NEC Neax 2400 Ipx Wireless System Manual
Have a look at the manual NEC Neax 2400 Ipx Wireless System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 5 NDA-24301
Pag e 2 84
Revision 1.0
APSP : Assignment of Trunk Line Appearance for DM
1. GENERAL
This command is used to assign/delete the “COT trunk seizure” data, when a PS makes a call via this trunk and
an LC (made cross connection with the COT) of the existing PBX with no wireless feature.
2. PRECAUTIONS
1. Assign the physical PS station number for the “PS STN” input data.
2. This command data must be assigned to each COT circuit, that is provided with the physical cross
connection with an LC of the “existing PBX with no wireless feature”.
3. DATA ENTRY INSTRUCTIONS
TENANT
(TN)PS STATION NUMBER
(PS STN)Route Number
(RT)
1 - 255Trunk Number
(TK)
1 - 255
PS STN
Enter the physical PS
station number.
RT
Enter the route number for
COT trunk to be provided.
TN
Enter Tenant Number.
TK
Enter the trunk number for
COT trunk to be provided.
NDA-24301 CHAPTER 5 Page 285 Revision 1.0 4. DATA SHEET COT Trunk Seizure Data Assignment Sheet TENANT (TN)PS STATION NUMBER (PS STN)ROUTE NUMBER (RT) 1 - 255TRUNK NUMBER (TK) 1 - 255
CHAPTER 5 NDA-24301 Pag e 2 86 Revision 1.0 AZDL : ZT Program Download 1. GENERAL This command is used to download ZT program from “Program Master ZT” to “Program Download ZT”. 2. PRECAUTIONS 1. This feature is available for Series 7300 or later software. 2. For detailed information on ZT program Download service. 3. DATA ENTRY INSTRUCTIONS PROGRAM MASTER ZT PCN : PHS Community Number of rogram Master ZT: 1-1024 PROGRAM MASTER ZT CRN : Calling Area Number of Program Master ZT: 1-32 PROGRAM MASTER ZT GRN : Group Number of Program Master ZT: 1-8 PROGRAM MASTER ZT CSN/ZTN : ZT Number of Program Master ZT: 1-32 PROGRAM DOWNLOAD ZT PCN : PHS Community Number of Slave Program Download ZT: 1-1024 PROGRAM DOWNLOAD ZT CRN : Calling Area Number of Slave Program Download ZT: 1-32 PROGRAM DOWNLOAD ZT GRN : Group Number of Slave Program Download ZT: 1-8 PROGRAM DOWNLOAD ZT CSN/ZTN: ZT Number of Slave Program Download ZT: 1-32
NDA-24301 CHAPTER 5 Page 287 Revision 1.0 4. DATA SHEET ZT Program Download Data Sheet PROGRAM MASTER ZT PCN 1-1024PROGRAM MASTER ZT CRN 1-32PROGRAM MASTER ZT GRN 1-8PROGRAM MASTER ZT CSN/ZTN 1-32PROGRAM DOWNLOAD ZT PCN 1-1024PROGRAM DOWNLOAD ZT CRN 1-32PROGRAM DOWNLOAD ZT GRN 1-8PROGRAM DOWNLOAD ZT CSN/ZTN 1-32
CHAPTER 5 NDA-24301 Pag e 2 88 Revision 1.0 AHLG : Assignment of CFT Hot Line Group 1. GENERAL This command is used to assign, delete and display the DM data which is concerned with PCS Calling Conference Group. List Up Command: LHLG 2. PRECAUTIONS 1. This command is available for Series 7400 or later software. 2. “Set” key and “Del” key can be used after TN and ACC are entered and then this data is read by pressing “Get” key. If this data is not programmed, press “Get” key again, PORT, TYPE, D_TN, D_STN and D_ADC can be assigned. 3. The input parameter depends on TYPE value. TYPE=0 or blank : Not displayed TYPE=1 : D_TN, D_STN TYPE=2 : D_ADC 4. Only Speed Calling Dial Number which is the same tenant as conference leader port can be entered. 5. The user must assign the data to all ports (PORT 0-7). 6. If all ports are TYPE=0, this assignment ends in failure. 7. Data writing is executed by pressing “Set” key. 3. DATA ENTRY INSTRUCTIONS TN (TENANT NUMBER) : 1- ACC (CFTB H/L ACCESS CODE) : 0-9, #, * (maximum 5 digits) PORT (PORT NUMBER) : 1-7 TYPE (KIND OF STN) : 0=Vacant Port 1=STN/PS 2=OUTSIDE TRUNK D_TN (TENANT NUMBER OF DESTINATION) : 1- D_STN (STATION NUMBER OF DESTINATION) : 0-9, #, * (maximum 5 digits) D_ADC (SPEED CALLING DIAL NUMBER OF DESTINATION): 0-9, #, * (maximum 4 digits)
NDA-24301 CHAPTER 5 Page 289 Revision 1.0 4. DATA SHEET TENANT NUMBER (TN)STATION NUMBER OF CFTB H/L ACCESS CODE (ACC) Max. 5 digits PORTKIND OF STN (TYPE) 0~2TENANT NUMBER OF DESTINATION (D_TN)STATION NUMBER OF DESTINATION (D_STN) Max. 5 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7 TENANT NUMBER (TN)STATION NUMBER OF CFTB H/L ACCESS CODE (ACC) Max. 5 digits PORTKIND OF STN (TYPE) 0~2TENANT NUMBER OF DESTINATION (D_TN)STATION NUMBER OF DESTINATION (D_STN) Max. 5 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7 TENANT NUMBER (TN)STATION NUMBER OF CFTB H/L ACCESS CODE (ACC) Max. 5 digits PORTKIND OF STN (TYPE) 0~2TENANT NUMBER OF DESTINATION (D_TN)STATION NUMBER OF DESTINATION (D_STN) Max. 5 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7
CHAPTER 5 NDA-24301 Pag e 2 90 Revision 1.0 AHLGL : Assignment of CFT Hot Line Group for LDM 1. GENERAL This command is used to assign, delete and display the LDM data which is concerned with PCS Calling Conference Group. List Up Command: LHLGL 2. PRECAUTIONS 1. This command is available for Series 7400 or later software. 2. This command is used for the Local Node (LN). 3. “Set” key and “Del” key can be used after UGN and TELN are entered and then this data is read by pressing “Get key”. If this data is not programmed, press “Get” key again, DA, PORT, TYPE, D_UGN, D_TELN and D_ADC can be assigned. 4. The input parameter depends on TYPE value. TYPE=0 or blank : Not displayed TYPE=1 : D_UGN, D_TELN TYPE=2 : D_ADC 5. Only Speed Calling Dial Number which is the same tenant as conference leader port can be entered. 6. The user must assign the data to all ports (PORT 0-7). 7. If all ports are TYPE=0, this assignment ends in failure. 8. Data writing to LDM is executed by pressing “Set” key. 3. DATA ENTRY INSTRUCTIONS UGN (USER GROUP NUMBER) TELN (CFTB H/L ACCESS CODE : 0-9, #, * (maximum 16 digits) [TELEPHONE NUMBER]) DA : 0=Stop : 1=Continue alerting, when the STN does not answer. PORT (PORT NUMBER) : 1-7 TYPE (KIND OF STN) : 0=Vacant Port 1=STN/PS 2=OUTSIDE TRUNK (Not used) D_UGN (USER GROUP NUMBER OF DESTINATION) D_TELN (TELEPHONE NUMBER OF DESTINATION) : 0-9, #, * (maximum 16 digits) D_ADC (SPEED CALLING DIAL NUMBER OF DESTINATION): 0-9, #, * (maximum 4 digits) (Not used)
NDA-24301 CHAPTER 5 Page 291 Revision 1.0 4. DATA SHEET USER GROUP NUMBER (UGN)TELEPHONE NUMBER OF CFTB H/L ACCESS CODE (TELN) Max. 16 digitsRINGING STOP AFTER NO ANSWER TIMER (DA) 0/1 PORTKIND OF STN (TYPE) 0~2USER GROUP NUMBER OF DESTINATION (D_UGN)TELEPHONE NUMBER OF DESTINATION (D_TELN) Max. 16 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7 USER GROUP NUMBER (UGN)TELEPHONE NUMBER OF CFTB H/L ACCESS CODE (TELN) Max. 16 digitsRINGING STOP AFTER NO ANSWER TIMER (DA) 0/1 PORTKIND OF STN (TYPE) 0~2USER GROUP NUMBER OF DESTINATION (D_UGN)TELEPHONE NUMBER OF DESTINATION (D_TELN) Max. 16 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7 USER GROUP NUMBER (UGN)TELEPHONE NUMBER OF CFTB H/L ACCESS CODE (TELN) Max. 16 digitsRINGING STOP AFTER NO ANSWER TIMER (DA) 0/1 PORTKIND OF STN (TYPE) 0~2USER GROUP NUMBER OF DESTINATION (D_UGN)TELEPHONE NUMBER OF DESTINATION (D_TELN) Max. 16 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7
CHAPTER 5 NDA-24301 Pag e 2 92 Revision 1.0 AHLGN : Assignment of CFT Hot Line Group for NDM 1. GENERAL This command is used to assign, delete and display the NDM data which is concerned with PCS Calling Conference Group. List Up Command: LHLGL 2. PRECAUTIONS 1. This command is available for Series 7400 or later software. 2. This command is used for the Network Control Node (NCN). 3. “Set” key and “Del” key can be used after UGN and TELN are entered and then this data is read by pressing “Get key”. If this data is not programmed, press “Get” key again, DA, PORT, TYPE, D_UGN, D_TELN and D_ADC can be assigned. 4. The input parameter depends on TYPE value. TYPE=0 or blank : Not displayed TYPE=1 : UGN, TELN TYPE=2 : ADC (Only Speed Calling Dial Number of a node assigned conference leader port can be entered.) 5. Only Speed Calling Dial Number which is the same tenant as conference leader port can entered. 6. The user must assign the data to all ports (PORT 0-7). 7. If all ports are TYPE=0, this assignment ends in failure. 8. Data writing for NDM is executed by pressing “Set” key. 3. DATA ENTRY INSTRUCTIONS UGN (USER GROUP NUMBER) TELN (CFTB H/L ACCESS CODE : 0-9, #, * (maximum 16 digits) [TELEPHONE NUMBER]) DA : 0=Stop 1=Continue alerting, when the STN does not answer. PORT (PORT NUMBER) : 1-7 TYPE (KIND OF STN) 0=Vacant Port 1=STN/PS 2=OUTSIDE TRUNK (Not used) D_UGN (USER GROUP NUMBER OF DESTINATION) D_TELN (TELEPHONE NUMBER OF DESTINATION) : 0-9, #, * (maximum 16 digits) D_ADC (SPEED CALLING DIAL NUMBER OF DESTINATION) : 0-9, #, * (maximum 4 digits) (Not used)
NDA-24301 CHAPTER 5 Page 293 Revision 1.0 4. DATA SHEET USER GROUP NUMBER (UGN)TELEPHONE NUMBER OF CFTB H/L ACCESS CODE (TELN) Max. 16 digitsRINGING STOP AFTER NO ANSWER TIMER (DA) 0/1 PORTKIND OF STN (TYPE) 0~2USER GROUP NUMBER OF DESTINATION (D_UGN)TELEPHONE NUMBER OF DESTINATION (D_TELN) Max. 16 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7 USER GROUP NUMBER (UGN)TELEPHONE NUMBER OF CFTB H/L ACCESS CODE (TELN) Max. 16 digitsRINGING STOP AFTER NO ANSWER TIMER (DA) 0/1 PORTKIND OF STN (TYPE) 0~2USER GROUP NUMBER OF DESTINATION (D_UGN)TELEPHONE NUMBER OF DESTINATION (D_TELN) Max. 16 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7 USER GROUP NUMBER (UGN)TELEPHONE NUMBER OF CFTB H/L ACCESS CODE (TELN) Max. 16 digitsRINGING STOP AFTER NO ANSWER TIMER (DA) 0/1 PORTKIND OF STN (TYPE) 0~2USER GROUP NUMBER OF DESTINATION (D_UGN)TELEPHONE NUMBER OF DESTINATION (D_TELN) Max. 16 digitsSPEED CALLING DIAL NUMBER (D_ADC) Max. 4 digits 1 2 3 4 5 6 7