HP Photosmart C5383 User Manual

							
4.Locate the sensor inside the product.
The sensor is a square, black plastic part  slightly larger than a pencil eraser, just
to the left of the print carriage.
5. Wipe the sensor with a dry swab or lint-free cloth.
6. Close the ink cartridge access door, and check if the error message has been
resolved.
7. If you still receive the error message, turn the product off, and then on again.
Cause: Ink might have built up and covered the sensor.
If this did not solve the issue, try the next solution.
Solution 2: Clean the sensor windows on the ink cartridges Solution: Clean the window on all of the ink cartridges.
If the problem is not resolved, printing can continue, but the ink system behavior might
change.
CAUTION: The cleaning procedure should take only a few minutes. Make sure
that the ink cartridges are reinstalled in the product when instructed. Leaving them
outside of the product for an extended period of time can result in damage to the
ink cartridges.
To clean the sensor window on the ink cartridges
1. Gather swabs or a lint-free cloth to use for the cleaning procedure.
2. Make sure the product is turned on.
3. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
Chapter 14
268 Troubleshooting
Troubleshooting
 
						

							
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
4.Remove all of the ink cartridges and place them on a piece of paper with the ink
openings pointing up.
To remove the ink cartridges
a. Press the tab on the ink cartridge to release it, and then remove it from the
slot.
b. Place the ink cartridge on a sheet of paper with the ink opening pointing up.
c. Repeat steps a and b for each ink cartridge.
5. For each ink cartridge, wipe the sensor window with a dry swab or lint-free cloth.
The sensor window is an area of clear plastic near the copper or gold-colored
metal contacts on the bottom of the ink cartridge. Try not to touch the metal
contacts.
Errors 269
Troubleshooting
 
						

							
6.Install each ink cartridge in its slot. Press it down until the tab snaps into place.
Match the color and icon on each ink cartridge label to the color and icon on the
slot for that ink cartridge.
7.Close the ink cartridge access door, and check if the error has been resolved.
8. If you still receive the error message, turn the product off, and then on again.
Cause: Ink might have built up on the ink cartridge window and it needed to be
cleaned
If this did not solve the issue, try the next solution.
Solution 3: Contact HP support
Solution: Contact HP support for service.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for information
on calling for te chnical support.
Cause: The sensor was defective.
Ink cartridge is missing, incorrectly installed, or not intended for your product
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Insert  all ink cartridges
•
Solution 2: Check if all ink cartridges are properly installed
•
Solution 3: Clean the ink cartridge contacts
•
Solution 4: Contact HP support
Solution 1: Insert all ink cartridges Solution: Make sure all of the ink cartridges are inserted.
For more information, see:
“
Replace the ink cartridges” on page 101
Cause: One or more ink cartridges were missing.
If this did not solve the issue, try the next solution.
Chapter 14
270 Troubleshooting
Troubleshooting
 
						

							
Solution 2: Check if all ink cartridges are properly installedSolution: Make sure all of the ink cartridges are properly installed. Refer to the
following steps to resolve this error.
To make sure the ink cartridges are properly installed
1. Make sure the product is turned on.
2. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
3.Make sure the ink cart ridges are installed in the correct slots.
Match the shape of the icon and color of the ink cartridge with the slot that has
the same shaped icon and color.
4. Run your finger along the top of the ink cartridges to locate any cartridges that
are not snapped completely down.
5. Press down on any cartridges that are sticking up.
They should snap down into place.
Errors 271
Troubleshooting
 
						

							
6.If an ink cartridge was sticking up and you were able to snap it back down into
place, close the ink cartridge access door and check if the error message has
gone away.
• If the message has gone away, stop troubleshooting here. The error has been
resolved.
• If the message has not gone away, proceed to the next step.
• If none of the ink cartridges were sticking up, proceed to the next step.
7. Locate the ink cartridge that is indicated in the error message, and then press the
tab on the ink cartridge to release it from the slot.
8.Press the ink cartridge back down into place.
The tab should make a snapping noise when the ink cartridge is correctly seated.
If the ink cartridge did not make a snapping noise, the tab might need to be
readjusted.
9. Remove the ink cartridge from the slot.
10. Gently bend the tab away from the ink cartridge.
CAUTION: Be careful not to bend the tab out more than about 1.27 cm
(0.5 inches).
Chapter 14
272 Troubleshooting
Troubleshooting
 
						

							
11.Reinstall the ink cartridge.
It should now snap down into place.
12.Close the ink cartridge access door, and check if the error message has gone
away.
13. If you still receive the error message, turn the product off, and then on again.
For more information, see:
“
Replace the ink cartridges” on page 101
Cause: One or more of the ink cartridges were not installed.
If this did not solve the issue, try the next solution.
Solution 3: Clean the ink cartridge contacts Solution: Clean the ink cartridge electrical contacts.
If you still receive this message after cleaning the ink cartridge contacts, you might
have a damaged ink cartridge.
To clean the electrical contacts
1. Make sure the product is turned on.
2. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
Errors 273
Troubleshooting
 
						

							
3.Locate the ink cartridge that is indicated in the error message, and then press the
tab on the ink cartridge to release it from the slot.
4.Hold the ink cartridge by its sides with the bottom pointing up and locate the
electrical contacts on the ink cartridge.
The electrical contacts are four small rectangles of copper or gold-colored metal
on the bottom of the ink cartridge.
1Ink window
2Electrical contacts
5.Wipe the contacts with a dry swab or lint-free cloth.
CAUTION: Be careful not to move any ink or other debris onto the clear
plastic ink window next to the contacts.
6. On the inside of the product, locate the contacts in the printhead.
The contacts look like a set of four copp er or gold-colored pins positioned to meet
the contacts on the ink cartridge.
7. Use a dry swab or lint-free cloth to wipe the contacts.
Chapter 14
274 Troubleshooting
Troubleshooting
 
						

							
8.Reinstall the ink cartridge.
9.Close the ink cartridge door, and check if the error message has gone away.
10. If you still receive the error message, turn the product off, and then on again.
Check to see if your ink cartridge is still under warranty and the end of warranty date
has not been reached.
• If the end of warranty date has been reached, purchase a new ink cartridge.
• If the end of warranty date has not been reached, contact HP support for service
or replacement.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for
information on calling for technical support.
For more information, see:
•“
Ink cartridge warranty information” on page 281
•“
Replace the ink cartridges” on page 101
•“
Clean the printhead” on page 105
Cause: The indicated ink cartridge contacts were defective.
If this did not solve the issue, try the next solution.
Solution 4: Contact HP support Solution: Contact HP support for service.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for information
on calling for technical support.
Cause: The ink cartridges were not intended for use in this product.
Sensor failure
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Clean the sensor
•
Solution 2: Clean the sensor windows on the ink cartridges
•
Solution 3: Contact HP support
Errors 275
Troubleshooting
 
						

							
Solution 1: Clean the sensorSolution: Clean the sensor.
If the problem is not resolved, printing can continue, but the ink system behavior might
change.
CAUTION: The cleaning procedure should take only a few minutes. Make sure
that the ink cartridges are reinstalled in the product when instructed. Leaving them
outside of the product for an extended period of time can result in damage to the
ink cartridges.
To clean the sensor in the product
1. Gather swabs or a lint-free cloth to use for the cleaning procedure.
2. Make sure the product is turned on.
3. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
4.Locate the sensor inside the product.
The sensor is a square, black plastic part  slightly larger than a pencil eraser, just
to the left of the print carriage.
5. Wipe the sensor with a dry swab or lint-free cloth.
6. Close the ink cartridge access door, and check if the error message has been
resolved.
7. If you still receive the error message, turn the product off, and then on again.
Cause: Ink might have built up and covered the sensor.
Chapter 14
276 Troubleshooting
Troubleshooting
 
						

							
If this did not solve the issue, try the next solution.
Solution 2: Clean the sensor windows on the ink cartridgesSolution: Clean the window on all of the ink cartridges.
If the problem is not resolved, printing can continue, but the ink system behavior might
change.
CAUTION: The cleaning procedure should take only a few minutes. Make sure
that the ink cartridges are reinstalled in the product when instructed. Leaving them
outside of the product for an extended period of time can result in damage to the
ink cartridges.
To clean the sensor window on the ink cartridges
1. Gather swabs or a lint-free cloth to use for the cleaning procedure.
2. Make sure the product is turned on.
3. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
4.Remove all of the ink cartridges and place them on a piece of paper with the ink
openings pointing up.
To remove the ink cartridges
a. Press the tab on the ink cartridge to release it, and then remove it from the
slot.
Errors 277
Troubleshooting