NEC Neax 2400 Ipx Wireless System Manual

							CHAPTER 5 NDA-24301
Pag e 2 54
Revision 1.0
ASYD  : Assignment of System Data
1. GENERAL
The ASYD/ASYDL command is used to assign the system data of the following node;
Local Node (LN) / Network Control Node (NCN) of the Fusion network.
Stand alone PBX.
List Up Command: LSYD
2. PRECAUTIONS
This part describes only the contents of the command added in Built-in PCS system. For more details, refer to
the “Office Data Specification.” 
						

							NDA-24301 CHAPTER 5
Page 255
Revision 1.0
3. DATA ENTRY INSTRUCTIONS
Define each bit corresponding
data with referring to the
SYSTEM DATA CONTENTS
SYSTEM
DATA
TYPE
( SYS )DATA
( DATA )
00-FF
( Hex ) SYSTEM
DATA
INDEX
( INDEX )
0 - 511
BIT CORRE-
SPONDING
DATA
DATA
0 / 1BITSYSTEM DATA CONTENTS
DATA
DATA BIT
BIT
DATA
Hex 1
1b0
b1
b2
b3
b4
b5
b6
b7 1
0
0
0
0
0
0n
n+1 FF031
1
0
0
0
0
0
0b0
b1
b2 Not used
Not used
Not used
Not used
Not used
Not used
Number of zzz b3
b4
b5
b6
b7xxx service 0/1=Not to be provided/  To be provided
yyy service 0/1=Not to be provided/  To be provided
Convert from Binary DATA
to Hexadecimal, and enter the
Hex. value at DATA text box.
00000011 b7 b6 b5 b4 b3 b2 b1 b0
03 
						

							CHAPTER 5 NDA-24301
Pag e 2 56
Revision 1.0
SYSTEM
DATA
TYPE 
(SYS)SYSTEM 
DATA  
INDEX 
(INDEX)
0 - 511DATA 
(DATA) 
00-FF 
(Hex)BIT CORRE-
SPONDING 
DATA
SYSTEM DATA CONTENTS
DATA 
0/1BIT
15b
0
Access Code for C.F.-Busy Line and C.F. – Don’t Answer Services
0/1 = Same/Separate
Note 1:If a PCS system, C.F.-PS Incoming Call Incomplete also
refers to this system data.
Note 2:If “0” is assigned, assign either SID: 10 or 12 in
command “ASPA”.
b
1Maximum number of Multiple Call Forwarding – All Calls/Busy 
Line occurrences:
Note:This data is valid when SYS-1, INDEX 69, bit 7 is assigned
as “1”. b
2
b3
b4Miscellaneous Timer Counter 
(MTC)
(0-7)Call Back – Delay Timer
Timer Value Setting is MTC × 2 
sec.
When this data is “000”, Timer 
value is 2 sec. b
5
b6
b7Call Back – Delay Timer
0/1 = Ineffective/Effective
b3b2b1b3b2b1
000: 100:
001: 101:
010: 110:
011:111:
once
three times twice
five times four times 
						

							NDA-24301 CHAPTER 5
Page 257
Revision 1.0
4. SYSTEM DATA PROGRAMMING SHEET (1)
S
Y
S
1
SYSTEM
DATA
INDEX
0-511DATA
00-FFB
I
TSYSTEM DATA CONTENTS
30 060 Mounting Capacity of Data Memory (DM) : 1~63 Mbyte (01~3F) 
Normally assigned as “6” 
1
2
3
4
5
6
7
4200Access code using Pre-set dialing
 (e.g.: Special Access Code + Station number)
0/1 : Out/In service
1By cancelling C.F.-PS INCOMING INCOMPLETE
0 = C.F.-DROPPED CALL is also cancelled
1 = C.F.-DROPPED CALL is not cancelled
2Not used
3
4
5
6
7
b7 b6 b5 b4 b3 b2 b1 b0
00
Data
b7 b6 b5 b4 b3 b2 b1 b0
0000000
Data 
						

							CHAPTER 5 NDA-24301
Pag e 2 58
Revision 1.0
S
Y
S
1
SYSTEM
DATA
INDEX
0-511DATA
00-FFB
I
TSYSTEM DATA CONTENTS
4210 Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.1) Announcement PS-Out of 
Zone disconnection timer 
(Release Guard timer)
Timer value setting is as 
follows: (TC) sec. × (MTC)
When the data is assigned as 
00, the default data is 30 sec. 1
2
3
4 Timer class (TC)
0 : –  3 : 2 sec.  6 : –
1 : – 4 : – 7 : –
2 : –  5 : – 5
6
7 Not used
4220Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.2) No-tone connection timer to 
the called party during the 
handover
Timer value setting is as 
follows: 800 msec.+ (TC) × 
(MTC)
When the data is assigned as 
00, the default data is 800 
msec. 1
2
3
4Timer class (TC)
0 : –  3 : –  6 : –
1 : 64 msec. 4 : –  7 : –
2 : –  5 : – 5
6
7Not used
4230 Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.3) ZT start-up Guard Timer 
when initialization is in 
progress.
(This is the timer by which 
the ZT is placed out of Zone 
and made send PS location 
registration.)
Timer value setting is as 
follows: (TC) sec.× (MTC)
When the data is assigned as 
00, the default data is 60 sec. 1
2
3
4 Timer class (TC)
0 : –  3 : 2 sec.  6 : –
1 : – 4 : 30 sec. 7 : –
2 : –  5 : – 5
6
7Not used
b7 b6 b5 b4 b3 b2 b1 b0
0
b7 b6 b5 b4 b3 b2 b1 b0
0
b7 b6 b5 b4 b3 b2 b1 b0
0 
						

							NDA-24301 CHAPTER 5
Page 259
Revision 1.0
AAED  : Assignment of Announcement Equipment Data
1. GENERAL
This command is used to assign the trunk information related to Announcement Equipment on a tenant basis. 
List Up Command: LAED
2. PRECAUTIONS
This part describes only the contents of the command added in PCS system. For more details, refer to the “Office
Data Specification”. 
						

							CHAPTER 5 NDA-24301
Pag e 2 60
Revision 1.0
3. DATA ENTRY INSTRUCTIONS
0 = Common 1 = Japanese
2 = English     3 = German
4 = French      5 = Spanish
6 = Chinese     7 = Russian
8-15 = Spare 
Note: LANG is available for the
Hotel application.
LANG
Enter EQP as the service feature provided by DAT. 
0 ~ 59     :
60       : ANNOUNCEMENT-PS-OUT OF ZONE
61      : AUTOMATIC ANNOUNCEMENT-PS-OUT OF ZONE CALL
62 ~ 127 :EQP
0 = Single connection
1 = Multiple connection M
TK parameter appears
if M=1 is entered. TK
0 = 30 seconds, and then disconnects
1 = The connection is held until the calling party released 
C
TENANT
NUMBER
( TN )ANNOUNCEMENT
EQUIPMENT
NUMBER
( EQP ) 0 - 127 KIND OF
LANGUAGE
( LANG )
0 - 15DURATION OF
CONNECTION
( C )
0 / 1SENDING
RBT
( R )
0 / 1ANSWER
SIGNAL
SENDING
( A )
0 / 1MULTIPLE
CONNECTION
( M )
0 / 1ROUTE
NUMBER
( RT )TRUNK
NUMBER
( TK )
Enter DAT route number assigned
by the ATRK command. RT
0 = Send RBT
1 = Do not send RBT 
R
0 = Answer Signal is not sent
1 = Answer Signal is sent 
A
Note:  Regarding this data, refer to the Office Data Specification.  Note   Note 
						

							NDA-24301 CHAPTER 5
Page 261
Revision 1.0
4. DATA SHEET
Note:Parameter LANG is available for the Hotel System.
TENANT 
NUMBER
(TN)ANNOUNCE
-MENT
EQUIPMENT
NUMBER
(EQP) 0-127KIND OFLANGUAGE
(LANG)
0-15
Note 
DURATION 
OF 
CONNEC-
TION (C)
0/1SENDING
RBT (R)
0/1ANSWER
SIGNAL
SENDING
(A) 0/1MULTIPLE
CONNEC-
TION
(M)0/1ROUTE
NUMBER
(RT)TRUNK
NUMBER
(TK)REMARKS 
						

							CHAPTER 5 NDA-24301
Pag e 2 62
Revision 1.0
ALGSL  : Assignment of Telephone Number Data for LDM
1. GENERAL
This command is used to assign the data pertaining to the relationship between the Telephone Number (TELN)
and physical station. 
List Up Command : LLGSL
2. PRECAUTIONS
1. This Telephone Number can be used in the self (local) node only. Use the ALGSN command if the
Telephone Number for the Fusion network is required.
2. TYPE parameter designates the programming method of physical station (the result is the same whichever
selected). When TYPE = 1 (LENS) is selected, the physical station which accommodates the Telephone
Number (TELN) is specified by the LENS. Likewise, TYPE = 2 (STN) is selected, the physical station
number (STN) is used.
3. The system data assignment (ASYDL, SYS1, INDEX513 Data 01hex) is needed to provide the Local Data
Memory (LDM).
4. The applicable tenant number (TN) range is designated by the ASYD command, SYS1, INDEX8.
5. When deleting the telephone number, the user must first delete the data which is concerned with Group
Calling Conference. 
						

							NDA-24301 CHAPTER 5
Page 263
Revision 1.0
3. DATA ENTRY INSTRUCTIONS
  TYPE = 1 (LENS is used to specify the Telephone number.)
  TYPE = 2 (STN is used to specify the Telephone number.)
TELEPHONE NUMBER
 (TELN) MAX. 16 DIGITSLINE EQUIPMENT NUMBER USER GROUP
NUMBER
(UGN)
UGN TYPE
 1 = User Group Number 1 (Fixed)
LENS
LENS of the physical stationTYPE
1 = LENS is used to specify the Telephone number
2 = STN is used to specify the Telephone number
1
1 1
1
(LENS)
11
TELN
Telephone number assigned by the 
ALGNL command
TELEPHONE NUMBER
 (TELN) MAX. 16 DIGITSSTATION
NUMBER
(STN) TENANT
NUMBER
(TN) USER GROUP
NUMBER
(UGN)
UGN TYPE
 1 = User Group Number 1 (Fixed)
STN
Station number of the 
physical stationTYPE
1 = LENS is used to specify the Telephone number
2 = STN is used to specify the Telephone number
1
1 2
2
TN
Tenant number of  the physical station
TELN
 Telephone number assigned by the ALGNL command