NEC Neax 2400 Ipx Wireless System Manual

							CHAPTER 4 NDA-24301
Pag e 1 14
Revision 1.0
OFFICE DATA ASSIGNMENT
5) ARRC (Alternative Route Restriction Pattern Data)
Allow the restriction between the external trunk and the announcement trunk.
ICRT : Incoming Route Number
OGRT : Outgoing Route Number (Announcement trunk)
ARI-D_RES = 1 (Tandem Connection without an operator/station assistance is allowed)
6) AAED (Announcement Equipment Data)
Assign EQP=60 for the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE
TN : Tenant Number
EQP = 60 (AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE)
C : Duration of Connection
R : Sending RBT
A : 1 (Answer Signal Sending)
M : 1 (Multiple Connection)
 END
A 
						

							NDA-24301 CHAPTER 4
Page 115
Revision 1.0
OFFICE DATA ASSIGNMENT
4-2 C.F.-PS Incoming Incomplete
 Entry Procedures
1) ASYD (Assignment for System Data)
Assign whether to use a same access code for Call Forwarding-Busy Line, Call Forwarding-Don’t 
Answer and C.F.-PS Incoming Incomplete, or use separate access codes.
SYS1, INDEX5, bit 0
0=Same
1=Separate
2) ANPD (Numbering Plan Data)
Assign the necessary number of digits needed to determine the service which is required according 
to the first digit received.
3) ASPA (Special Access Code Data)
Assign the Special Access Code for the C.F.-PS INCOMING INCOMPLETE
CI=N SRV=SSCA SIDA=101 (C.F.-PS INCOMING INCOMPLETE: Set)
CI=N SRV=SSCA SIDA=102 (C.F.-PS INCOMING INCOMPLETE: Cancel)
4) ASFC (Service Feature Class Data)
Allow the C.F.-PS INCOMING INCOMPLETE according to PS Service Feature Class.
SFI=147 (C.F.-INCOMING INCOMPLETE)
RES=1 (Allowed)
 END
 START 
						

							CHAPTER 4 NDA-24301
Pag e 1 16
Revision 1.0
OFFICE DATA ASSIGNMENT
AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE
1. GENERAL DESCRIPTION
When a PS user moves Out of Zone (out of the PCS service area) and the call is disconnected, the counterpart
hears the announcement stating the call was disconnected due to the the wireless user going Out of Zone.
2. OPERATING PROCEDURE
No manual operation
3. SERVICE CONDITIONS
1. This service is valid only in a two-party call.
This service cannot be used when a call is placed on hold or conference calling participated in by three-party
or more is in progress.
2.  Digital Announcement Trunk (DAT) circuit card can be used as an announcement trunk.
3. PS user encounters BT when the announcement trunk, when used as single connection (M=0 in the
command AAED) and all the trunks are used.
4. AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE is not applied when calls are
in progress via a COT line or Attendant Console. A C.O. line subscriber hears ROT and a caller via the
Attendant Console encounters BT.
5. In the Fusion Network, every node must have one or more announcement trunks. 
						

							NDA-24301 CHAPTER 4
Page 117
Revision 1.0
OFFICE DATA ASSIGNMENT
4. PROGRAMMING
 Entry Procedures
1) ARTD (Route Class Data)
Assign the Route Class Data of the announcement trunk.
RT : Route Number
OSGS (CDN: 1) = 2
ONSG (CDN: 2)= 2
TF (CDN: 5) = 1
TCL (CDN: 6) = 4
L/T (CDN: 7) = 1
ANS (CDN: 28) = 1
Assign “0” for other data.
2) ALRTN (Assignment of Logical RT in Network Data Memory)
LGRT : Logical Route Number
FPC : Fusion Point Code
RT : Route Number
Note:Not necessary in a standalone type.
3) ATRK (Trunk Data)
Assign the LENS of the announcement trunk.
RT : Route Number
TK : Trunk Number
LENS : Line Equipment Numbers
TN : Tenant Number
 START
A 
						

							CHAPTER 4 NDA-24301
Pag e 1 18
Revision 1.0
OFFICE DATA ASSIGNMENT
3) MBTK (Make Busy of Trunk)
Set the announcement trunk in a make-busy cancel state
4) ARSC (Route Restriction Class Data)
Assign the Route Restriction Class of the station which allows access to the announcement trunk.
D/N : Day/Night Mode
TN : Tenant Number
RT : Route Number
RSC : Route Restriction Class (0-15)
RRI :  Route Restriction Index (0-3)
RES = 1 (Allowed)
5) ARRC (Alternative Route Restriction Pattern Data)
Allow the connection between an external trunk and the announcement trunk.
ICRT : Incoming Route Number
OGRT: Outgoing Route Number (Announcement trunk)
ARI-D_RES = 1 (Tandem Connection without an operator/station assistance is allowed)
6) AAED (Announcement Equipment Data)
Assign EQP=61 for AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE. 
TN : Tenant Number
 EQP = 61 (AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE)
 C : Duration of Connection
 R : Sending RBT
 A : 1 (Answer Signal Sending)
 M : 1(Multiple Connection)
 END
A 
						

							NDA-24301 CHAPTER 4
Page 119
Revision 1.0
OFFICE DATA ASSIGNMENT
NAME DISPLAY
1. GENERAL DESCRIPTION
This feature allows a PS to indicate the user information corresponding to the calling station number while
engaged in a station-to-station call.
2. OPERATING PROCEDURE
Examples of LCD display are shown below.
 When originating a station-to-station call:
LCD display of the calling station:
LCD display of the called station:
 When a station call has been transferred to another station by Call Forwarding-All Calls/Busy Line/Don’t
Answer/PS-Incoming Incomplete:
LCD display of the calling station:
LCD display of the called station:
H  .   T  A  R  O
D  I  R      S  P  D      L  N  R
M .   T  A  R  O
D  I  R      S  P  D      L  N  R
C  F  :   H  .   T  A  R  O
D  I  R      S  P  D      L  N  R
C  F  :  M .   T  A  R  O
D  I  R      S  P  D      L  N  R 
						

							CHAPTER 4 NDA-24301
Pag e 1 20
Revision 1.0
OFFICE DATA ASSIGNMENT
3. SERVICE CONDITIONS
1. This feature is available for Series 7300 or later software.
2. User information corresponding to the station number that can be displayed on the LCD is a maximum of
16 digits.
3. User information is displayed on the LCD, intended to the left. The information may consist of upper case
letters, numeric characters, and most keyboard symbols.
4. When user information is 12 digits or more, the first or last part of information can be displayed by key
operation (Refer to the User Guide of PS).
5. This service and NAME DISPLAY service by Open Application Interface (OAI) cannot be activated
concurrently.
6. This service and NAME DISPLAY service for D
terms can be activated concurrently.
7. 8-digit display or 16-digit display is selectable by System Data, but cannot be used concurrently.
8. If the PS station has no name programmed for NAME DISPLAY service, the station number is displayed in
the name field.
9. NAME DISPLAY is available for the following services:
 Station-to-station connection
 Call Forwarding-All Calls/Busy Line/Don’t Answer/PS-Incoming Incomplete
 Call Waiting
 Call Transfer
10. MEM_HDD, HDD_FDD and HDD_MAT commands can be used for saving, loading and verifying Name
Display data. For detailed information, refer to System Operation and Maintenance Manual. 
						

							NDA-24301 CHAPTER 4
Page 121
Revision 1.0
OFFICE DATA ASSIGNMENT
4. PROGRAMMING
1) ASYD (Assignment of System Data)
SYS1
SI 78
b5: 1 (Name Display In Service)
SI 79
b6: 0 (OAI In Service)
SI 241
b1: The number of digits displayed in NAME DISPLAY service
0/1: 8 digits/16 digits
2) ANDD (Assignment of Name Display Data)
Assign user’s information to Physical Station Number.
TN : Tenant Number
STN : Physical Station Number
NAME : User information (Maximum 16 digits)
 END
 START 
						

							CHAPTER 4 NDA-24301
Pag e 1 22
Revision 1.0
OFFICE DATA ASSIGNMENT
NAME DISPLAY - CCIS
1. GENERAL DESCRIPTION
In between CCIS nodes, this feature allows calling or called party information to be displayed on the LCD of a
PS.
2. OPERATING PROCEDURE
Examples of LCD display are shown below.
 When originating a call:
LCD display of the calling station:
LCD display of the called station:
 When a call has been transferred to another station by Call Forwarding-All Calls/Busy Line/Don’t Answer/
PS-Incoming Incomplete:
LCD display of the calling station:
LCD display of the called station:
H  .   T  A  R  O
D  I  R      S  P  D      L  N  R
M .   T  A  R  O
D  I  R      S  P  D      L  N  R
H  .   T  A  R  O
D  I  R      S  P  D      L  N  R
C  F  :  M .   T  A  R  O
D  I  R      S  P  D      L  N  R 
						

							NDA-24301 CHAPTER 4
Page 123
Revision 1.0
OFFICE DATA ASSIGNMENT
3. SERVICE CONDITIONS
1. This feature is available for Series 7300 or later software.
2. User information corresponding to the station number that can be displayed on the LCD is a maximum of
16 digits.
3. User information is displayed on the LCD, intended to the left. The information may consist of upper case
letters, numeric characters, and most keyboard symbols.
4. When user information is 12 digits or more, the first or last part of information can be displayed by the key
operation (Refer to the User Guide of PS).
5. This service and NAME DISPLAY service by Open Application Interface (OAI) cannot be activated
concurrently.
6. This service and NAME DISPLAY service for D
terms can be activated concurrently.
7. Either an 8-digit display or 16-digit display is selectable by System Data, but they cannot be used
concurrently.
8. If the PS station has no name programmed for NAME DISPLAY - CCIS service, “Office Code + Station
Number” is displayed in the name field.
9. NAME DISPLAY - CCIS is available for the following services:
 Tie line connection
 Call Forwarding-All Calls/Busy Line/Don’t Answer/PS-Incoming Incomplete-CCIS
 Call Waiting
 Call Transfer
10. When the parameter CI of ARTD command is set to “1” (Information transfer from ISDN line to CCIS line
is available), if Low layer compatibility and/or Calling party subaddress information elements are included
in a SETUP message from a PS, user information cannot be included in the IAI message. In this case, user
information from the PS is not displayed on the called station (PS or D
term).
11. MEM_HDD, HDD_FDD and HDD_MAT commands can be used for saving, loading and verifying Name
Display data. For detailed information, refer to System Operation and Maintenance Manual.