Panasonic Aj Lt95 Operating Instructions Manual
Have a look at the manual Panasonic Aj Lt95 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11 Counter display area E Event number display lamps This unit controls up to 200 sets of edit data (001 to 200) in the form of 3-digit event numbers. One of the following displays appears depending on the editing status. n###:Indicates that the No.### event is a new event which has not been stored on the EDL (edit list). (New event) d###:Indicates that the No.### event is an event which has been deleted from the EDL. ###:Indicates that the No.### event has been stored on the EDL. FULL:Indicates that all 200 events have now been stored. ----:Indicates that the remote switch or the OPERATION MODE switch has been set to SEPARATE. r S t:Appears when the unit has been reset after the power was turned on. r###:Indicates that the No.### event is an event that has been edited. F Edit point setting display lamps (IN/OUT lamps) The lamp corresponding to the type of edit point which has been set lights. G Split editing display lamps (A SP, V SP lamps) These light when split editing has been set. Set the setup menu No. 375 (SPLIT EDIT) setting to AUDIO and register a split edit point. The A SP lamp lights to indicate that the audio spit edit mode has been established. Similarly, set it to VIDEO and register a split editing point and the V SP lamp lights to indicate that the video split mode has been established.H Split edit point setting display lamps These are positioned at the side of the IN lamps, and they light up for the VTR which is used to set the split edit point. Parts and their functions AV SPIN OUT IN OUTF E F H G
12 Panel switch area 1 CONTROL switch REMOTE:For controlling the unit from the REMOTE connector (9P). LOCAL:For controlling the unit using the controls on its front panel. EXT VTR:For controlling an external VTR using the controls on the unit’s front panel. The VTR connected to the 9P connector of VTR1 can be controlled using the control system of VTR1. This switch is forcibly set to the LOCAL position in the 625i mode. 2 PREROLL switch Used to set the preroll time to 3, 5 or 7 seconds. When the phase synchronization does not serve the purpose or editing has failed or for other reasons, the preroll time is automatically set to the next longest setting. (If 7 seconds is set, this will remain set as the preroll time.) 3 SYNCHRO switch Used to set the phase synchronization and/or color framing. CF:Phase synchronization and color framing are performed. ON:Phase synchronization is performed but color framing is not performed. OFF:Phase synchronization is not performed. 4 TAPE/EE switch Used to select the signals which are output in the stop, fast forward or rewind mode. TAPE:The signals played back from the tape are output. EE:The input-switched input signals are output.5 TC switch REGEN:The built-in time code generator is synchronized to the time code selected by the setup menu item No.570 (REGEN SEL) setting. R-RUN:The time code advances only during recording. (Presettable) F-RUN:The time code advances regardless of the operation mode while the power remains on. (Presettable) 6 REC INHIBIT switch Used to select whether signals are to be recorded on the cassette tape. ON:Recording on the cassette tape is inhibited. At this time, the REC INH lamp in the display tube lights. OFF:Recording on the tape is possible provided that the accidental erasure prevention mechanism on the cassette tape is at the recording enable position. Parts and their functions CONTROLREMOTELOCALEXT VTR PREROLL SYNCHRO7 5 3CFONOFF REGEN R-RUN F-RUN MODEREC INHIBITTCVTR 1 TAPE EEON OFFREGEN R-RUN F-RUN MODEREC INHIBITTCVTR 2 TAPE EEON OFF ANALOGOPERATIONMODEEDITV2VIDEO INSDI ANALOGSEPARATE EXT AUDIO IN V1-V2 V1 V2OUT2 CH4 CH2 CH4 CHINT 456456321
13 Panel switch area 7 ANALOG AUDIO IN switch Used to set the allocation of the audio signals to the 4 analog audio input connectors (on the rear panel). V1-V2 (2ch):Of the 4 inputs, the two on the VTR1 side are supplied to the VTR1’s input connectors, and the two on the VTR2 side are supplied to the VTR2’s input connectors. V1 (4ch):The 4 inputs are allocated to the 4 channels of VTR1. V2 (4ch):The 4 inputs are allocated to the 4 channels of VTR2. 8 ANALOG AUDIO OUT switch Used to set the allocation of the audio signals to the 4 analog audio output connectors (on the rear panel). V1-V2 (2ch):Of the 4 outputs, two on the VTR1 side are supplied to the VTR1’s output connectors, and two on the VTR2 side are supplied to the VTR2’s output connectors. V1 (4ch):The 4 outputs are allocated to the 4 channels of VTR1. V2 (4ch):The 4 outputs are allocated to the 4 channels of VTR2.9 OPERATION MODE switch INT:In this mode, editing from VTR1 to VTR2 is accomplished using the internal connections. VTR1 recording is prohibited. EXT:In this mode, editing from VTR1 to VTR2 is accomplished using the external analog connections. VTR1 recording is prohibited. SEPARATE: In this mode, VTR1 and VTR2 are operated independently. : V2 VIDEO input selector switch Used to select the video input of VTR2 when the OPERATION MODE switch is at the EXT or SEPARATE position. SDI:Serial digital video signals are input. ANALOG:Analog video signals are input. Parts and their functions CONTROLREMOTELOCALEXT VTR PREROLL SYNCHRO7 5 3CFONOFF REGEN R-RUN F-RUN MODEREC INHIBITTCVTR 1 TAPE EEON OFFREGEN R-RUN F-RUN MODEREC INHIBITTCVTR 2 TAPE EEON OFF ANALOGOPERATIONMODEEDITV2VIDEO INSDI ANALOGSEPARATE EXT AUDIO IN V1-V2 V1 V2OUT2 CH4 CH2 CH4 CHINT 789:
14 AUDIO control area 1 POWER switch Used to control the unit’s power. 2 AUDIO MONITOR SELECT switches Used to select the audio monitor output and speaker output. OV1/V1•2/V2 switch V1:The VTR1 sound is output to the left and right channels. V1•2:The VTR1 sound is output to the left channel and the VTR2 sound to the right channel. V2:The VTR2 sound is output to the left and right channels. OL (V1) switch, R (V2) switch The selected audio channel sound is output to the left (or right) channel. When mixing between 1 and 2, the mixed signals of channel 1 and channel 2 are output; when mixing between 3 and 4, the mixed signals of channel 3 and channel 4 are output.3 Analog audio recording level controls and UNI/VAR switch For each analog audio input connector (XLR) on the rear panel there is one level control. When the UNI/VAR switch is set to VAR, the audio recording level can be adjusted separately for each input channel. When it is set to UNI, the levels are fixed to the initial values regardless of the positions of the level controls. When V2 IN is selected as the setup menu item No.172 (VTR1 IN SEL) setting and the same sound is to be recorded on VTR1 and VTR2, the recording level for both VTR1 and VTR2 is adjusted using these controls. (The recording level cannot be adjusted separately for VTR1 and VTR2.) Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3 A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC 12 3
15 AUDIO control area 4 V1 audio playback level controls/V2 INT audio recording level controls These controls enable the playback audio level of VTR1 to be adjusted for each channel. They are also used to adjust the volume during editing from VTR1 to VTR2. Slide controls are used to make for fine and smooth adjustments. The position marked “0” denotes the reference level. (–20 dB for 525i mode; –18 dB for 625i mode)5 V2 AUDIO input selector switches Used to select the sound which is to be input to the audio channels of VTR2. OINT/SDI/ANALOG switch INT:The VTR1 audio signals are input to VTR2 by the internal digital connections. Their level can be adjusted by the level controls 4 . SDI:The SDI embedded audio signals, which have been input to the SDI connector, are supplied to VTR2. Their level can be adjusted by the level controls 6 . ANALOG: The analog signals which have been input are supplied to VTR2. Their level can be adjusted by the level controls 3 . OChannel selector switches The audio signals selected by the INT/SDI/ANALOG switch are input to the VTR2 channels which are selected by these switches. When mixing between 1 and 2, the mixed signals of channel 1 and channel 2 are input; when mixing between 3 and 4, the mixed signals of channel 3 and channel 4 are input. Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC 4 5
16 AUDIO control area 6 SDI audio recording level controls and UNI/VAR switch For each channel of the superimposed sound which is input from the SDI input connector (on the rear panel) there is one level control. When the UNI/VAR switch is set to VAR, the audio recording level can be adjusted separately for each input channel. When it is set to UNI, the levels are fixed to the initial value regardless of the positions of the level controls. 7 V2 audio playback level controls These controls enable the playback audio level of VTR2 to be adjusted for each channel. Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3 A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC 7 6
17 Editing operation area 1 VTR1 selector button Press this button to perform VTR1 editing-related settings or operations. Check that its LED has lighted before proceeding with the VTR1 editing-related settings or operations. 2 VTR2 selector button Press this button to perform VTR2 editing-related settings or operations. Check that its LED has lighted before proceeding with the VTR2 editing-related settings or operations. The VTR1 and VTR2 simultaneous operation mode is established by pressing ([SHIFT] + [VTR1]) or ([SHIFT] + [VTR2]) together, and both LEDs 1 and 2 light. To release the simultaneous operation mode, press the VTR1 or VTR2 button. In the simultaneous operation mode, it is not possible for editing settings and menu settings to be performed at the same time. 3 REC button To set the unit to the recording mode manually, press this button together with the PLAY button. Recording on VTR1 is possible only when the OPERATION MODE switch has been set to SEPARATE. When the button is pressed while the REC INHIBIT switch is at OFF, the E-E mode will be established for the video/audio channel 1 to channel 4 signals for as long as the button is held down.4 PLAY (STOP) button PLAY:Press this button to set the VTR to the playback mode. STOP ([SHIFT] + [PLAY]): To set the VTR to the STOP mode, press the PLAY button while holding down the SHIFT button. 5 STILL (STBY OFF) button STILL:Press this button to set the unit to the still- picture mode. STBY OFF ([SHIFT] + [STILL]): To release the standby mode while the still- picture or stop mode is established, press the STILL button while holding down the SHIFT button. 6 REW button Press this button to rewind the tape. 7 FF button Press this button to fast forward the tape. Tape travel stops when the REW and FF buttons are pressed at the same time. Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC 145632 7
18 Editing operation area 8 Search dial This is used to control the tape travel. It is also used when edit points are to be located or when playing back tapes. The shuttle mode is established when the dial is “out” (up), and the jog mode is established when it is pushed in. Each time the dial is pressed, the unit alternates between these two modes. 9 ASMBL (1ST EDIT) button ASMBL: Press this button to initiate assemble editing. Check that its LED has lighted before proceeding with editing. 1ST EDIT ([SHIFT] + [ASMBL]): The editing tape must have black burst signals, time codes or CTL signals recorded on it ahead of time. To initiate first editing, press the ASMBL button while holding down the SHIFT button. For further details, refer to page 53 (“Preparing tapes for editing”).: V button Press this button to initiate video insert editing. Check that its LED has lighted before proceeding with editing. ; A1 (A3) button A1:Press this button to initiate audio channel 1 insert editing. Check that its LED has lighted before proceeding with editing. A3 ([SHIFT] + [A1]): To initiate audio channel 3 insert editing, press the A1 button while holding down the SHIFT button. Check that its LED has lighted before proceeding with editing. The A3 LED will light in the 25 Mbps mode also but CH3 editing operations cannot be performed. Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3 A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC 9:; 8
19 Editing operation area < A2 (A4) button A2:Press this button to initiate audio channel 2 insert editing. Check that its LED has lighted before proceeding with editing. A4 ([SHIFT] + [A2]): To initiate audio channel 4 insert editing, press the A2 button while holding down the SHIFT button. Check that its LED has lighted before proceeding with editing. The A4 LED will light in the 25 Mbps mode also but CH4 editing operations cannot be performed. = TC button Press this button to initiate time code insert editing. Check that its LED has lighted before proceeding with editing.> EDIT button When this button is pressed during VTR2 playback, the E-E mode is established in accordance with the selected edit mode (ASMBL, A1, A2, A3, A4 or TC) for as along as the button is held down. (Select E- E) When it is pressed together with the PLAY button during VTR2 playback, editing is initiated in the selected edit mode (ASMBL, A1, A2, A3, A4 or TC). (Manual editing) To exit manual editing, press the ALL STOP button. Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC
20 Editing operation area ? EVENT button EVENT: To change the event number, press this button, then use the numeric input keys to input the event number, and press the ENTER button. DELETE ([SHIFT] + [EVENT]): Press this button to delete an event which has been registered. “d” is indicated in the event number display area. @ IN (LAST X) button IN:Press this button to set or display an edit IN point. LAST X ([SHIFT] + [IN]): To re-register an event which has been deleted, press this button while holding down the SHIFT button. The “d” indication is cleared to a blank display. A OUT (LAST ED) button OUT: Press this button to set or display an edit OUT point. LAST ED ([SHIFT] + [OUT]): To return to the previously previewed data, press this button while holding down the SHIFT button.B DUR (TOTAL) button DUR: Press this button to set or display the duration. TOTAL ([SHIFT] + [DUR]): To show the total editing time on the VTR2 display, press this button while holding down the SHIFT button. C GO TO (GO TO OUT) button GO TO: To search the edit IN point on the tape with the edit IN point already set, press this button. GO TO OUT ([SHIFT] + [GO TO]): To search the edit OUT point on the tape with the edit OUT point already set, press this button while holding down the SHIFT button. Parts and their functions AUDIO MONITOR SELECT LR CH 1 4 1 3MIX ANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDIT PREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FS DISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3 A4TCREC EDIT2 4 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI 10 10 20 30 00INT INT ANALOGSDIINTANALOGSDIV2 INPUTINT 010 10 20 30 00010 10 20 30 000 CH 1POWEROFFONUNI VA RCH 2 CH 3 CH 4ANALOGV1/V2REC ?@ABC