Panasonic Kx Taw848 Programing Manual

							2.10 [4] Extension
PC Programming Manual 261
Feature Manual References
None
Intercept No Answer Time—Day, Lunch, Break, Night
Specifies the length of time until an unanswered call is redirected to the intercept routing destination 
in each time mode.
When this setting is set to 0, the system timer is used.
Default
0
Value Range
0–240 s
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.8.4 [2-3] Timers & Counters—Dial / IRNA / Recall / Tone—Intercept Routing No Answer (IRNA)—
Day, Lunch, Break, Night
Feature Manual References
1.9.9 Intercept Routing
Option 1
Slot
Indicates the slot position of each extension card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None 
						

							2.10 [4] Extension
262 PC Programming Manual
Por t
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port
Feature Manual References
None
Extension Number
Specifies the extension number of the extension.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the port is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits.
Default
Starting at 101
(For port 01 of the first extension card that is installed. Extension numbers are preset for subsequent 
extensions by adding one to the previous extension number.)
Value Range
Max. 5 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command
Feature Manual References
None 
						

							2.10 [4] Extension
PC Programming Manual 263
Extension Name
Specifies the name of the extension.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Wireless XDP
Specifies the extension number of the PS with which Wireless XDP Parallel Mode is established. To 
enable Wireless XDP Parallel Mode, the PS must be turned off once and then turned on after 
assigning this setting.
This setting is not available when the software is in Batch mode.
When changing the port type of an extension por t in DPT Type—Type (for Hybrid port) on the 2.7.4 
[1-1] Slot—Extension Port screen, the Wireless XDP setting must be deleted first.
Default
Not stored.
Value Range
Max. 4 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port—DPT Type—Type (for Hybrid port)
Feature Manual References
1.20.3 Wireless XDP Parallel Mode
Ring Pattern Table
Specifies the Ring Tone Pattern Table to be used by the extension.
Default
1 
						

							2.10 [4] Extension
264 PC Programming Manual
Value Range
1–8
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.8.14 [2-8-1] Ring Tone Patterns—Call from CO
2.8.15 [2-8-2] Ring Tone Patterns—Call from Doorphone
2.8.16 [2-8-3] Ring Tone Patterns—Call from Others
Feature Manual References
1.15.2 Ring Tone Pattern Selection
Programmed Mailbox No.
Specifies the mailbox number of the extensions mailbox for Voice Processing Systems (VPS) with 
DTMF Integration.
Default
Same number as the corresponding extension number.
Value Range
Max. 16 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.19.5 Voice Mail DTMF Integration
Transfer Recall Destination
Specifies the transfer recall destination when an extension user transfers a call with the Call Transfer 
without Announcement feature and the transferred call is not answered within a certain time period.
Default
Not stored.
Value Range
Max. 5 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings 
						

							2.10 [4] Extension
PC Programming Manual 265
Programming Manual References
None
Feature Manual References
1.3.8 Call Transfer
ARS Itemized Code
Specifies the itemized billing code used by the ARS feature for identifying calls made from the 
extension for accounting and billing purposes.
Default
Not stored.
Value Range
Max. 10 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.14.6 [8-5] Carrier
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
1.19.1 Verification Code Entry
Option 2
Slot
Indicates the slot position of each extension card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None 
						

							2.10 [4] Extension
266 PC Programming Manual
Por t
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port
Feature Manual References
None
Extension Number
Specifies the extension number of the extension.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the port is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits.
Default
Starting at 101
(For port 01 of the first extension card that is installed. Extension numbers are preset for subsequent 
extensions by adding one to the previous extension number.)
Value Range
Max. 5 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command
Feature Manual References
None 
						

							2.10 [4] Extension
PC Programming Manual 267
Extension Name
Specifies the name of the extension.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Manual C. Waiting for Extension Call
Selects the method of receiving call waiting notification from other extensions.
Default
BSS
Value Range
Off: No notification
BSS: Tone from the handset or built-in speaker
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.3.9 Call Waiting Tone
Automatic C. Waiting
Specifies whether to receive call waiting notifications for calls from a CO line, doorphone calls, and 
calls via an incoming call distribution group.
Default
On 
						

							2.10 [4] Extension
268 PC Programming Manual
Value Range
Off, On
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.3.9 Call Waiting Tone
Pickup Dial Set
Sets or cancels the Hot Line feature. The number specified in Pickup Dial Number on this screen is 
dialed automatically after going off-hook when the Hot Line feature is active.
Default
Off
Value Range
Off, On
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.8.4 [2-3] Timers & Counters—Dial / IRNA / Recall / Tone—Dial—Hot Line (Pickup Dial) Start
Feature Manual References
1.8.6 Hot Line
Pickup Dial Number
Specifies the number to be dialed automatically after going off-hook when the Hot Line feature is 
active.
Default
Not stored.
Value Range
Max. 32 digits (consisting of 0–9, *, #, T [Transfer], [ ] [Secret], P [Pause], and F [Flash])
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None 
						

							2.10 [4] Extension
PC Programming Manual 269
Feature Manual References
1.8.6 Hot Line
Data Mode
Sets or cancels the protection against tones or interruptions from other extensions during 
communication.
Default
Off
Value Range
Off, On
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.4.1 Data Line Security
Option 3
Slot
Indicates the slot position of each extension card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the por t number (reference only). 
						

							2.10 [4] Extension
270 PC Programming Manual
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port
Feature Manual References
None
Extension Number
Specifies the extension number of the extension.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the port is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits.
Default
Starting at 101
(For port 01 of the first extension card that is installed. Extension numbers are preset for subsequent 
extensions by adding one to the previous extension number.)
Value Range
Max. 5 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command
Feature Manual References
None
Extension Name
Specifies the name of the extension.