GE S5 Owners Manual

							Frame for FM 49
Document no. M1187335-004
3.7 Adjustments and calibrations
It is not necessary to perform calibrations or adjustments on S/5 Frame for FM. 
						

							Datex-Ohmeda S/5 FM
50
Document no. M1187335-004
4Troubleshooting
4.1 S/5 Frame for FM
Table 6 S/5 Frame for FM troubleshooting chart
ProblemCause What to do
Monitor is not starting. 1. The batteries are empty. 2. Fuses may be blown.
3. If power cord connected, AC/DC unit may be faulty.
4. If AC/DC unit is working, the DC/ DC board may be faulty.
5. On/Stby key may be faulty. 1. Connect the power cord.
2. Replace fuses.
3. Replace the AC/DC power unit.
4. Replace the DC/DC unit.
5. Replace the command board 
panel keyboard foil.
Monitor is not starting. 1. The connection between DC/DC  board and CPU board may be 
faulty.
2. Faulty CPU board. 1. Check the connector and the 
interconnection board.
2. Replace the CPU board.
The monitor starts (alarm leds 
are lit and a beep is heard), but 
the display remains black. 1. The LCD display cables are loose.
2. The backlights are not lit.  1. Check the LCD display connection 
board connectors.
2. Check backlight connector. Check  inverter cable. 
Backlights may be faulty. Replace the 
backlights.
Backlight Inverter may be faulty. 
Replace the Inverter board.
Display and monitor operating 
but alarm leds not illuminating 
in start-up. 1. Loose connectors.
2. Ribbon cable faulty.
3. CPU not working. 1. Check all connectors from CPU to 
led board.
2. Replace ribbon cable.
3. Replace CPU.
Display and monitor operating 
but no audible beep in start-up. 1. Loudspeaker connector or wires 
loose or faulty. 1. Check loudspeaker connector and 
wires.
Display is too dim. 1. Incorrect brightness adjustment.
2. Backlight faulty.
3. Backlight inverter faulty. 1. Adjust display brightness higher.
2. Replace backlight.
3. Replace backlight inverter.
Stripes or white areas on screen. 1. Loose faulty display connection  flexboard connectors in CPU and 
display.1. Check display connection 
flexboard connectors in CPU and 
display.
Module data disappears from 
the screen. ‘Module power 
supply overload’ message. Parameter module current (in 
module bus) too high.
Detach and change parameter 
module.
Module data disappears. 1. Module bus voltage or signals  path broken.1. DC/DC board module power 
section may be faulty. Replace the 
DC/DC board.
2. Replace the Module bus cable  unit. 
						

							Frame for FM 51
Document no. M1187335-004
4.2 Memory option
Table 3 Memory option troubleshooting chart
‘Battery failure’ message on the 
screen. 1. Problem in communication 
between battery and DC/DC 
board.
2. Battery too old or defected.
3. DC/DC board may be faulty. 1. Replace battery.
2. Replace battery.
3. Replace the DC/DC board. 
Frame temperature high 
message. The temperature inside the frame is 
too high. Check monitor ventilation holes.
‘Battery temperature high’ 
message on the screen. Battery SMBus temperature is too 
high. Check monitor ventilation holes. 
Replace battery.
After shut off, the trend and 
patient data does not remain 15 
min in the memory. 1. The On/Stby switch has been 
pressed over 10 s. (= service 
reset).
2. Empty battery.
3. Only one battery inserted. 1. When switching off, the On/Stby 
switch has to be pressed less than 
10 s. 
2. Replace the battery.
3. Use always two batteries.
Keyboard not working, but 
module communication is OK. Keyboard cables and connectors, or 
interconnection board connectors 
may be faulty. Check the interconnection board 
connectors. 
Check the keyboard cable connection 
to the user interface board.
Keyboard not working, and 
module communication not 
working. UPI section of the CPU board not 
functioning normally.
Restart the monitor.
Replace the Central Processing 
Board.
Keyboard partly not working. 1. Keyboard faulty. 2. Keyboard cables and connectors, or interconnection board 
connectors may be faulty. 1. Replace the keyboard foil.
2. Check the interconnection board 
connectors. 
Check the keyboard cable connection 
to the user interface board.
Error message Cause What to do
‘No menus in Menu Card’ 
message There are no menus in the Menu 
card. Insert a Menu card with valid menu 
configuration file
s in the module.
‘Faulty Data Card - change card’ An error has occurred during Data  card read/write operation. Change Data card.
‘Faulty Menu Card - change card’ An error has occurred during Menu  card read/write operation. Change Menu card.
Problem Cause What to do 
						

							Datex-Ohmeda S/5 FM
52
Document no. M1187335-004
4.3 NET section
Table 4 NET section troubleshooting chart
ProblemCause What to do
Monitor does not connect to 
the network.
Monitor connects to the 
network, but disconnects 
unexpectedly (‘Network 
connection down’ message 
on the monitor screen). Patch panel 
Patch cable not connected to HUB or to panel.
Patch cable  Patch cable or connector defective.
HUB not connected to power supply.
HUB port closed due to physical layer problems.
HUB port temporarily closed and reopened due 
to physical layer problems.
Hubs not properly connected to each other.
Monitor-Network cable Cable not pro perly connected to the wallplate 
or to the monitor.
Cable or connector defective.
Network cable (inside the 
monitor) defective Replace the Network cable.
Network Connector Board 
defective Replace the Network Connector Board Unit.
Net section of the CPU board The NET section is defective. Replace the CPU  board.
NET section memory on the 
CPU board The SRAM of the NET section is defective or 
uninitialized. The NET cannot be used. See 
network service page for details.
Wrong identification number Use the Virtual ID number with monitors that  have WLAN option installed.
Identification plug There is no identification plug attached to the 
monitor.
The identification plug is defective or 
uninitialized. The plug cannot be used.
Multi I/O adapter faulty Replace multi I/O adapter. 
						

							Frame for FM 53
Document no. M1187335-004
‘Check network connectors’ 
message shows on the 
monitor screen Monitor-Network cable Cable not pro
perly connected to the wallplate 
or to the monitor.
Cable or connector defective.
Network cable (inside the 
monitor) defective Replace the Network cable.
Network Connector Board 
defective Replace the Network Connector Board Unit.
Multi I/O adapter faulty Replace multi I/O adapter.
Identification plug There is no identification plug properly attached  to the monitor.
The identification plug is defective or 
uninitialized. The plug cannot be used. See 
network service page for details.
‘Network board error’ 
message shows on the 
monitor screen NET section on the CPU board
NET section memory on the 
CPU board The NET section is defective. The board cannot 
be used. See network service page for details.
The SRAM memory of the NET section is 
defective or uninitialized. The board cannot be 
used. See network service page for details.
Other Site View shows no 
waveforms  No waveforms are set up for 
Monitor-to-Monitor 
communication Run Network Setup to veri
fy current Monitor-to-
Monitor communication setup.
Network printing fails Print server is busy
Print queue is full
Printer is off-line Network managers print server is busy at the 
moment and cannot take more print jobs. Try 
again after 15 seconds.
There are too many unprinted documents 
waiting in the print queue. Check the printer, as 
it is not operating properly.
Printer cable is loose, printer is out of paper, 
there is a paper jam or the printer is simply 
switched to off-line state.
Record keeper menus are 
blank There are no menus for the 
record keeper Run Network Setup to verify the current setup.
Problem Cause What to do 
						

							Datex-Ohmeda S/5 FM
54
Document no. M1187335-004
For your notes: 
						

							Appendix A Service check form, Datex-Ohmeda S/5 Frame for FM, F-FM
1(4)
                           Document no. M1187335-004
APPENDIX A: Service check form, 
Datex-Ohmeda S/5 Frame for FM, F-FM 
OK = Test OK            N.A. = Test not applicable            Fail = Test failed
Customer
 
Service Module type
S/N
Service engineer
 Date
 Monitor Installation
 
L- E- F-N-
N-N-N-N-
N-
 General
     OK           N.A.          Fail      OK           N.A.          Fail
1. Internal parts                            2. External parts
                           
3. Module installation                            4. Command Board LEDs
                           
5. Start-up                            6. Module recognition
                           
7. LCD display picture                            8. Time and date
                           
9. Loudspeaker                            10. Display brightness
                           
11. Monitor software                            12. Content of the service 
log
                           
13. Voltages                            14. Watchdog circuitry
                           
15. Alarm LEDs                            16. Membrane keys
                           
17. ComWheel                            18. Module 
communication
                           
19. Batteries                            20. Battery operation
                           
21. Battery charging                             
						

							Datex-Ohmeda S/5 FM
2(4)
Document no. M1187335-004
Recorder unit
     OK           N.A.          Fail
22. Recorder messages                            23. Recording
                           
24. Paper speed                            25. Quality of recording
                           
Notes
 
 
MemCard Option S/N
       OK           N.A.          Fail      OK           N.A.          Fail
26. Module recognition                            27. Memories and PCMCIA 
controller
                           
28. Communication                            29. Data Card recognition
                           
30. Menu Card recognition                            31. Menu card function
                           
                                                       
Notes
 
 
 
Network Option S/N
       OK           N.A.          Fail      OK           N.A.          Fail
32. Connection to network                            33. Ethernet address
                           
34. Data error counters                            35. Hardware error 
counters
                           
36. Disconnection 
recognition                            37. ID-plug recognition
                           
                                                       
Notes
  
						

							Appendix A Service check form, Datex-Ohmeda S/5 Frame for FM, F-FM
3(4)
                           Document no. M1187335-004
Wireless LAN option  S/N
      OK           N.A.          Fail      OK           N.A.          Fail
38. Signal strength                            39. Configure access point
                           
40. Connection to 
Network                                                        
Notes
 
 
General 
 
      OK           N.A.          Fail      OK           N.A.          Fail
41. Trends retaining                            42. Battery capacity
                           
43. Service Log reset                            44. Electrical safety check
                           
45. Final cleaning                            46. Fill in all necessary 
documents
                           
Notes
 
 
Used spare parts 
Signature   
						

							Datex-Ohmeda S/5 FM
4(4)
Document no. M1187335-004
For your notes: