Panasonic Electronic Board UB-T780 Operating Instructions

							2.
Assemble the stand. Notice
•Do not over-tighten the screw ( ). (Doing so can warp the support beams.)
• Assemble the stand so that the locking casters are on the rear side. Operating Instructions (For Basic Operations) 39 1
Installation ManualREAR
FRONT
Assemble with the holes 
toward the front.
Locking caster
side (rear) Locking 
caster side
(rear)   
						

							3.
Pull the fall-prevention extension legs down. Note
•When folding back the fall-prevention extension legs, release the lock as follows ( ,
).
4.
Mount the elite Panaboard.
See "Assembling the elite Panaboard" (For Mounting on a Stand (Sold Separately)  ® page 44).40 Operating Instructions (For Basic Operations)
Installation Manual2
1 1 2 1
1 2  
						

							Assembly Instructions
Preparing for Removing the elite Panaboard from Its Packaging
Open the box, remove the accessory box, and open the plastic cover of the elite Panaboard. Notice
•When handling the screen board, hold it by the edge frame and not the screen board itself.
(Holding the screen board can result in damage.)
• The packing materials in the shipping box are necessary
 for repackaging, so keep them in a safe place. Operating Instructions (For Basic Operations) 41 1
Installation ManualShipping Box
Shipping Box
Electronic Board
[Accessory Box Contents]
•  Power Cord  1
  USB Cable 1
  CD-ROM 1
  Cable Holder  1
  Wall Mounting Plate  
(Right, Left)  1
  Battery 1
  Electronic Pen  1
  Penpoint 2 
  Cable Tie  1
  Operating Instructions  1
  Warranty 1..............
.............
...................
...........
................ ................
............ ...............
................
................
.....  
						

							Assembling the elite Panaboard
For Wall Mounting
1.
Loosely wrap the power cord with the cable tie,
and plug the power cord into the AC inlet.
•Connect the power cord to the elite Panaboard
before installing on a wall. 2.
Insert the end of the cable tie into the cable tie
fastening hole on the lower frame cover. 3.
Pull the loose end of the cable tie to tighten it,
and install the power cord depending on the
location of the outlet, as illustrated in the
following diagrams.
•When attaching the power cord downward. •
When attaching the power cord along the lower
side of the elite Panaboard. 42 Operating Instructions (For Basic Operations)
Installation ManualPower Cord
1
2  Fasten the power cord
with the cable tie. Fasten the power 
cord with the cable tie.  
						

							4.
Hang the elite Panaboard on the wall mounting
plates with the screw heads. 5.
Remove the lower frame cover.
Remove the left and right screws, and then remove
the
 lower frame cover from the main unit of the elite
Panaboard. 6.
Remove the 4 latches from the board
attachment by pushing them towards the rear. 7.
Fasten to the wall.
Using the remaining 4 screws, securely fasten the
lower portion of the board attachment to the wall. 8.
Reattach the lower frame cover.
Attach the lower frame cover to the lower side

 of the
elite Panaboard, and tighten both left and right
screws so that the cover does not protrude. Notice
•Take care not to injure yourself on the board
attachments when attaching the lower
frame cover. Operating Instructions (For Basic Operations) 43 1
Installation Manual Lower Frame Cover Latches
Board Attachment   
						

							•
When mounting on a wall, do not hit or jolt
the elite Panaboard.
• After mounting, gently apply some weight
on the elite Panaboard to make sure that it
is securely fastened to the wall. Note
•After installation is complete, use the
included cable holder to manage the power
cord and USB cable.
9. Wipe the screen board surface.
Gently wipe the screen board surface with a soft,
moist cloth. Notice
•Do not use thinner, benzene, or abrasive
chemicals to clean.
(Doing so can result in discoloration.)
• Do not wipe the screen board with a dry
cloth.
(Doing so can cause static electricity build-
up.)
10. Confirm that the elite Panaboard can operate.
See "Confirming the elite Panaboard
Operation" (page 46). For Mounting on a Stand (Sold Sep-
arately)
1.
Attach the power cord.
•Connect the power cord to the elite Panaboard
before installing on the stand. 2.
Depending on the location of the outlet, install
the power cord as illustrated in the following
diagrams.
•When attaching the power cord downward. •
When attaching the power cord along the lower
side of the elite Panaboard. 44 Operating Instructions (For Basic Operations)
Installation Manual Power Cord    
						

							3.
Hang the elite Panaboard on the stand with the
screw heads. 4.
Secure the elite Panaboard to the stand frame
using the two-wing bolts (M5  ´ 12 mm [1
/2 in.] [2
count]) included with the stand. Note
•After installation is complete, use the
included cable holder to manage the power
cord and USB cable. •
When installing the elite Panaboard on the
stand, you can adjust its height to 4 different
levels.
When changing the height, remove the left
and right screws from the back of the elite
Panaboard,
 and securely insert them at the
desired height. Torque (greater than 98 N·m
[10 kgf·cm (9 lbf·in.)]).
elite Panaboard Height Screw Position
-100 mm (-4 in.) Highest
Standard 2nd from top
+100 mm (+4 in.) 2nd from bottom
+200 mm (+7 
7
/8 in.) Lowest
5.
Wipe the screen board surface.
Gently wipe the screen board surface with a soft,
moist cloth. Notice
•Do not use thinner, benzene, or abrasive
chemicals to clean.
(Doing so can result in discoloration.)
• Do not wipe the screen board with a dry
cloth.
(Doing so can cause static electricity build-
up.)
6. Confirm that the elite Panaboard can operate.
See "Confirming the elite Panaboard
Operation" (page 46). Operating Instructions (For Basic Operations) 45 1
Installation Manual    
						

							Confirming the elite Panaboard Operation
After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.
Action Checkpoints
Operation Measure
1 Turn on the power Green LED lights. (Normal operation)
Green LED does not light, or
red LED is blinking. Check the power cord.
See "Assembling the elite
Panaboard" (For Wall Mount-
ing ® page 42, For Mounting
on a Stand (Sold Separately)
® page 44) step 1.
Confirming the Interactive Features
1.Following the procedure in "Installing the elite Panaboard software"
 (page 17), install the software
and, and connect the included USB cable.
2. Confirm that the interactive features are operating correctly.
•If a projector is not available, confirm operation using only the elite Panaboard and computer.
• When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
• Perform tentative calibration by pressing the 4 points on the elite Panaboard with the electronic pen,
as shown in the illustration below.
For precise adjustment, it is necessary to use a projector. •
With the elite Panaboard software running, enter White Background mode and select the marker tool.
Confirm operation by writing on the screen board

 with the electronic pen and checking that the writing
is displayed on the computer's screen. (Your writing with the electronic pen will not appear on the
screen board itself.) 46 Operating Instructions (For Basic Operations)
Installation ManualApprox. 
100 mm (4 in.) Approx. 100 mm (4 in.)
1
34
2  
						

							Repackaging
To repackage the elite Panaboard, perform steps in "Assembling the elite Panaboard" (For Wall Mounting  ®
page 42, For Mounting on a Stand (Sold Separately) ® page 44) in reverse. Package the unit as depicted in
the diagram in "Preparing for Removing the elite Panaboard from Its Packaging " (page 41).Notice
•When handling the screen board, hold it by the frame and not the screen board itself. (Holding the
screen board can result in the damage.) Operating Instructions (For Basic Operations) 47 1
Installation Manual 
						

							© 2007 Panasonic Communications Co., Ltd. All Rights Reserved.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic 
products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where 
they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your 
products to your local retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative 
effects on human health and the environment which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
Panasonic Communications Company of North America
Unit of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
Matsushita Electric Industrial Co., Ltd.
http://panasonic.net/ Panasonic Business Systems U.K.
A Division of Panasonic U.K. Ltd.
Willoughby Road, Bracknell, Berkshire, RG12 8FP
Panasonic Marketing Europe GmbH
Hagenauer Strasse 43
65203 Wiesbaden, Germany
For information of Compliance with EU relevant Regulatory
Directives, Contact to Authorised Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
(For EU only)