HP Photosmart C5383 User Manual

							
Carriage stall
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Print a printer status report
•
Solution 2: Remove objects blocking the path
•
Solution 3: Ensure that the product is connected to a suitable power source
Solution 1: Print a pr inter status report
Solution: Print a printer status report to see if the product can print.
For more information, see:
“
Print and evaluate a print quality report” on page 107
If the product can print a printer status re port and can print from the computer (if
applicable), then there is no need to follow the remaining solutions, as the error
message might be false.
Cause: The error was false.
If this did not solve the issue, try the next solution.
Solution 2: Remove objects blocking the path Solution: Remove any objects, such as paper, that are blocking the print carriage
path. Then reset the product.
To clear the print carriage
1. Leave the product on and then disconnect the power cord and the USB cable
from the back of the product.
CAUTION: Make sure the product is on before disconnecting the power
cord. Failure to disconnect the power cord from the rear of the product can
cause damage when removing jammed paper. Do not reconnect the power
cord and USB cable until instructed to later.
2. Open the ink cartridge access door by lifting from the front center of the product,
until the door  locks into place.
Chapter 14
238 Troubleshooting
Troubleshooting
 
						

							
3.Make note of where the print carriage is stuck and look for jammed paper.
A paper jam can cause the error message and the print carriage to stall.
CAUTION: Do not use any tools or other devices to remove jammed paper.
Always use caution when removing jammed paper from inside the product.
If the print carriage is stuck on the left side
a . Check for any paper or object that may be restricting the print carriage.
b . Move print carriage all the way to the right side.
c . Check the paper path all the way to the left side and remove any paper still
in the product.
If the print carriage is stuck in the middle
a . Check for any paper or object that may be restricting the print carriage.
b . Move print carriage all the way to the left side.
c . Check the paper path all the way to the right side and remove any paper still
in the product.
d . Move print carriage all the way to the right side.
e . Check the paper path all the way to the left side and remove any paper still
in the product.
4. Close the ink cartridge access door.
5. Check for a paper jam in the back of the product.
6. Reconnect only the power cord. If the product does not automatically turn on,
press the On button.
NOTE: The product might go through a warm-up period of up to two minutes.
Lights might flash and the print carriage might move. Wait until this warm-up
period is complete before going to the next step.
7. Do one of the following, depending upon the state of the product:
• If the On button light is on and steady, print a printer status report. If you can
print a printer status report, the carriage is no longer jammed.
See the following task for information about printing a printer status report.
• If the On button light is not on or is flashing and the print carriage is still stalled, proceed to the next solution.
8. Reconnect the USB cable.
Errors 239
Troubleshooting
 
						

							
To clear a paper jam from the rear door
1.Press in the tab on the left side of the rear door to release the door. Remove the
door by pulling it away from the product.
2.Gently pull the paper out of the rollers.
CAUTION: If the paper tears when you are removing it from the rollers, check
the rollers and wheels for torn pieces of paper that might be remaining inside
the product. If you do not remove all the pieces of paper from the product,
more paper jams are likely to occur.
3. Replace the rear door. Gently push the door forward until it snaps into place.
4.Press  OK on the control panel to continue the current job.
Cause: The print carriage was blocked by a paper jam.
If this did not solve the issue, try the next solution.
Solution 3: Ensure that the product is connected to a suitable power source Solution: Verify that the product is properly connected to a suitable power source.
To verify the product is connected to a suitable power source
1. Make sure that you are using the power cord provided with the product.
2. If the product is connected to a computer, make sure the computer has a
grounded (three-prong) power plug.
3. Make sure the power cord is firmly connected to both the product and the power
adaptor.
Chapter 14
240 Troubleshooting
Troubleshooting
 
						

							
4.Plug the power cord directly into a power outlet.
1Power connection
2Power cord and adaptor
3Power outlet
5.Try to print from your computer.
If the product prints when plugged directly into a power outlet while disconnected
from any power strips or surge suppressors, the power strip or surge suppressor
might not be allowing sufficient voltage to reach the product.
6. If the product cannot print and the print carriage is still stalled, contact HP support
for service.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for
information on calling for technical support.
Cause: There might not be sufficient voltage for the product.
Cartridges in wrong slot
Solution: Remove and reinsert the indicated in k cartridges into the correct slots by
matching color of cartridges to color and icon for each slot.
Errors 241
Troubleshooting
 
						

							
Printing cannot occur without one of each type of ink cartridge inserted into the correct
slot.
For more information, see:
“
Replace the ink cartridges” on page 101
Cause: The indicated ink cartridges were inserted into the wrong slots.
General printer error
Solution: Write down the error code provided in the message, and then contact HP
support. Go to:
www.hp.com/support
If prompted, choose your country/region, and then click  Contact HP for information
on calling for te chnical support.
Cause: There was a problem with the product.
Incompatible ink cartridges
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Check to see if the ink cartridges are compatible
•
Solution 2: Contact HP support
Solution 1: Check to see if the ink cartridges are compatible Solution: Check to make sure you are using the correct ink cartridges for your
product. For a list of compatible ink cartridges, see the printed documentation that
came with the product.
If you are using ink cartridges that are not compatible with the product, replace the
indicated ink cartridges with ink cartridges that are compatible.
CAUTION: HP recommends that you do not remove an ink cartridge until a
replacement is ready to install.
If it appears that you are using the correct ink cartridges, proceed to the next solution.
For more information, see:
•“
Shop for ink supplies” on page 115
•“
Replace the ink cartridges” on page 101
Cause: The indicated ink cartridges were not intended for use in this product as it
was currently configured.
If this did not solve the issue, try the next solution.
Chapter 14
242 Troubleshooting
Troubleshooting
 
						

							
Solution 2: Contact HP supportSolution: Contact HP support for service.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for information
on calling for technical support.
Cause: The ink cartridges were not intended for use in this product.
Incompatible printhead
Solution: Contact HP support for service.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for information
on calling for technical support.
Cause: The printhead was not intended for use in this product, or it was damaged.
Ink alert
Solution: When you receive an Ink Alert message, you do not need to replace the
indicated ink cartridge. However, the amount of ink might be low enough to cause
poor print quality. Follow any prompts on the display to continue.
CAUTION: HP recommends that you do not remove an ink cartridge until a
replacement is ready to install.
HP recommends that you do not remove an ink cartridge until a replacement is ready
to install.
If you have installed a refilled or remanufactured cartridge, or a cartridge that has
been used in another product, the ink level indicator might be inaccurate or
unavailable.
Ink level warnings and indicators provide estimates for planning purposes only. When
you receive an ink alert message, consider having replacement ink cartridges
available to avoid possible printing delays.
For more information, see:
“
Replace the ink cartridges” on page 101
Cause: The indicated ink cartridges did not have enough ink to print properly.
Ink cartridge problem
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Install the ink cartridges correctly
•
Solution 2: Clean the electrical contacts
•
Solution 3: Close the print carriage latch
Errors 243
Troubleshooting
 
						

							
•Solution 4: Replace the ink cartridge
•
Solution 5: Contact HP support
Solution 1: Install the ink cartridges correctly Solution: Make sure all of the ink cartridges are properly installed. Refer to the
following steps to resolve this error.
To make sure the ink cartridges are properly installed
1. Make sure the product is turned on.
2. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
3.Make sure the ink cartridges ar e installed in the correct slots.
Match the shape of the icon and color of the ink cartridge with the slot that has
the same shaped icon and color.
4. Run your finger along the top of the ink cartridges to locate any cartridges that
are not snapped completely down.
5. Press down on any cartridges that are sticking up.
They should snap down into place.
Chapter 14
244 Troubleshooting
Troubleshooting
 
						

							
6.If an ink cartridge was sti cking up and you were able to snap it back down into
place, close the ink cartridge access door and check if the error message has
gone away.
• If the message has gone away, stop troubleshooting here. The error has been resolved.
• If the message has not gone away, proceed to the next step.
• If none of the ink cartridges were sticking up, proceed to the next step.
7. Locate the ink cartridge that is indicated in the error message, and then press the
tab on the ink cartridge to release it from the slot.
8.Press the ink cartridge back down into place.
The tab should make a snapping noise when the ink cartridge is correctly seated.
If the ink cartridge did not make a snapping noise, the tab might need to be
readjusted.
9. Remove the ink cartridge from the slot.
10. Gently bend the tab away from the ink cartridge.
CAUTION: Be careful not to bend the tab out more than about 1.27 cm
(0.5 inches).
Errors 245
Troubleshooting
 
						

							
11.Reinstall the ink cartridge.
It should now snap down into place.
12.Close the ink cartridge access door, and check if the error message has gone
away.
13. If you still receive the error message, turn the product off, and then on again.
Cause: The indicated ink cartridges were not installed correctly.
If this did not solve the issue, try the next solution.
Solution 2: Clean the electrical contacts Solution: Clean the electrical contacts.
CAUTION: The cleaning procedure should take only a few minutes. Make sure
that the ink cartridges are reinstalled in the product when instructed. Leaving them
outside of the product for an extended period of time can result in damage to the
ink cartridges.
To clean the electrical contacts
1. Make sure the product is turned on.
2. Open the ink cartridge access door by lifting from the front right of the product,
until the door  locks into place.
The print carriage moves to the center of the product.
NOTE:Wait until the print carriage stops moving before proceeding.
Chapter 14
246 Troubleshooting
Troubleshooting
 
						

							
3.Locate the ink cartridge that is indicated in the error message, and then press the
tab on the ink cartridge to release it from the slot.
4.Hold the ink cartridge by its sides with the bottom pointing up and locate the
electrical contacts on the ink cartridge.
The electrical contacts are four small re ctangles of copper or gold-colored metal
on the bottom of the ink cartridge.
1Ink window
2Electrical contacts
5. Wipe the contacts with a dry swab or lint-free cloth.
CAUTION: Be careful not to move any ink or other debris onto the clear
plastic ink window next to the contacts.
6. On the inside of the product, locate the contacts in the printhead.
The contacts look like a set of four copp er or gold-colored pins positioned to meet
the contacts on the ink cartridge.
7. Use a dry swab or lint-free cloth to wipe the contacts.
Errors 247
Troubleshooting