Panasonic Electronic Board UB-T780 Operating Instructions

							Set the Proper Resolution
•
Set your computer's and projector's resolutions to
the most appropriate setting.
If the resolution is not set properly, the image
 will be
difficult to see. Particularly, if the projector's
resolution is lower than the computer's, thin lines
can appear cut or broken. Refer to your projector's
documentation for information on adjusting the
resolution.
Do Not Look Directly into the Projector Lamp
• When using a projector, try to avoid looking directly
into the projector lamp. Doing so can hurt your eyes. Setting Your System (Cal-
ibration)
About Calibration
Calibration is setting up the elite Panaboard and
projector so that lines and comments drawn on the
screen board with the electronic pen will be correctly
displayed on the image projected onto the screen
board. Be sure to perform calibration before use.
After you have set up the elite Panaboard, project an
image onto the screen board and use the elite
Panaboard software installed on your computer to
perform calibration.
After Calibration
Do Not Move the elite Panaboard or the Pro-
jector
•
The position of projected image and electronic pen
will become misaligned in the following cases,
requiring you to re-calibrate their positions.
–The location of the projector changed.
– The location of the elite Panaboard changed.
– The image
 area or placement was changed due
to changes in the zoom, focus, etc.
– The resolution of the projector or the computer
changed.
• If you are using the elite Panaboard installed on a
stand, be aware that accidentally hitting the elite
Panaboard or pushing too strongly with the
electronic pen while operating. Doing so can move
the stand's position, which will result in
misalignment of the projected image and the
electronic pen's position.
• Make sure to lock the stand’s casters when using
the elite Panaboard, as failing to do so can cause
misalignment. Operating Instructions (For Basic Operations) 19 1
Usage 
						

							Starting the elite Pana-
board software and Per-
forming Calibration
1.
Turn on the elite Panaboard.
2. Connect the elite Panaboard to your computer
with the USB cable.
•The elite Panaboard software starts
automatically.
• When you start the elite Panaboard software for
the first
 time, the calibration screen is displayed.
• Restart your computer if you are prompted to do
so. After the computer has restarted, connect
the elite Panaboard to your computer with the
USB cable.
3. Perform calibration.
4. Press the electronic pen in the center of the 4
points in each corners of the display for 2
seconds, in the order shown in the illustration. •
Hold and press the electronic pen at a right
angle to the screen board.
• When you push down on the penpoint, the
electronic pen will make a buzzing sound.
• When the position of the indicated point has
been determined correctly, calibration will
automatically move to the next point.
• When calibration has finished normally, a
completion dialog box will be displayed.
5. Click [OK].
•If the elite Panaboard and projector are fixed so
that they will not move, select the [Always use
this calibration information.] check box, and
click [OK] to skip calibration from the next time
you start the elite Panaboard software.
• After

 calibration has completed, the   icon will
be displayed in the notification area, and the
Desktop Drawing Tool is automatically
displayed. [Desktop Drawing Tool]
• You will be able to use elite Panaboard
software. 20 Operating Instructions (For Basic Operations)
Usage12
34     
						

							Note
•For detailed information about using the
elite Panaboard software, refer to the
included electronic manual or the help. For
instructions on viewing the electronic
documentation "Operating Instructions (For
Software)", see "Viewing the Electronic
Documentation" (page 22).
Exiting the elite Panaboard software
Right-click on the   icon in the notification area, and
select [Exit] from the menu. Uninstalling the elite
Panaboard software
If it is necessary to uninstall the elite Panaboard
software, follow the procedure below.
1.
Turn on your computer and start Windows.
•Log into an account with Administrator
privileges.
2. Select [Add or Remove Programs] from the
Control Panel.
•In Windows 2000, select [Add/Remove
Programs].
• In Windows Vista, select [Uninstall a program].
3. Select Panasonic elite Panaboard, then remove
it.
4. Follow the on-screen instructions.
5. When uninstallation is complete, restart your
computer. Operating Instructions (For Basic Operations) 21 1
Usage  
						

							Viewing the Electronic
Documentation
Follow the procedure below to view the electronic
documentation "Operating Instructions (For Software)".
1.
Turn on your computer and start Windows.
2. Open "Operating Instructions (For Software)"
from the Start menu.
([Start]  ® [All Programs]  ® [Panasonic]  ® [elite
Panaboard] 
® [Operating Instructions for
Software])
• The electronic documentation will be displayed. Note
•To view the electronic documentation, you
must have Adobe ®
 Reader ®
 installed on
your computer. If your computer is
connected to the Internet, you can
download Adobe Reader from Adobe’s web
site. 22 Operating Instructions (For Basic Operations)
Usage 
						

							Daily Care
When cleaning the elite Panaboard or inside the elite  Panaboard, make sure to switch off the power and unplug
the power cord from the AC outlet.
Cleaning the elite Panaboard Gently wipe the elite Panaboard with a soft, moist cloth.
Notice
•For spots that are difficult to remove, use
commercially available white-board cleaner or
neutral household cleaner diluted with water.
• The elite Panaboard is designed exclusively for
projector images. If you write on the screen
board with a white-board marker, you cannot
erase it with a standard eraser. Use a
commercially available melamine foam eraser
to erase.
• Do not wipe the screen board with a dry cloth.
(Doing so can cause static electricity build-up.)
• Do not use thinner, benzene, or abrasive
chemicals to clean.
(Doing so can result in discoloration.) Replacing the Battery in the
Electronic Pen
When the charge in the battery in the electronic pen is
low, the message, "The pen battery is low. Replace

 the
battery soon." will be displayed on the computer screen.
Continued use of the electronic pen can lead to poor
performance. Replace the battery as soon as possible.
See "Inserting (Exchanging) Batteries" (page 14) for
details on replacing the battery.
• Promptly remove used batteries and properly
dispose of them following your local laws and
regulations. Operating Instructions (For Basic Operations) 23 1
Appendix
Appendix Após o uso as pilhas / baterias 
contidas neste produto poderão 
ser dispostas em lixo doméstico.
For Brazil Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg ziju, moet u ze niet
weggooien maar inleveren als KCA.
For Netherlands
Niet weggooien,
maar inleveren
als KCA.NLNL For Taiwan   
						

							Replacing the Penpoint of the
Electronic Pen
As the penpoint of the electronic pen becomes worn,
 a
hole will appear in the penpoint. Continuing to use the
electronic pen in this condition can cause damage to
the screen or unsatisfactory operation, so replace the
penpoint with a new one. 24 Operating Instructions (For Basic Operations)
Appendix  
						

							Troubleshooting
When you think there may be a problem, follow the steps in the table below. If the problem persists, contact
your dealer.
Symptom Possible cause and solution See page
The LEDs do not light when
the power switch is turned
on. Check that the power cord is properly plugged in.
→
If the problem persists, turn off the power, and then turn it on
again. –
Red LED is blinking. Turn off the power, and turn it on again.
→
If the problem persists, contact your dealer. –
The computer does not rec-
ognize the elite Panaboard. •
The USB cable is connected to a USB hub.
→ Do not connect the elite Panaboard through a USB hub.
• Check that the elite Panaboard is in an operable
 state, and that
the USB cable is properly connected. –
The connection between
the computer and the elite
Panaboard is unexpectedly
lost.
Check that the elite Panaboard is in an operable state, and that the
USB cable is properly connected.
–
The electronic pen's posi-
tion is not correct. The projected image is misaligned.
→
Perform the calibration again. 20
Drawn lines and comments
are not completely dis-
played or are displayed in
the wrong location. •
You are holding the electronic pen at an angle.
• You are operating the elite Panaboard in direct sunlight

 or other
strong lighting.
• Infrared controllers (e.g., a television remote control) are being
used and pointed towards the position sensor.
• There is a wall or ceiling close to the sides of the elite Pana-
board.
• There is an air-conditioner vent close to the elite Panaboard.
• A plasma television is being used close to the elite Panaboard.
• Part of the position sensor is blocked.
• You are covering part of the electronic pen's sensor with your
hand.
• Several electronic pens are being used at the same time.
• The electronic pen is low on batteries.
→ Check that none of the above is causing the problem.
If misalignment is not caused by any of the above, perform the
calibration again. –
Extra lines are displayed on
the computer screen. Apart from writing directly on the elite Panaboard with the electronic
pen, you pushed the penpoint with your finger while

 holding it close
to the elite Panaboard.
→ Avoid pushing the penpoint with your finger. –
Operating Instructions (For Basic Operations) 25 1
Appendix 
						

							Symptom Possible cause and solution See page
The message "The pen bat-
tery is low. Replace the bat-
tery soon." is displayed on
the computer screen.
Replace the electronic pen's battery with a new one. 14
23
Marks written with a white-
board marker cannot be
erased. Because the elite Panaboard is designed exclusively for projector
images, you cannot erase the marks with a standard eraser.
→
Use a commercially available melamine foam eraser to erase. 23
26 Operating Instructions (For Basic Operations)
Appendix 
						

							Specifications
Model Number UB-T780
General Power AC 100 V–240 V, 50 Hz/60 Hz
Power Consumption: During
Operation 0.1 A
External Dimensions: Height ×
Width × Depth 1340 mm × 1752 mm × 89 mm
(4 ft. 4 
7
/8 in. × 5 ft. 9  1
/8 in. × 3  1
/2 in.) Weight 26 kg (57.32 lbs)
Operating Environment Temperature: 15 °C to 30 °C (59 °F to 86 °F)
Humidity: 30 % to 80 %
Storage Environment Temperature: -20 °C to 40 °C (-4 °F to 104 °F)
Humidity: 15 % to 80 %
Interface USB 2.0
Input Unit Screen Board Size: Height ×
Width 1175 mm × 1692 mm
(3 ft. 10 
3
/8 in. × 5 ft. 6  3
/4 in.) Interactive
Features Effective Area:
Height × Width 1165 mm × 1502 mm (3 ft. 10 in. × 4 ft. 11 
1
/4 in.)
Project the image so that it is at least  5 mm (1
/4  in.) from the
screen frame. The electronic pen may not function correctly
within 50 mm (2 in.) of the position sensor in the upper-left
corner of the screen board. Electronic Pen Power LR03 (AAA alkaline dry cell battery) × 1
Electronic Pen Battery Life 30 hours (when used continuously at 25 °C [77 °F])
* When using Panasonic LR03 alkaline dry-cell batteries.
Operating Instructions (For Basic Operations) 27 1
AppendixProjectable Area
5 mm (1/4 in.)
5 mm
(1/4 in.)
50 mm (2 in.)
5 mm (
1/4 in.)  
						

							Optional Devices and Accessories
Optional Device Stand KX-B061
Accessories Electronic Pen UE-608025
•
To purchase separately sold items, contact your dealer. 28 Operating Instructions (For Basic Operations)
Appendix