Panasonic Aj Lt95 Operating Instructions Manual

							The underlining indicates the factory setting.30 MENU LOCK
0000
0001OFFONThis selects the setup menu lock mode.
0: The lock is released (enabling changes to be made).
1: The lock is engaged (prohibiting changes).
70 P.ON LOAD
0000
0001OFFONThis is for establishing the setting that changes the setup menu
settings to the user’s initial settings when the power is turned on.
0: The setup menu settings remain unchanged.
1: The setup menu settings are changed. 11 SYS SC 0000
0127
0255–127
0
128This is for adjusting the system phase.  The total variable range is
at least ±180 degrees.
–: The phase is advanced.
+: The phase is delayed.
17 SYS H RANGE
0000
0001FULL
FINEThis selects the SYSTEM H variable range.
0: ±8 µs
1:–2.0 µs to +2.7 µs 13 VIDEO PHASE 0000
0032
0064–32
0
32This is for adjusting the video signal phase (in 148 ns steps).
–: The phase is advanced.
+: The phase is delayed.
18 SYS H OFFSET
0000
0001
0002
0003
0004
0005
0006–3
–2
–1
01
2
3This selects the SYSTEM H center position.
0:–13.4 µs
1:–8.96 µs
2:–4.52 µs
3: 0 µs
4: +4.52 µs
5: +8.96 µs
6: +13.4 µs
16 AV PHASE 0000
0090
0180–90
0
90This is for adjusting the phase of the audio output with respect to
the video output signals (in 20.8 µs steps).
–: The audio output phase is advanced ahead of the video output.
+: The audio output phase is delayed from the video output.
[[ [[
[
[ [[
[[
[[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
31
Setup menus
SYSTEM menu 
						

							[ [[
The underlining indicates the factory setting.001 LOCAL ENA
0000
0001
DIS
ST&EJ
This selects the switches which can be operated on the control
panel when the CONTROL switch has been set to the REMOTE
position.
0: None of the switches or buttons can be operated.
1: Only the STOP (ALL STOP) and EJECT buttons can be
operated.
003 REMAIN SEL
0000
0001
OFF
ON
This selects whether the REMAIN (remaining tape time) display is
to be superimposed on the MONITOR OUT connectors and liquid
crystal monitor screen.
0: REMAIN display is not shown.
1: REMAIN display is shown.
 
OREMAIN display is not shown when the tape has been ejected
or when the remaining tape time is calculated after the tape has
been inserted.
OIt is not shown when TIME has been selected as the setup
menu item No.008 (DISPLAY SEL) setting.
OIt is not shown when tape start or tape end is detected and BOT
or EOT is displayed. 002 TAPE TIMER
0000
0001±12h24hThis selects the time system displayed on the CTL counter.
0: The time is displayed using the 12-hour time system.
1: The time is displayed using the 24-hour time system.
008 DISPLAY SEL
0000
0001
0002TIME
T&STAT&S&MThis selects what display is to be superimposed on the MONITOR
OUT connectors and liquid crystal monitor screen.
0: Counter value is displayed.
1: Counter value and operation mode are displayed.
2: In addition to the counter value and operation mode, the
remaining tape, tape format and error messages are displayed.
013 PB FORMAT
0000
0001MANUALAUTOThis selects the format used for tape playback.
0: The format corresponds to what is selected as the setup menu
item No.012 (SYS FORMAT) setting.
1: The format corresponds to the format of the recording on the
tape.
 
OInternal operation for VTR2 is forcibly set to MANUAL when an
editing mode has been selected.
OThe automatic 525i/625i setting is not performed.[[
[[
070 TV SYSTEM
0000
0001525625This selects the TV system.
0: The 525 interlace/59.94 Hz system is selected.
1: The 625 interlace/50 Hz system is selected.

When this setting is changed, it is stored in the memory, and it
takes effect when the power is turned off and back on again.[ 011 CHARA TYPE
0000
0001WHITEW/OUTThis selects the type of characters to be used for the
superimposed display on the VIDEO MONI OUT connector and
for the setup menus.
0: White characters on a solid black background
1: White characters with black borders[ [[
[[
012 SYS FORMAT
0000
000150M25MThis selects the recording and playback format.
0: DVCPRO50 (50 Mbps) is selected.
1: DVCPRO25 (25 Mbps) is selected.[[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
32
Setup menus
BASIC menu 
						

							The underlining indicates the factory setting.[[ 100 SEARCH ENA
0000
0001DIALKEYThis selects the direct search operation.
0: Direct search mode
1: Non-direct search mode (search dial operations are
acknowledged only in the STILL mode).
102 FF. REW MAX
0000
0001
0002x16
x32x50This selects the maximum speed of fast forwarding and rewinding.
0: 16 times normal speed
1: 32 times normal speed
2: 50 times normal speed 101 SHTL MAX
0000
0001
0002x8.4
x16x32This selects the maximum speed in the shuttle mode.
0: 84 times normal speed
1: 16 times normal speed
2: 32 times normal speed
107 PLAY DELAY 0000
0005
00150 (VTR1)
5 (VTR2) 
15This selects the PLAY mode startup time in frame increments.

When VTR1 and VTR2 are connected to external components
and controlled from them, set the same PLAY DELAY value for
the whole system.
[[
109 AUTO REW
0000
0001OFFONThis selects the processing to be conducted when the tape end
has been detected.
0: The tape is stopped when it comes to the end.
1: The tape is rewound to its start.[[ 103 AUDIO MUTE
0000
0001OFFONThis selects the status to be established until the audio signals are
output when the unit has transferred from the STOP mode or
search mode to the PLAY mode.
0: The time taken until the audio signals are output is reduced.
1: The audio signals are output after the mode transfer has been
completed.[[
106 EE MODE SEL
0000
0001NORMALTHRUThis selects the output signals in the E-E mode.
0: The signals, which have been delayed by the time taken to
process them internally, are output.
1: The signals are not internally processed and output in their
original form without a delay.

O“0: NORMAL” is forcibly selected when assemble or insert
editing mode has been selected even with internal connections
(INT mode) or even in the EXT/SEPARATE mode.
OThe “THRU” mode is always set for VTR1.[ [
[[
108 CAP. LOCK
0000
0001
4F
8F
This selects the CAPSTAN LOCK mode when the SYNCHRO
switch has been set to CF.
0: 4F mode
1: 8F mode

In the 525i mode, this setup menu item does not appear.[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
33
Setup menus
OPERATION menu 
						

							OPERATION menu
The underlining indicates the factory setting.170 HUMID OPE
0000
0001OFFONThis selects whether the unit is to continue operating when
condensation has formed.
0: The unit does not operate.
1: It operates even when condensation has formed but no
guarantees are made for its operation.

Since tape damage or other problems may occur when “1: ON”
has been selected, the “0: OFF” setting should normally be used.
171 ALL STOP SEL
0000
0001STOPSTILLThis selects the unit’s mode to be established when the ALL
STOP button has been pressed.
0: The unit is set to the STOP mode.
1: The unit is set to the still-picture (SHTL + 0.0, JOG STILL)
mode.[ [
110 MEMORY STOP
0000
0001OFFONThis selects the processing to be conducted when the counter
displays zeros in the CTL mode or during FF or REW.
0: The VTR is not shut down.
1: The VTR is automatically shut down.

OFor the stop mode, either the stop or still-picture (SHTL + 0.0,
JOG STILL) mode is set depending on the setup menu item
No.315 (AFTER CUE-UP) setting.
OWhen both the AUTO REW function and MEMORY function
have been selected, the AUTO REW function takes priority.[[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
172 VTR1 IN SEL
0000
0001V1 INV2 INThis selects the VIDEO/AUDIO input of VTR1 when the analog
signal input has been selected.
0: VTR1 IN serves as the VTR1 input.
1: VIDEO IN and AUDIO IN of VTR2 serve as the VTR1 input.

OThe unit will not operate when SDI signal input has been
selected.
OThis operation is not performed in the 625i mode.[
173 BATTERY SEL
0000
0001
0002
0003
0004
0005
0006
0007
000810.8V11.0V
11.2V
11.4V
11.6V
11.8V
12.0V
12.5V
13.0VThis selects the voltage threshold for warning when the DC supply
voltage has dropped.
(The unit’s power is automatically turned off when it drops to 10.6
V.)
0: When it has dropped to 10.8 V
1: When it has dropped to 11.0 V
2: When it has dropped to 11.2 V
3: When it has dropped to 11.4 V
4: When it has dropped to 11.6 V
5: When it has dropped to 11.8 V
6: When it has dropped to 12.0 V
7: When it has dropped to 12.5 V
8: When it has dropped to 13.0 V[
174 SDI OUT
0000
0001
VTR1
VTR2This selects the SDI output.
0: The VTR1’s signals are output.
1: The VTR2’s signals are output.[
34
Setup menus 
						

							270
The underlining indicates the factory setting.202 ID SEL
0000
0001OTHERDVCPROThis selects the ID information to be returned to the controller.
0: 20 25H (525i mode) is returned.
1: The DVCPRO’s own ID and F0 33H (525i mode) is returned.

This operation is not performed in the 625i mode.
207 STOP BIT
0000
000112This selects the RS-232C (EDL) stop bit.
0: 1 bit
1: 2 bits[ 205 BAUD RATE 0000
0001
0002
0003
00041200
2400
4800
960019200This selects the RS-232C (EDL) transfer (baud) rate.
[ [[
208 PARITY
0000
0001
0002NON
ODDEVENThis selects the RS-232C (EDL) parity.
0: Parity bit is not used.
1: Parity bit is used with odd parity.
2: Parity bit is used with even parity.[
FLOW CONTROL
0000
0001NONERTSCTSThis selects the RS-232C (EDL) communication flow control.
0: No flow control using RTS/CTS.
1: Flow control using RTS/CTS.[
271 EDL FORMAT
0000
0001AGA850CMX340This selects the format in which the EDL is to be dumped.
0: Format which is common with Panasonic’s AG-A850.
1: Format which is common with the CMX340 editing system.[ 206 DATA LENGTH
0000
0001
7
8This selects the RS-232C (EDL) data length.
0: 7 bits
1: 8 bits[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
35
Setup menus
INTERFACE menu 
						

							The underlining indicates the factory setting.[[ 303 STD/NON-STD
0000
0001
0002AUTOSTD
N-STDThis selects the STD or NON-STD to match the composite input
signals.
0: The standard/non-standard signals are automatically identified
and processed.
1: The standard signals are processed.  (Forced STD)
2: The non-standard signals are processed.  (Forced NON-STD)

This operation is not performed in the 625i mode.
304 SERVO REF
0000
0001AUTOEXTThis selects the servo synchronizing signals.
0: During recording or editing, the servo is synchronized with the
input signals; during playback, it is synchronized with the REF
signal.
1: The servo is synchronized with the REF signal at all times.
307 EDIT RPLCE3
0000
0001
0002
0003
0000
0001
0002
0003N-DEF
CH1
CH2
CH1+2As with setup menu item No.305, this selects the VTR’s channel 3
editing commands ON or OFF in accordance with the analog
audio signals specified by the controller.
0: No setting
1: Setting accords with the analog channel 1 editing commands.
2: Setting accords with the analog channel 2 editing commands.
3: Setting accords with the analog channel 1 or channel 2 editing
commands.

This operation is not performed in the 625i mode.[ 305 EDIT RPLCE1
0000
0001
0002
0003N-DEF
CH1CH2
CH1+2This selects the allocation of the channels using the controller’s
analog audio editing commands when a controller without
functions for digital audio editing is used to edit the digital audio
signals of the VTR.
The VTR’s channel 1 editing commands can be set ON or OFF in
accordance with the analog audio signals specified by the
controller.
0: No setting
1: Setting accords with the analog channel 1 editing commands.
2: Setting accords with the analog channel 2 editing commands.
3: Setting accords with the analog channel 1 or channel 2 editing
commands.

This operation is not performed in the 625i mode.[ [[
306 EDIT RPLCE2
0000
0001
0002
0003N-DEF
CH1
CH2CH1+2As with setup menu item No.305, this selects the VTR’s channel 2
editing commands ON or OFF in accordance with the analog
audio signals specified by the controller.
0: No setting
1: Setting accords with the analog channel 1 editing commands.
2: Setting accords with the analog channel 2 editing commands.
3: Setting accords with the analog channel 1 or channel 2 editing
commands.

This operation is not performed in the 625i mode.[
308 EDIT RPLCE4
N-DEF
CH1
CH2
CH1+2As with setup menu item No.305, this selects the VTR’s channel 4
editing commands ON or OFF in accordance with the analog
audio signals specified by the controller.
0: No setting
1: Setting accords with the analog channel 1 editing commands.
2: Setting accords with the analog channel 2 editing commands.
3: Setting accords with the analog channel 1 or channel 2 editing
commands.

This operation is not performed in the 625i mode.[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
36
Setup menus
EDIT menu 
						

							The underlining indicates the factory setting.[ 311 AUD EDIT IN
0000
0001
CUT
FADEThis selects how to join audio edit IN points.
0: Cut editing
1: Fade editing
313 AUTO ENTRY
0000
0001
0002
0003OFFREC1
REC2
ALLThis selects whether a previous edit OUT point is to be registered
automatically in the setting as the next edit IN point after
automatic editing.
0: No automatic setting
1: Automatic setting for VTR2 only
2: Automatic setting for VTR2 only (with compensation of –12
frames)
3: Automatic setting for VTR1 and VTR2 312 AUD EDIT OUT
0000
0001
CUT
FADEThis selects how to join audio edit OUT points.
0: Cut editing
1: Fade editing
315 AFTER CUE-UP
0000
0001STOPSTILLThis selects the unit’s mode to be established upon completion of
the cue-up operation.
0: The unit is set to the stop mode.
1: The unit is set to the still-picture (SHTL + 0.0, JOG STILL)
mode.[
318 AUD MEM CH
0000
0001
0002
0003CH1
CH2CH3
CH4This selects the channel for which the voice-over editing or audio
cross-channel editing is to be performed.
0: Editing in channel 1
1: Editing in channel 2
2: Editing in channel 3
3: Editing in channel 4[ [
[
317 AUD MEM MODE
0000
0001
0002OFFINT_X
INT_VOThis selects whether voice-over editing or audio cross-channel
editing is to be performed using the internal audio memory.
0: No voice-over editing or audio cross-channel editing is
performed.
1: Audio cross-channel editing is performed.
2: Voice-over editing is performed.[
325 POSTROLL TM 0000
0001
0002
00030.5s
1s2s
3sThis selects the postroll time (in 1-second increments).
[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
37
Setup menus
EDIT menu 
						

							The underlining indicates the factory setting.370 BEEP
0000
0001
0002
0003OFF
ENTRY
ALL1ALL2This selects whether the confirmation tone is to be sounded.
0: The confirmation tone does not sound.
1: The confirmation tone is sounded when registering is performed
or when an error or warning has occurred.
2: The confirmation tone is sounded when registering is
performed, when an edit IN or OUT point is passed or when an
error or warning has occurred.
3: The confirmation tone is sounded when registering is
performed, when an edit OUT point is passed or when an error
or warning has occurred.  It does not sound when an edit IN
point is passed.
374 EDL AUTO CLR
0000
0001OFFONThis selects whether to clear the first event and overwrite the
subsequent events successively when the EDL is full with
registered events.
0: Events cannot be overwritten.
1: Events can be overwritten. 371 SV-UNLK EDIT
0000
0001
0002EDIT
ABORT1ABORT2This selects in what editing mode the editing is to be suspended
when servo lock is not engaged.
0: Editing is not suspended and is continued.
1: Editing is suspended when the servo lock is not engaged in the
editing run-up period.
2: Editing is suspended when the servo lock is not engaged in the
editing run-up period or after edit recording mode has been
suddenly established.
372 SYNCHRO EDIT
0000
0001
OFF
ON
This selects whether editing is to be suspended if phase
synchronization cannot be achieved at an accuracy of ±0 frame
when the SYNCHRO setting is ON.
0: Editing is not suspended.
1: Editing is suspended.
373 SYNCHRO
0000
0001VTR1VTR2This sets the VTR for which the phase is synchronized.
0: Phase is synchronized for VTR1.
1: Phase is synchronized for VTR2.
375 SPLIT EDIT
0000
0001AUDIOVIDEOThis selects the split editing reference.
0: The video edit points are used as the reference for audio split
editing.
1: The audio edit points are used as the reference for video split
editing.[ [
[ [
[
377 1ST EDIT TC This selects the time code preset value during 1ST EDIT.
00:00:00:00 to 23:59:59:29 (525i mode)
00:00:00:00 to 23:59:59:24 (625i mode)[
378 1ST EDIT UB This selects the user’s bit preset value during 1ST EDIT.
00:00:00:00 to FF:FF:FF:FF[ [
376 1ST EDIT DUR
0000
000126sT-ENDThis selects the time during which the black burst signal is to be
recorded during 1ST EDIT.
0: The signal is recorded for 26 seconds, after which the tape is
reversed for 3 seconds and stopped.  The point at which the
tape has stopped serves as the point which is set by 1ST EDIT
PRESET.
1: The signal is recorded to the tape end or the position where the
tape is stopped by ALL STOP.  When it is recorded to the tape
end, the tape is automatically reversed to the 1ST EDIT
PRESET position.[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
38
Setup menus
EDIT menu 
						

							The underlining indicates the factory setting.379 1ST-E TITLE
This selects the title screen characters (3 lines a
20 characters)
which is to be superimposed onto the black burst signal during
1ST EDIT.
Characters:
ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789
,.:;?!/
’()+–±¢
=

OThis item takes effect when ON has been selected as the setup
menu item No.380 (1ST E-DISP) setting.
OThis operation is not performed in the 625i mode.
380 1ST-E DISP
0000
0001OFFONThis sets whether the title screen is to be superimposed onto the
black burst signal and recorded during 1ST EDIT.
0: The title screen is not superimposed.
1: The title screen is superimposed.

The screen cannot be superimposed in the 625i mode.[
382 SKIP (r) MARK
0000
0001OFFONThis selects the processing of already edited events when multi-
event editing is to be performed.
0: Already edited events are re-edited during multi-event editing.
1: Multi-event editing is performed with the already edited events
skipped.[ 381 ENTRY CORR
0000
0001OFFONThis selects whether to provide compensation for the OUT point
registration when previewing open-ended editing.
0: No compensation is provided.
1: Compensation is provided (–12 frames).[ [ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
39
Setup menus
EDIT menu 
						

							The underlining indicates the factory setting.400 STILL TIMER 0000
0001
0002
0003
0004
0005
0006
0007
0008
0.5s
5s
10s
20s
30s
40s
50s
1min
2minThis selects the time taken for the unit to be set to the tape
protection mode when it has been left standing in the STOP or
search STILL (JOG, VAR or SHTL) mode.
(Units: s = second, min = minute)
403 STOP PROTECT
0000
0001
STEP
HALF
This selects the tape protection mode operation when the unit has
been left standing in the STOP mode.
0: Step FWD 
1: Half loading

When step FWD has been set, the unit is automatically transferred
to the half loading mode when it has been left standing for a total
of 30 minutes in the STOP mode. 401 SRC PROTECT
0000
0001STEPHALFThis selects the tape protection mode operation when the unit has
been left standing in the STILL mode.
0: Step (or step FWD in STILL mode).
1: Half loading

When step FWD has been set, the unit is automatically transferred
to the half loading mode when it has been left standing for a total
of 30 minutes in the STILL mode.
402 DRUM STDBY
0000
0001
OFF
ONThis selects the drum operation in the standby OFF mode.
0: The drum is stopped.
1: The drum is rotated.
[[ [[ [[
[[ Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
V
T
R
1V
T
R
2
40
Setup menus
TAPE PROTECT menu