NEC Neax 2400 Ipx Wireless System Manual

							CHAPTER 4 NDA-24301
Pag e 1 04
Revision 1.0
OFFICE DATA ASSIGNMENT
1. ZT Initial Start-Up
1) ASYD (Assignment of System Data)
CCIS ISDN function simultaneously becomes valid when the ZT operation is attempted to be in 
service, as the ZT is regarded as a terminal of the ISDN.
SYS1
SI186 
Note 1
b6=1 (CCIS function in service)
SI220 
Note 1
b6=0 (ISDN function in service)
Note 1:ISDN and CCIS data become valid, but where the ISDN and CCIS functions are not to be
used, optional software concerning ISDN and CCIS is not necessary.
2)Call LVP Server system
3) APCNN (Assignment of PHS Community Number Data for Network Data Memory)
FUNC=1   PHS Community Number (PCN) Entry.
FPC, TN, PCN
Note:Do not assign Func=2.
4) ALVPN (Assignment of LVP Code for Network Data Memory)
KIND=2
Assign the SYS-ID Code
5) ALVPL (Assignment of LVP Code for Local Data Memory)
KIND=1
Assign the LVP Code (for each Node)
Note:LVP Code is assigned to the nodes which have ZTs.
6) ACSEN (Assignment of Expansion CS/ZT System Data for Network Data Memory)
 PHS Community Number : 1~1024
 Network Number : Only for Roaming Feature
 Additional Area Number : Only for Roaming Feature
 Country Number : 31A (USA) fixed
 Number of PHS-Manager Code : 0 fixed
 START
A 
						

							NDA-24301 CHAPTER 4
Page 105
Revision 1.0
OFFICE DATA ASSIGNMENT
2. Procedure to Add Operating ZT7) ACSDN (Assignment of CS/ZT Data for Network Data Memory)
This command is used to assign the ZT related data including the PHS Community No., Fusion 
Point Code, Calling Area No., Group No., ZT No., ZT LENS, ZT KIND.
When this data assignment is finished, 3B+D channels of the CSINT circuit card start-up.
 PHS Community Number : 1~1024
 FPC : Fusion Point Code
 Calling Area Number : 1-32
 Group Number : 1-8
 ZT Number : 1-32
 KIND : ZT kind : 4 (fixed)
TN : Tenant Number
 LENS : ZT Equipment Number
Note:If NDM was not copied to the Local Nodes(s) after the last initialization, please broadcast it
using CBCN command.
1) Installation of Additional ZT
2)Call LVP Server system
3) ALVPL (Assignment of LVP Code for Local Data Memory)
KIND=1
Assign the LVP Code
4) ACSDN (Assignment of CS/ZT Data for Network Data Memory)
This command is used to assign the ZT related data including the PHS Community No., Fusion 
Point Code, Calling Area No., Group No., ZT No., ZT LENS, ZT KIND.
When this data assignment is finished, 3B+D channels of the CSINT circuit card start-up.
 PHS Community Number : 1~1024
 FPC : Fusion Point Code
 Calling Area Number : 1-32
 Group Number : 1-8
 ZT Number : 1-32
 TN : Tenant Number
 LENS : ZT Equipment Number
 END
A
 START
 END 
						

							CHAPTER 4 NDA-24301
Pag e 1 06
Revision 1.0
OFFICE DATA ASSIGNMENT
3. ZT Deletion Procedure
1) MBCSN ( MAKE BUSY CS/ZT for Network Data Memory)
2) ACSDN (Assignment of CS/ZT Data for Network Data Memory)
Delete the ZT Data.
 START
 END 
						

							NDA-24301 CHAPTER 4
Page 107
Revision 1.0
OFFICE DATA ASSIGNMENT
2.3 PS OFFICE DATA ASSIGNMENT
Below are explanations about assigning office data to place the PS in operation in the Built-in PCS system.

The port is automatically occupied for each PS assignment from the bigger numbered port (MG=31,U=3, G=23,
Level=7) to the smaller. When adding UNIT to the system later, you must concern about the number of assigned
PS (for example, if 192 PSs are assigned, the biggest numbered UNIT can not be used for the station
assignment). Conversely, if a station data is assigned against the biggest numbered MG, PS can not be assigned
to your system.
1. Initial Start-UP of the PS
2. Addition of the PS 
						

							CHAPTER 4 NDA-24301
Pag e 1 08
Revision 1.0
OFFICE DATA ASSIGNMENT
1) AFMU
Note:When a PS is assigned by APSD command, logically it occupies a port from module group
(MG) 31 to 26, from larger number of MG to smaller. Using AFMU command, those MGs must
be assigned for Fusion Network.
Since One MG can contain up to 768 PSs in it, for instance. If you need maximum of 4000 PSs
in a node, MG31, 30, 29, 28, 27 and 26 must be assigned.
At the beginning of installation, you do not have to allocate all six MGs in a node, just the
aamount needed at the time. Later, when you need to add more PSs to the node, you can come
back to AFMU again. ALGSN command will tell you when it’s time by giving you an error in
assigning telephone number to a MG which has not been assigned yet.
2) APSD (Assignment of the PS Operation Data for DM)
This command assigns the PS operation data including its tenant No., station No., Service Feature 
Restriction Class (SFC) and the Route Restriction Class (RSC) in consideration of the numbering 
plan/restriction data.
 TN : Tenant
 PS STN : PS Station Number
 KIND : PS KIND :6 (My Line) or 7 (Sub Line)
 RSC : Route Restriction Class
 SFC : Service Feature Restriction Class
 PS-ID : Max. 9 [DEC]
 PSNO : PS KIND : 2 (13 digits or less [BCD]) fixed
  NO. : Assign the same number as the PS NO. according to PS KIND.
 NWN : Network Number   : Only for Roaming Feature
 ADERA : Additional Area Number  : Only for Roaming Feature
 CTRN : Country Number   : 794 (USA) fixed
 Sub-Sysid : Number of Sub-Sysid   : Not used
3) ALGSN (Assignment of Telephone Number Data for Network Data Memory)
Refer to “Office Data Specification Manual”.
4) APDLN (Down loads of PS Operation Data) This command loads the PS operation data to the PS.
 UGN
 PS Telephone Number : Max. 16 Digits
TYPE=2
 PS No. : Max. 13 Digits
Note:If CBCN has never been done in Fusion Network after the last initialization, please do
CBCN before ALGNN.
 END
 START 
						

							NDA-24301 CHAPTER 4
Page 109
Revision 1.0
OFFICE DATA ASSIGNMENT
3. Deletion of the PS data
1) ALGSN (Assignment of Telephone Number Data for Network Data Memory)
Delete the Telephone Number and LENS related.
2) APSD (Assignment of the PS Operation Data for DM)
Using this command, delete the PS data to be cleared such as tenant No., station No., SFC and 
RSC.
Note:If CBCN has never been done in Fusion Network after the last initialization, please do CBCN
before ALGSN.
 END
 START 
						

							CHAPTER 4 NDA-24301
Pag e 1 10
Revision 1.0
OFFICE DATA ASSIGNMENT
3.  ASSIGNM ENT  OF  SER VICE  F E ATURE  DATA
This section describes how to assign  the data for the  following serv ice features.
 Automatic Announcement-PS Out of Zone/C.F.-PS Incoming Incomplete
 Automatic Announcement-Disconnected PS Out of Zone
 Name Display
 Name Display-CCIS
 Number Sharing
PCS Roaming
 TTC Q. 931a protocol Tie Line with PCS Roaming
 Two-Line Operation
 Voice Mail Indication (VMI)
 ZT Program Download
 Call Forwarding-Dropped Calls
 Data Communications-32 kbps
 Authorization Code
Call Park
 Group Call-Automatic Conference (20-party)
 Short Text Message Service
PCS ↔Nurse Call Integration
 Speed Calling - System 
						

							NDA-24301 CHAPTER 4
Page 111
Revision 1.0
OFFICE DATA ASSIGNMENT
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
1. GENERAL DESCRIPTION
When a call cannot terminate to a PS which is Out of Zone or whose power is OFF, the system automatically
answers the call and provides an announcement to notify the calling party that the called PS is Out  of Zone or
if the C.F.-PS Incoming Incomplete is set to a given destination, the aborted call can be transferred to the
preprogrammed station or PS.
2. OPERATING PROCEDURE
No manual operation.
3. SERVICE CONDITIONS
1. C.F.-PS Incoming Incomplete can be programmed and cancelled with the PS by pressing Access
Code+target station number (transferred station number).
2. When the PS is Out of Zone or its power is OFF, and the call is an incoming call directly via the Attendant
Console, the caller does not hear the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE, but hears the
following tones.
 DIT: RBT is heard
 REMOTE ACCESS TO SYSTEM: BT is heard
 AUTOMATED ATTENDANT: BT is heard
 ATTENDANT CONSOLE : BT is heard
 ISDN-DID ADDRESSING: Announcement of ISDN (PSTN) is heard.
3. One system is given one kind of recorded message for the AUTOMATIC ANNOUNCEMENT-PS OUT OF
ZONE.
4. On the condition that both the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE and C.F.-PS
INCOMING INCOMPLETE are assigned to a PS, priority is given to the C.F.-PS INCOMING
INCOMPLETE.
5. If an incoming call terminated at the very moment when a PS user is setting the C.F.-PS INCOMING
INCOMPLETE with a Pre-Set Dialing (before OFF-HOOK), the procedure becomes invalid.
6. If another transfer service is set to the target destination party of the C.F.-PS INCOMING INCOMPLETE,
the call is transferred to the last end party.
7. When a call is transferred to another PS activated by the C.F.-PS INCOMING INCOMPLETE and when the
call termination is not completed, the caller can hear the announcement if the AUTOMATIC
ANNOUNCEMENT-PS OUT OF ZONE is assigned.
8. When the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE is activated but all the announcement
trunks are busy (single connection: AAED M=0), the calling party encounters BT.
9. AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE does not allow the incoming call from outside to
be connected to announcement trunk. The calling party hears RBT. 
						

							CHAPTER 4 NDA-24301
Pag e 1 12
Revision 1.0
OFFICE DATA ASSIGNMENT
10. The incoming incomplete call to PS can be transferred to other PSs, stations, Attendant Consoles, Central
Office and TIE lines when the C.F.-INCOMING INCOMPLETE is in service.
11. The timer value of incoming incomplete call is approximately eight seconds, time duration until the system
recognizes that the PS is Out of Zone from an incoming call attempt to the PS.
Priority is given to the C.F.-INCOMING INCOMPLETE over the C.F.-DON’T ANSWER.
12. C.F.-PS INCOMING INCOMPLETE is not activated in an incoming call from ISDN and an incoming call
via the Attendant Console. The caller encounters the AUTOMATIC ANNOUNCEMENT-PS OUT OF
ZONE or BT.
13. When a forwarded station for the C.F.-PS INCOMING INCOMPLETE sets the CALL FORWARDING-
ALL CALLS to the announcement, the C.F.-PS INCOMING INCOMPLETE is not activated, instead the
caller hears BT.
14. In the Fusion Network, every node must have one or more Announcement Trunk.
15. When incoming call comes from ISDN Network, and the timer (T310) of the Network side is expired, the
caller hears the Announcement from Network side.
16. When a call in two-way connection is transferred to the PS which is out of zone, the system does not provide
the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE (i.e. the call is not connected to the
announcement trunk). 
						

							NDA-24301 CHAPTER 4
Page 113
Revision 1.0
OFFICE DATA ASSIGNMENT
4. PROGRAMMING
4-1 Automatic Announcement-PS Out of Zone
 Entry Procedure
1) ARTD (Route Class Data)
Assign the Route Class Data for announcement trunk.
RT : Route Number
OSGS (CDN: 1) = 2
ONSG (CDN: 2) = 2
TF (CDN: 5) = 1
TCL (CDN: 6) = 4
L/T (CDN: 7) = 1
ANS (CDN28) = 1
Assign “0” for other parameters.
2) ALRTN (Assignment of Logical RT for Network Data Memory)
LGRT : Logical Route Number
FPC : Fusion Point Code
RT : Route Number
Note:Not Necessary in the standalone situation.
3) ATRK (Trunk Data)
Assign the data for the announcement trunk.
RT : Route Number
TK : Trunk Number
LENS : Line Equipment Numbers (6 digits)
TN : Tenant Number
4) MBTK (Make Busy of Trunk)
Set the announcement trunk in a make-busy cancel state.
5) ARSC (Route Restriction Class Data)
Assign a Route Restriction Class (RSC) to the station which allows access to the announcement 
route.
D/N : Day/Night Mode
TN : Tenant Number
RT : Route Number
RSC : Route Restriction Class (0-15)
RRI :  Route Restriction Index (0-3)
RES = 1 (Allowed)
A
 START