HP Photosmart C5383 User Manual

							
2.Slide the paper-width guide to its outermost position.
3.Insert the stack of paper into the main input tray with the short edge forward and the
print side down. Slide the stack of paper forward until it stops.
CAUTION: Make sure that the product is idle and silent when you load paper
into the main input tray. If the product is servicing the ink cartridges or otherwise
engaged in a task, the paper stop inside the product might not be in place. You
could push the paper too far forward, causing the product to eject blank pages.
TIP: If you are using letterhead, insert the top of the page first with the print side
down.
4. Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the main input tray; make sure the stack of paper fits within the main
input tray and is no higher than the top of the paper-width guide.
Chapter 6
38 Load originals and load paper
Load originals and load paper
 
						

							
5.Lower the output tray. Pull the tray extender towards you, as far as it will go. Flip the
paper catch at the end of the tray extender to open the extender the rest of the way.
NOTE: When you use legal-size paper, leave the tray extender closed.
To load up to 13 x 18 cm (5 x 7 inch) photo paper in the photo tray
1.Raise the photo tray lid.
2.Slide the paper-width guide to its outermost position.
Load paper 39
Load originals and load paper
 
						

							
3.Insert the stack of photo paper into the photo tray with the short edge forward and the
print side down. Slide the stack of photo paper forward until it stops.
If the photo paper you are using has perforated tabs, load the photo paper so that the
tabs are closest to you.
4.Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the photo tray; make sure the stack of photo paper fits within the
photo tray and is no higher than the top of the paper-width guide.
5.Lower the photo tray lid.
Load postcards, Hagaki, or index cards
You can load postcards, Hagaki, and index cards in the photo tray.
Chapter 6
40 Load originals and load paper
Load originals and load paper
 
						

							
To load postcards, Hagaki, or index cards in the photo tray
1.Raise the photo tray lid.
2.Slide the paper-width guide to its outermost position.
3.Insert the stack of cards into the photo tray with the short edge forward and the print
side down. Slide the sta ck forward until it stops.
4.Slide the paper-width guide inward against the stack of cards until it stops.
Do not overload the photo tray; make sure the stack of cards fits within the photo tray
and is no higher than the top of the paper-width guide.
Load paper 41
Load originals and load paper
 
						

							
5.Lower the photo tray lid.
Load envelopes
You can load one or more envelopes into the main input tray of the HP All-in-One. Do not
use shiny or embossed envelopes or envelopes that have clasps or windows.
NOTE: For specific details on how to format text for printing on envelopes, consult
the help files in your word processing software. For best results, consider using a label
for the return add ress on envelopes.
To load envelopes
1.Raise and hold the output tray in the open position.
2.Remove all paper from the main input tray.
Chapter 6
42 Load originals and load paper
Load originals and load paper
 
						

							
3.Slide the paper-width guide to its outermost position.
4.Insert one or more envelopes  into the far-right side of the main input tray, with the
envelope flaps on the left and facing up. Slide the stack of envelopes forward until it
stops.
TIP: To avoid paper jams, tuck the flap inside each envelope.
5.Slide the paper-width guide inward against the stack of envelopes until it stops.
Do not overload the main input tray; make sure the stack of envelopes fits within the
main input tray and is not higher than the top of the paper-width guide.
Load paper 43
Load originals and load paper
 
						

							
6.Lower the output tray.
Related topics
“
Print a group of addresses on labels or envelopes” on page 67
Load other types of paper
The following types of paper are designed for special projects. Create your project in the
HP Photosmart Software or another application, set the paper type and size, and then
print.
HP Premium Inkjet Transparency Film
▲Insert the film so that the white transparency strip (with arrows and the HP logo) is on
top and is going into the input tray first.
NOTE: The HP All-in-One cannot automatica lly detect the paper type. For best
results, set the paper type to transparency film in the software before printing onto
transparency film.
HP Iron-On Transfers
1. Flatten the transfer sheet completely before using it; do not load curled sheets.
TIP: To prevent curling, keep transfer sheets sealed in the original package until
you are ready to use them.
2. Locate the blue stripe on the nonprinting side of the transfer paper and then manually
feed one sheet at a time into the input tray with the blue stripe facing up.
HP Greeting Cards, HP Photo Greeting Cards, or HP Textured Greeting Cards
▲ Insert a small stack of HP greeting card paper into the input tray with the print side
down; slide the sta ck of cards forward until it stops.
TIP:Make sure the area on which you want to  print is inserted first, print side
down in the input tray.
Related topics
•“
Set the paper size” on page 52
•“
Set the paper type for printing” on page 53
•“
Print on transparencies” on page 67
Chapter 6
44 Load originals and load paper
Load originals and load paper
 
						

							
•“Reverse an image for iron-on transfers” on page 66
•“
Print a group of addresses on labels or envelopes” on page 67
Load a CD/DVD
In addition to printing on paper, the HP All-in-One enables you to print directly on the
surface of specially coated CDs and DVDs for print jobs started from a connected
computer. You can design and create a custom label for your CD or DVD using the
software that came with the HP All-in-One. You can then print the label on your printable
CD or DVD media.
TIP: It is recommended that you write your da ta to the CD or DVD before printing
the label on it.
NOTE: The HP All-in-One does not support a CD/DVD print job started from the
control panel. You must use the software that came with the HP All-in-One to print on
a CD/DVD. For more information, see the software help.
To load a regular-size (120 mm) CD/DVD on the CD/DVD tray
1. If the product is placed close to a wall, move it at least 7.5 cm (3 inches) away from
the wall.
2. Carefully remove the CD/DVD holder from the storage area below the main paper
tray.
3.Securely snap the inkjet printable media onto the CD/DVD holder with the printable
side up.
NOTE: The CD/DVD should be placed on the ring at the end of the holder with
the arrows.
Load a CD/DVD 45
Load originals and load paper
 
						

							
4.Lower the CD/DVD tray.
The CD/DVD tray is located just below the control panel. When in its lowered position,
the CD/DVD tray sits on top of the output tray.
5.Push the CD/DVD holder into the product until the white lines on the CD/DVD holder
line up with the white lines on the CD/DVD tray, and then press  OK.
NOTE: The product pulls the CD/DVD holder while printing on the media.
6.After printing, make sure you insert the CD/DVD holder back into the storage area.
Chapter 6
46 Load originals and load paper
Load originals and load paper
 
						

							
To load a small-size (80 mm) CD/DVD on the CD/DVD tray
1.If the product is placed close to a wall, move it at least 7.5 cm (3 inches) away from
the wall.
2. Carefully remove the CD/DVD holder from the storage area below the main paper
tray.
3.Securely snap the inkjet printable media onto the CD/DVD holder with the printable
side up.
NOTE: The CD/DVD should be placed on the ring at the end of the holder with
the arrows.
4. Flip the CD/DVD holder ring over the CD/DVD.
Load a CD/DVD 47
Load originals and load paper