization Code for TRG
Programming Manual References
2.14.6 [8-5] Carrier—Carrier—Modify Command
Feature Manual References
1.1.3 ARS (Automatic Route Selection) 
						

							2.15 [9] CO & Incoming Call
422 PC Programming Manual
2.15 [9] CO & Incoming Call
2.15.1 [9-1] CO Line Settings
CO lines can be assigned a name, and grouped into a maximum of 64 trunk groups.
Physical—Slot
Indicates the slot position of each CO line card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.15.1 [9-1] CO Line Settings
Programming Manual References
None
Feature Manual References
None
Physical—Port
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.15.1 [9-1] CO Line Settings
Programming Manual References
None
Feature Manual References
None 
						

							2.15 [9] CO & Incoming Call
PC Programming Manual 423
CO Name
Specifies the CO line name which is shown on the extensions display when receiving a call from the 
CO line.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.15.1 [9-1] CO Line Settings
Programming Manual References
None
Feature Manual References
1.4.7 Display Information
Trunk Group Number
Specifies the trunk group number to which the CO line belongs.
Default
1
Value Range
1–64
Maintenance Console Location
2.15.1 [9-1] CO Line Settings
Programming Manual References
None
Feature Manual References
1.7.1 GROUP FEATURES
2.15.2 [9-2] DIL Table & Port Settings
Direct In Line (DIL) can be selected for each CO line as the method of distributing incoming CO line 
calls to certain destinations. For each CO line to which DIL distribution is set, different destinations 
can be programmed depending on the time mode (day/lunch/break/night). If desired, Calling Line 
Identification (CLI) distribution can be used in conjunction with DIL distribution. 
						

							2.15 [9] CO & Incoming Call
424 PC Programming Manual
DIL
For each CO line to which DIL distribution is set, different DIL destinations can be programmed 
depending on the time mode (day/lunch/break/night). Generally, DIL distribution is used for CO line 
calls from analog CO lines. Tenant number and VPS trunk group number can also be programmed 
for each CO line.
To assign DIL destination numbers, enter directly or click Destination Setting (see 2.1.6 Extension 
Number Setting).
Slot
Indicates the slot position of each CO line card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None 
						

							2.15 [9] CO & Incoming Call
PC Programming Manual 425
Card Type
Indicates the CO line card type (reference only).
Default
Current card type
Value Range
Card type
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.9.8 INCOMING CALL FEATURES
DIL Destination—Day, Lunch, Break, Night
Specifies the DIL destination in each time mode.
Default
Not stored.
Value Range
Max. 5 digits (consisting of 0–9)
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.4.5 DIL (Direct In Line)
Tenant Number
Specifies the tenant number, to determine the Time Table by which calls are distributed depending 
on the time of day.
Default
1
Value Range
1–8 
						

							2.15 [9] CO & Incoming Call
426 PC Programming Manual
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
2.8.5 [2-4] Week Table
Feature Manual References
1.4.5 DIL (Direct In Line)
1.17.2 Tenant Service
1.17.4 Time Service
VM Trunk Group
Specifies the number of the VPS trunk group sent to the VPS when the DIL destination is the floating 
extension number of a VM (DPT) Group.
The VPS trunk group number is used to allow the VPS to send the applicable greeting message to 
the caller.
Default
1
Value Range
1–48
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.4.5 DIL (Direct In Line)
1.19.4 Voice Mail DPT (Digital) Integration
CLI for DIL
When CLI distribution is enabled for a CO line to which DIL distribution is set, incoming CO line calls 
will be distributed to the CLI destinations (instead of the DIL destinations) if the callers identification 
number is found in the System Speed Dialing Table.
CLI distribution can be enabled or disabled for each time mode (day/lunch/break/night) on a CO line 
basis.
Slot
Indicates the slot position of each CO line card (reference only).
Default
Current slot number 
						

							2.15 [9] CO & Incoming Call
PC Programming Manual 427
Value Range
Slot number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the por t number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None
Card Type
Indicates the CO line card type (reference only).
Default
Current card type
Value Range
Card type
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None 
						

							2.15 [9] CO & Incoming Call
428 PC Programming Manual
Feature Manual References
1.9.8 INCOMING CALL FEATURES
CLI Ring for DIL—Day, Lunch, Break, Night
Enables CLI distribution in each time mode.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.3.10 CLI (Calling Line Identification) Distribution
1.4.5 DIL (Direct In Line)
2.15.3 [9-3] Miscellaneous
The Intercept Routing feature can activate when the destination of an incoming call is unavailable, or 
when there is no destination for the call, to reroute the call to an alternate destination.
Intercept—Intercept Routing - DND (Destination sets DND)
Enables the Intercept Routing—DND feature to activate when the original destination is in DND 
mode.
Default
Enable
Value Range
Disable (Busy Tone): Sends a busy tone to the caller. (However, a call through an LCOT card will ring 
at the original destination while the caller hears a ringback tone.)
Enable: Redirects the call to the intercept destination
Maintenance Console Location
2.15.3 [9-3] Miscellaneous
Programming Manual References
None 
						

							2.15 [9] CO & Incoming Call
PC Programming Manual 429
Feature Manual References
1.4.8 DND (Do Not Disturb)
1.9.9 Intercept Routing
Intercept—Routing to Operator - No Destination (Destination is not 
programmed)
Enables the Intercept Routing—No Destination feature to activate when there is no destination for the 
call. (The Intercept Routing—No Destination feature always works for calls through an LCOT card, 
even when this feature is disabled.)
Default
Enable
Value Range
Disable (Reorder Tone): Sends a reorder tone to the caller
Enable: Redirects the call to an operator
Maintenance Console Location
2.15.3 [9-3] Miscellaneous
Programming Manual References
None
Feature Manual References
1.9.10 Intercept Routing—No Destination
Intercept—Intercept Routing for Extension Call
Enables the Intercept Routing feature to operate for extension calls.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.15.3 [9-3] Miscellaneous
Programming Manual References
None
Feature Manual References
1.9.10 Intercept Routing—No Destination 
						

							2.16 [10] Maintenance
430 PC Programming Manual
2.16 [10] Maintenance
2.16.1 [10-1] Main
SMDR
Station Message Detail Recording (SMDR) automatically records detailed information about 
incoming and outgoing calls.
SMDR Format—Type
Selects the format of SMDR output.
Default
Ty p e  A
Value Range
Type A: 80 digits without call charge information
Type B: 80 digits with call charge information
Type C: 120 digits
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
SMDR Format—Port
Selects the Serial Interface (RS-232C) port that is used to output the SMDR data.
Default
RS-232C 
Value Range
None, RS-232C
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None