Panasonic Electronic Board UB-T780 Operating Instructions

							When disposing of the battery, cover the
battery contacts with insulation (ex. tape).
Direct contact with other
 batteries may re-
sult in leaking, fire, or explosion. Do not solder the battery, as it may result
in the battery leaking, generating heat, or
bursting.
Power
When the unit is not used over an exten-
ded period of time, switch it Off and unplug
it. If an unused unit is left connected to a
power source for a long period, degraded
insulation may cause electric shock, cur-
rent leakage or fire.
The unit should be used only with the pow-
er cord enclosed with the unit.
Installation and Relocation Do not position the unit in a location where
it is unstable.
Do not place the unit in a hot humid or
dusty environment. Prolonged exposure
to these adverse conditions may cause
fire or electric shock.
To prevent fire or shock hazard, do not ex-
pose this unit to rain or any type of mois-
ture. When moving the unit, be sure to unplug
the power cord from the AC outlet. If the
unit is moved with the power cord attach-
ed, it can cause damage to the cord which
could result in fire or electric shock.
After installing or moving the unit, lock the
casters and set the fall-prevention exten-
sion legs.
Move this unit with two persons. Other-
wise, this unit may fall down and cause
injury.
Operating Safeguards If the unit is fallen down or damaged, turn
the unit off and unplug the power cord.
Otherwise, it may cause fire or electric
shock.
Do not lean against the screen or on the
cover (lower), even if the unit is mounted
on the wall.
Battery When the unit is not used over an exten-
ded period of time, take the batteries out
of the unit. Otherwise, the batteries may
leak. Do not use the leaked batteries.
Operating Instructions (For Basic Operations) 9 1
For Your Safety  CAUTION        Locking the casters
(Push this side)
Push to lock      
						

							Safety Information (For
United Kingdom Only)
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 5 amp. fuse is fitted in this plug.
 Should the fuse need
to be replaced please ensure that the replacement fuse
has a rating of 5 amps. and that it is approved by ASTA
or BSI to BS1362. Check for the ASTA mark   or the
BSI mark   on the body of the fuse. If the plug contains
a removable fuse cover you must ensure that it is
refitted when the fuse is replaced. If you lose the fuse
cover the plug must not be used until a replacement
cover is obtained. A replacement fuse cover can be
purchased from your local Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket
outlet in your home then the fuse should be removed
and the plug cut off and disposed of safely.
There is a danger of severe electrical shock if the cut
off plug is inserted into any 13 amp. socket.
If a new plug is to be fitted please observe the wiring
code as shown below. If in any doubt please consult a
qualified electrician.
WARNING: This appliance must be earthed.
IMPORTANT: The wires in this mains lead are col-
oured in accordance with the follow-
ing code.
Green-and Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this
appliance may not correspond with the coloured
markings identifying the

 terminals in your plug, proceed
as follows.
The wire which is coloured Green-and-Yellow must be
connected to the terminal in the plug which is marked
with the letter E or by the Earth symbol   or coloured
Green or Green-and-Yellow.
The wire which is coloured Blue must be connected to
the terminal in the plug which is marked with the letter
N or coloured Black.
The wire which is coloured Brown must be connected
to the terminal in the plug which is marked

 with the letter
L or coloured Red. How to replace the fuse:
Precautions
About Using the Battery
If a battery is used improperly, the battery may leak,
causing corrosion of the unit, or it may burst.

 To prevent
this, always follow the precaution given below.
• If the electronic pen ceases to function because the
battery has run out, remove it immediately and
dispose of it according to local regulations.
Leaving a drained battery in the electronic pen may
result in leakage.
About Disposing of the Battery 10 Operating Instructions (For Basic Operations)
For Your Safety   Open the fuse
compartment with a
screwdriver and replace 
the fuse. Após o uso as pilhas / baterias 
contidas neste produto poderão 
ser dispostas em lixo doméstico.
For Brazil Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg ziju, moet u ze niet
weggooien maar inleveren als KCA.
For Netherlands
Niet weggooien,
maar inleveren
als KCA.NLNL For Taiwan   
						

							Included Accessories
Check that all of the following items are included with your elite Panaboard.
In the event that an item is missing, please contact your dealer.
List of Accessories Power Cord
(3 m [9 ft. 10  3
/8 in.]) 1 USB Cable
(5 m [16 ft. 5  3
/8in.]) 1 Software CD-ROM 1
AAA Battery (LR03)
(Disposable) 1 Electronic Pen 1 Penpoint
(Replacement) 2
Operating Instructions
(For Basic Operations) (this document) 1 Warranty 1
Note
•The illustration of the power cord shown above is for the United States. The shape of the plug may
vary depending on country/area.
• Stand is sold separately.
• Store the extra penpoint along with this operating manual.
About Using the CD-ROM To prevent damage to the CD-ROM:
•
Do not touch or write on the surface of the disc.
• Do not leave the disc out of the protective case.
• Do not leave the disc in the direct sunlight or near heat sources.
• Do not place heavy objects on the disc case or drop the case.
• To clean the disc, hold the disc by its
 edges and wipe it from the center to the edges with a dry, soft cloth. Operating Instructions (For Basic Operations) 11 1
Usage
Usage         
						

							Names and Uses of the Parts
Screen
Front View Rear View
12 Operating Instructions (For Basic Operations)
UsagePosition Sensor
Detects the position of the electronic pen. Do 
not block the sensor while operating the elite
Panaboard.
Screen Board
Project the contents of a computer screen using a 
projector.
Power Switch
Pen Tray
Push the center of the door to open the pen tray, 
which can hold up to 2 electronic pens.
Status LEDs
Left: Power LED (green)
Lights green when the power is on.
Right: Error LED (red)
Lights red when an error occurs. 
USB Port
Directly connect a computer using a USB cable 
(included). AC Inlet
Power Cord  
						

							Notice
•The elite Panaboard is designed exclusively for projector images. Do not write on the screen board
with a white-board marker. If you write on the screen board with a white-board marker, you cannot
erase it with a standard eraser. Use a commercially available melamine foam eraser to erase.
Electronic Pen Notice
•Use the electronic pen by holding it at a right angle to the screen board.
Holding it at an angle can cause its position to be read incorrectly.
• Do not use multiple pens at the same time. This can result in erroneous operation.
• Do not push the penpoint while holding the pen close to the elite Panaboard. Doing so can cause
erroneous behavior. Note
•The electronic pen switches to power-save mode after about 30 minutes.
• When waking up the pen from power-save mode by pushing the penpoint, the pen’s reaction may be
slow.
• When operating the electronic pen, you will hear a buzzing sound due to the pen emitting ultrasonic
waves for location detection. This sound does not have any negative effects for nearby people or
devices. It will not cause electrical shocks. Operating Instructions (For Basic Operations) 13 1
UsagePenpoint
When you push down on the penpoint, ultrasonic waves 
and infrared signals are transmitted, and equivalent of a 
left mouse click is performed.
Ultrasonic Emitter
Do not block this area with your fingers.
Doing so will prevent the elite Panaboard from correctly 
detecting the electronic pens position.
Infrared Emitter
Do not block this area with your fingers.
Doing so will prevent the elite Panaboard from correctly 
detecting the electronic pens position.
Pen Button
Performs the same function as a right-click with a mouse.
Battery Cover  
						

							Inserting (Exchanging) Batteries
1. Remove (replace) the battery cover. •
When replacing the cover, follow the procedure in
reverse. 2. Insert (exchange) the battery and replace the
cover.
•
Make sure to use a AAA alkaline battery, and
ensure that   and   face the correct direc-
tions. 14 Operating Instructions (For Basic Operations)
Usage     
						

							Connecting External Components
1.Set the power switch to "O" (OFF), connect the power cord (included) to the elite Panaboard, and
plug the power cord into an AC outlet. •
Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is
easy to unplug.
• If you are using the optional stand, plug the power cord into the AC inlet, and secure the cord
as shown in the illustrations below.
When attaching the power cord down-
ward. When attaching the power cord along the lower side of
the elite Panaboard.•
About Grounding
If you cannot connect the grounding line, contact your dealer. The cost of installing a grounding
connection is not included in the price of the elite Panaboard.
• The included power cord is exclusively for use with
 the elite Panaboard. Do not use it with any
other devices. Operating Instructions (For Basic Operations) 15 1
UsagePower Switch
(ON)
(OFF)
Rear
Power Cord
 (Included)
Power Cord    
						

							2.
Connect the elite Panaboard to a computer using the USB cable (included).
•elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port.
Computer: Plug the A connector (larger connector) into a USB port on the computer.
• Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation. 3.
Connect the computer to a projector.
•For instructions on connecting your computer and projector, refer
 to the respecting instruction manuals.
About the Usage Location •Do not place the elite Panaboard where it is directly exposed to sunlight, near a stove, near to a heating/
cooling vent or exposed to strong winds.
• Do not use the elite Panaboard in a location less than 10 °C (50 °F) or in a location subject to extreme
changes in temperature. Note
•If you use the elite Panaboard under the conditions

 above, there is a risk that the elite Panaboard will
not operate correctly.
Moving the elite Panaboard When Using the Stand (Sold Separately) 1.Make sure that the power switch is set to "O" (OFF), and disconnect the power cord and USB cable.
2. Release the locks on the casters.
3. Move the elite Panaboard, taking care not to bang or shake it. Notice
•Always move the elite Panaboard with 2 people.
• Do not drag or step on the cable.
4. Lock the casters. 16 Operating Instructions (For Basic Operations)
UsageUSB Cable
(Included)
Video CableProjector
Computer To USB Port
AC
AC  
						

							Installing the elite Pana-
board software
You need to install the elite Panaboard software on
 the
computer that will be used with the elite Panaboard.
To install the elite Panaboard software, follow the
procedure below. Notice
•Do not connect the USB cable until the
installation is completed.
• Do not connect more than 1 elite Panaboard to
the same computer.
(Doing

 so can cause erroneous behavior on the
computer.)
1. Turn on your computer and start the
Windows *1
 operating system.
• Log into an account with Administrator
privileges.
*1 Windows refers to the Microsoft ®
 Windows ®
 operating
system.
2. Insert the included CD-ROM into the CD-ROM
drive.
•The setup screen will be displayed.
• If the setup screen does not appear, select your
CD-ROM drive in Explorer and double-click
"Menu.exe".
• In Windows Vista, if the Autoplay dialog box is
displayed, click [Run Menu.exe].
3. When the "Welcome" screen has been
displayed, click [ Next].
4. Click [Install elite Panaboard]. 5.
If you agree to the terms in the "License
Agreement", click [Yes].
•In Windows Vista, if the "User Account Control"
window is displayed, click [Continue] to
continue with the installation.
6. When the

 following screen is displayed, confirm
that the USB cable is not connected to your
computer or the elite Panaboard, and click [OK].
• If the USB cable is connected to the elite
Panaboard, disconnect the cable, and click
[OK].
• If .NET Framework 1.1 or later is not installed,
an installation screen will be displayed. Follow
the on-screen directions to install these
components. 7.
When the installation wizard is displayed, follow
the on-screen instructions and continue with
the installation.
8. When installation has finished, click [Finish].
•Restart your computer if you are prompted to

 do
so.
• The group [elite Panaboard] will be created in
the [Panasonic] group in the program menu.
• The following items will appear in the [elite
Panaboard] group:
–elite Panaboard software
– elite Panaboard book
– Operating Instructions for Basic Operations
– Operating Instructions for Software Operating Instructions (For Basic Operations) 17 1
Usage   
						

							Setting the Projector
Set up your projector as instructed below.
About Positioning the Image
•
When you are projecting an image, make sure that
the edge of the projected image is at least 5 mm
(1
/
4 in.) from the screen frame. The electronic pen
may not function correctly within 50 mm (2 in.) of the
position sensor in the upper-left corner of the screen
board. Project the Image as a Rectangle
•
Adjust the location of the projector to project at a
right angle with the elite Panaboard. •
If the image is projected trapezoidally, the position
of the electronic pen may not be read correctly.
Adjust the projector so that the projected image is
a rectangle. Refer to your projector's
documentation for information on adjusting the
projected image. 18 Operating Instructions (For Basic Operations)
UsageProjectable Area
5 mm (1/4 in.)
5 mm
(1/4 in.)
50 mm (2 in.)
5 mm (
1/4 in.)