GE Logiq 7 Service Manual

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-4 - Completing the Installation 3-13
3-4-2 Optional Peripherals/Peripheral Connection (cont’d)
Check if the fixing belts are loosen. If it is, tighten the belts again to secure the peripheral(s). If 
necessary, remove the peripheral from the device room to tighten the belts.
3-4-2-1 Approved on-board peripherals Refer to Section 5-3 Peripheral Compatibility .
Figure 3-6   How to Hold Peripherals
Belts
Belts BeltsConnect the related cables 
between the peripheral and 
LOGIQ 7 if they are NOT con-
nected each other. 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-14Section 3-4 - Completing the Installation
3-4-2-1 Approved on-board peripherals  (cont’d)
Connecting Cables
3-4-2-2 Reference off-board peripherals and options None.
CAUTIONEquipment damage possibility. Be sure to use the following recommended connecting cables to connect 
recording devices and a network with LOGIQ™ 7 console.
Table 3-4   List of Connecting Cables
NamePart No.FigureNOTE
Power Supply Cable P9509EE Connected to power
USB Serial Bridge  Cable 2304621 For converting the signal of 
RS232C cable to USB cable:
connected to VCR1 on the Rear 
Panel
AV Cable 2119874 Connected to Video-In/Out on the 
Rear Panel
The followings are the cables fo r BT04 ore lower system ONLY.
Mini-Plug Cable P9509BE Shutter control signals:
connected to B/W Printer
RS232C Cable  Cross 2305550
For control signals:
connected to Serial Bridge Cable
RS232C Cable  Straight 2305549
For control signals:
connected to Serial Bridge Cable
BNC Cable 2297053 For control signal:
connected to Composite B/W
USB Cable 2324360 Connected to USB port.
SCSI cables
(UP-D50 ONLY) 2375479
Connected toSCSI port and SCSI 
Cable Connector. 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-4 - Completing the Installation 3-15
3-4-3 Available Probes
See in specification in the LOGIQ™ 7 Reference Manual for Probes and intended use.
See Chapter 9 - Renewal Parts for Part Numbers to be used when ordering new or replacement probes.
Table 3-5   List of Transducers supported (All models)
Probe Name
Material of 
Headshell
Area of UsingTYPECatalog NumberPart Number
3C PESABDOMINAL CONVEX H79802P
H40412LB 2286353
2286354
5C PESABDOMINAL CONVEX H79822P
H40412LA 2294515
2294516
8C PBT NEONATAL
PEDIATRICS MICRO-CONVEX
H79792P
H40412LJ 2348093
2348094
E8C NORYL
PBT TRANSVAGINAL MICRO-CONVEX H79852P
H40412LE 2294640
2294641
M7C PBTABDOMINAL CONVEXH79832P
H40412LC 2294513
2294514
M12L PBTSMALL PARTS LINEARH79842P
H40412LD 2294510
2294511
7L NORYL ABDOMINAL
SUPERFICIAL LINEAR
H79862P
H40412LF 2294520
2294521
10L NORYL SUPERFICIAL LINEARH79872P
H40412LG 2294522
2294523
10S ABSPEDIATRIC SECTORH79922P
H4901PC 2309478
2298589
3.5C NORYL ABDOMINAL CONVEXH79812P
H4901PE 2303215
2050357
3.5CS NORYL ABDOMINAL CONVEXH78042P
H40412LK 2380854
2051858
3S NORYL CARDIOLOGY SECTORH79632P
H4701SZ 2348878
2323337
i12L ABSINTRAOPERATIVE LINEARH79322P
H4012L  2270556
2264883
M3S PBTCARDIOLOGY SECTORH79892P
H45011SZ 2293726
2378099
6T-OR-TEE PU: PolyUrethane TRASOPHAGEAL FOR 
ADULT
CARDIOLOGY SECTOR
H79932P
H45521DX 5131947
KN100068
7S PBTCARDIOLOGY SECTORH78082P
H40422LB 2355698
2347471
BE9C PBTTRANSRECTAL MICRO-CONVEX
H40412LW2389381
2389382
T739 NORYLINTRAOPERATIVE LINEARH76572SR
H40212LM2259245
2259246
4D3C_L PBTABDOMINAL CONVEX Volume H44801G 5121652
KTZ195893 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-16Section 3-4 - Completing the Installation
NOTE: PES: Polyethersulfone NORYL: Modified Polyphenylene Oxide PU: Polyurethane
PBT: Polybutylene Terephthalate ABS: Acrylonitrile Butadiene Styrene
NOTE: Some probes indicated on the table above have two different part numbers. The upper row  shows the part numbers of probes for Japan. The lower row shows the part numbers of probes 
for regions other than Japan. Probes which have only one part number are not available in 
Japan.
The following transducers, additional to ones listed in Table  3-6, are supported by V65x and later LOGIQ 
7 models.
The following transducers, additional to ones listed in Table 3-7 , are supported by R7.5.x and later 
LOGIQ 7 models.
The following transducers, additional to ones listed in Table 3-8 , are supported by BT09 and later 
LOGIQ 7 models.
4D10L PBDSUPERFICIAL LINEAR Volume H44801GB 5121651
KTZ156836
4C PBTABDOMINAL CONVEXH4904PC5131944
5123455
12L NorylSUPERFICIAL LINEARH40412LH2295375
2295377
P2D ABSCARDIOLOGY CWDH4830JETE100024
P6D ---SUPERFICIAL CWDH4830JGTQ100002
Table 3-6   List of Transducers supported by V65x and later 
Probe Name
Material of 
Headshell
Area of UsingTYPECatalog NumberPart Number
9L PBTVASCULAR SMALL 
PARTS LINEAR
H40412LT5131433
4DE7C PBTOB Gyn Urology CONVEX Volume H44801GA 5121650
Table 3-7   List of Transducers supported by R7.5.x and later 
Probe Name
Material of 
Headshell
Area of UsingTYPECatalog NumberPart Number
3CRF PU: PolyUrethane ABDOMINALMICRO-CONVEX H40442LP 5214820
5196216
Table 3-8   List of Transducers supported by BT09 and later 
Probe Name
Material of 
Headshell
Area of UsingTYPECatalog NumberPart Number
11L PBTSUPERFICIAL LINEARH78842P
H40412LY 5251881
5171885
Table 3-5   List of Transducers supported (All models)
Probe Name
Material of 
Headshell
Area of UsingTYPECatalog NumberPart Number 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-4 - Completing the Installation 3-17
3-4-4 Video Specification
3-4-5 Software Option Configuration
3-4-5-1 Onsite check and configuration
Select Utility > Admin > System Admin  and check the option software to be installed.
Table 3-9   Video Specifications
CRTLCD
Timing Parameter
800x600
75Hz
Timing Parameter
1280 x 1024 60Hz
Horizontal Rate [kHz] 46.88Horizontal Rate [kHz] 64
Horizontal Period [ µs] 21.33 Horizontal Period [µs] 15.625
Pixel Clock [MHz] 49.50Pixel Clock [MHz] 108
H Blank Width  [µs] 5.17 H Blank Width [µs] 3.778 (408dots)
H Sync Width  [µs] 1.62 H Sync Width [µs] 1.037 (112dots)
H Front Porch  [µs] 0.32 H Sync Front Porch [µs] 0.444 (48dots)
Active Horizontal Period  [µs] 16.16 Active Horizontal Period  [µs] 11.852 
(1280dots)
Vertical Rate [Hz] 75.00Vertical Rate [Hz] 60.0
Vertical Period [ms] 13.33Vertical Period [ms] 16.67 
(1066lines)
V Sync Width [lines=ms] 25=0.53V Sync Front Porch [ms] 0.016 (1 line)
V Front Porch  [lines=µs] 3=64.00 Equalization Porch None
Equalization Gate  [lines=µs] 1=21.3 Lines: Field/Frame 1066
Lines: Field/Frame 625Active Lines/Frame 1024
Active Lines/Frame 600 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-18Section 3-5 - Installation Paperwork
Section 3-5
Installation Paperwork
NOTE: During and after installation, the documentation (i.e. Users Manual, Installation Manuals...) for 
the peripheral units must be kept as part of the original system documentation. This will ensure 
that all relevant safety and user informations are available during the operation and service of 
the complete system.
3-5-1 Peripherals/Accessories Connector Panel
LOGIQ™ 7 peripherals and accessories can be properly connected using the rear connector panel 
located behind the rear door, front connector panel located next to the video printer, and Footswitch 
connector located bottom of the OP panel. 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-5 - Installation Paperwork 3-19
3-5-1-1 Rear Panel Connector
Located on the rear panel are video input and output connectors, audio input and output, camera 
expose connectors, footswitch connector power connector and control connections for VCR, printer, 
and service tools. 
This section indicates the pin assignment for each connector.
Figure 3-7   Rear Pannel Connector (BT04 or later)
Video In
Rec/Expose
VGA
S-Video
Out
S-Video
In
CmpstOut
Insite Audio
In
LR
LR
AudioOut
Ethernet
VCR2 VCR1 Service
CameraB/W
Color B/W
Color
Video Out
Power
AC Line Input
1200VA
220-240V
Circuit
Breaker
Circuit
Breaker
50 /60Hz
Power
AC Line Input
1200VA
50 /60Hz
100-120V
Circuit
Breaker
Circuit
Breaker
100-120V  350VA Max
Rear Pannel Connector for BT04 and later models
5
6
87
2
3
1 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-20Section 3-5 - Installation Paperwork
3-5-1-1 Rear Panel Connector (cont’d)
NOTE: Each outer (case) ground line of peripheral/accessory connectors are protectively grounded.  Signal ground lines are not isolated, except the Service port (3). All of signal lines (include signal 
GND) of the Service port are isolated.
The specified peripherals/accessories only can be connected to the USB ports.Rear Pannel Connector for BT03 or lower
Figure 3-8 Rear Panel Connector (BT03 or lower)


USB1.1 (USB compatible) 
or (USB + USB Serial Bridge 
+ RS232C)
(Reserved for future use)
2
1
3
4
5
6
87
USB1.1 (USB compatible) 
or (USB + USB Serial Bridge 
+ RS232C)
USB1.1 (USB compatible) 
or (USB + USB Serial Bridge 
+ RS232C) 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 3-5 - Installation Paperwork 3-21
3-5-1-1 Rear Panel Connector (cont’d)
Pin Assignment of S-Video Connector Connector: S-Terminal, 4-pin
Pin Assignment of VGA Connector Connector: Shrank D-Sub, 15-pin
Pin Assignment of Service/VCR 1/VCR 2 Connector, USB1.1 Connector: 4 pin Table 3-10   Pin Assignment of S-Video Connector
Pin No Output/Input Signal Description
1SVIDEO OUT/IN YG Y (Luma) GND
2 SVIDEO OUT/IN CG C (Chroma) GND
3 SVIDEO OUT/IN Y Y (Luma) SIGNAL
4 SVIDEO OUT/IN C C (Chroma) SIGNAL
Table 3-11   Pin Assignment of VGA Connector
Pin NoOutput Signal Description
1IO VGA OUT1 R Red
2 IO VGA OUT1 G Green
3 IO VGA OUT1 B Blue
6 IO VGA OUT1 RG Reg GND
7 IO VGA OUT1 GG Green GND
8 IO VGA OUT1 BG Blue GND
13 IO VGA OUT1 HS H Sync
14 IO VGA OUT1 VS V Sync
Others GND GND
Table 3-12   Pin Assignment of Service/VCR 1/VCR 2 Connector
Pin NoOutput Signal Description
1VBUSn Power Supply
2 Dn Data (-)
3 Dn Data (+)
4 GNDn Power Ground
1
24
3
1
2
 1
 6
 115 
10 
15 
3
1  2  3  4 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
3-22Section 3-5 - Installation Paperwork
3-5-1-1 Rear Panel Connector (cont’d)
Pin Assignment of Digital Int. Connector Connector: 6-pin
Pin Assignment of Ethernet Connector: RJ-45 Modular, 8-pin
Pin Assignment of Insite Connector: RJ-11 Modular, 6-pin Table 3-13   Pin Assignmen t of IEEE-1394 Connector)
Pin NoOutput Signal Description
1VP 1394 Power Supply
2 VG 1394 Power Ground
3 TPB 1394 Data B (-)
4 TPB 1394 Data B (+)
5 TPA 1394 Data A (-)
6 TPA 1394 Data A (+)
Table 3-14   Pin Assignment of Ethernet Connector
Pin NoOutput Signal Description
1ETHER TD Ethernet TD+
2 ETHER TD Ethernet TD-
3 ETHER RD Ethernet RD+
6 ETHER RD Ethernet RD-
Others NC Non-connection
Table 3-15   Pin Assignment of Insite Connector
Pin NoOutput Signal Description
2TEL L4 Telephone L4
3 TEL L2 Telephone L2
4 TEL L1 Telephone L1
5 TEL L3 Telephone L3
Others NC Non-connection
4
1  3  5 2  4  6
5
 8 1
6
 8 1