GE Logiq 7 Service Manual

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later) 8-35
8-2-10-2 Confirmation of the software version (cont’d)
2.) Touch the  System button on the Touch Panel.
3.) Click on  About tab. The software version will be shown on the monitor as shown. Confirm the 
following:
- Software Version ( R
8.x.x)
- Preset Resion (Americas, Europe, Asia, Japan, or None)
- Image Part Number (described on the Base System Software Image DVD) Figure 8-92   System
Figure 8-93   About Tab Press System
button.
Click on the About tab
Software Version
R 8.x..x
Base System Software CD-ROM
Part Number
xxxxxxx
Preset Region
(See 8-2-10-10 
Regional Preset.) 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
8-36Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later)
8-2-10-3 Computer Name and Connection Settings
1.) Touch Utility > Connectivity.
2.) Click on TCP/IP.
3.) Type  Computer Name.
4.) Verify that Enable DHCP  has no check mark. If checked, remove the mark.
5.) Check if Computer name, IP Address, Subnet Mask, and Default Gateway  are proper ones 
which you wrote down in section 8-2-6-4, Saving Connectivity.
6.) Click on  OK for confirmation dialog box.
NOTICEThe computer name is unique. Check the scanner serial Number printed on the label located at the rear 
lower side of the scanner. When 123456YM1 (for example) is printed,  L7-123456YM1 must be entered 
as a computer name.
Figure 8-94   TCP/IP
NOTICEIf the “Save settings” is NOT performed, you can NOT enter the new patient screen!! Figure 8-95   OK 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later) 8-37
8-2-10-3 Computer Name and Connection Settings (cont’d)
7.) Touch  Scan on the Touch Panel to return to the scan screen.
8.) Shut down the scanner.
9.) Power ON the scanner, then press  Patient key and verify that the following screen appears.
Figure 8-96   Patient  
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
8-38Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later)
8-2-10-4 Check LCD Monitor Hardware Setting
For 19 inch Monitor
To adjust the brightness:
1.) Press the Toggle button (2) or (3)  Once for brightness adjustment.
a.) Verify that Brightness is  80 (Dark Room) or 100 (Bright Room) .
If it is not, increase brightness to press the adjustment button (3).
If it is not, decrease brightness to press the adjustment button (2).
b.) Press the button (1) Once. The brightness display disappears.
NOTE: 19 inch LCD is ONLY a brightness adjustment.
8-2-10-5 Software Option Check 1.) Touch Utility > Admin.
2.) Click on System Admin  tab and verify that HW Number  is the same as the Option Dongle ID.
Figure 8-97   19 inch LCD Monitor Adjustment buttons
Figure 8-98   HW Number
123 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later) 8-39
8-2-10-6 VCR  Parameters Setting (for the VCR-equipped system ONLY)
1.) Touch Utility > System.
2.) Click on Peripherals  tab.
3.) Set the proper parameters: -PAL or NTSC
- VCR type
4.) Shut down the scanner, then restart the scanner.
5.) Verify that the VCR can be properly operated with no error (remote, play...) .
8-2-10-7 Regional Setup (For the system with language other than English ONLY) For Japanese Languages
You can set up the keyboard for Japanese. If you select Japanese, the following items display or enter 
by Japanese.
• Patient name
• Exam comment in Patient screen and Worksheet
• Report/Direct Report free text, Insert Text
• Annotation, Annotation Library
• Error/Warning message
• DICOM/Worklist, Query/Retrieve, Image Storage, Printer, MPPS Figure 8-99   Peripherals 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
8-40Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later)
8-2-10-7 Regional Setup (For the system with language other than English ONLY)  (cont’d)
1.) Select Utility> System> General>Regional Option Menu ,
2.) Click on  Languages tab.
3.) Check  Install files for East Asian languages.
4.) Click on  Apply.
5.) The system requires the re-boot automatically, shut down the system.
Figure 8-100   Regional Option
NOTICEYou do not need to change “Language used in menus and dialogs” option. It should be  English.
Check
Do not
Change
English. 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later) 8-41
8-2-10-7 Regional Setup (For the system with language other than English ONLY)  (cont’d)
6.) In  Utility> System> General , set the Language as JPN. Save this setting, but do not reboot the 
system yet.
7.) Press  Regional Options , under Standards and Formats select  Japanese, under Location select 
Japan . Press Apply .Figure 8-101   General
Figure 8-102   Regional Options 
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
8-42Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later)
8-2-10-7 Regional Setup (For the system with language other than English ONLY)  (cont’d)
8.) Select the Language tab , press Details, under Installed Services select the Japanese keyboard , 
under Default input language select  Japanese, press Apply , Press OK.
9.) Select the  Advanced tab , then select Japanese in the Language for non-Unicode programs pull-
down menu. Press Apply . Answer Yes to use files already loaded on the hard disk, then answer 
No  to not reboot the system yet, press OK . Press Save and Exit the Utility screen. 
10.) Reboot the system.
11.) In  Utility--> System--> General , press Regional Options. Select Language Tab  and press 
Details . Remove English  under Installed Services and press  Apply and OK.
12.) Select  Utility--> System--> About-->Additional Info menu .
Figure 8-103   Language tab
NOTICETo have the settings take effect, you MUST turn off the system and turn it back on.  
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later) 8-43
8-2-10-7 Regional Setup (For the system with language other than English ONLY)  (cont’d)
13.) Select  Automatic Setup for Japanese Language  button. Then IME configuration shall be 
automatically done.
This configuration shall setup the keyboard assignment (remove  
R
						

							GE HEALTHCARE
DIRECTION 2286865, REVISION 14LOGIQ™ 7 SERVICE MANUAL
8-44Section 8-2 - Software Loading Procedures for BT09 (R8.x.x or later)
8-2-10-7 Regional Setup (For the system with language other than English ONLY)  (cont’d)
For Russian or Greek Languages
1.) In  Utility--> System--> General , set the Language as Russian or Greek. Save this setting, but do 
not reboot the system yet.
2.) Press  Regional Options , under Standards and Formats select  Russian or Greek, under Location 
select  Russia or Greece . Press Apply.
3.) Select the  Language tab, press Details , under Installed Services select the  Russian or Greek 
keyboard , under Default input language select  Russian - Russian or Greek - Greek , press Apply, 
Press  OK. Figure 8-105   General
Figure 8-106   Regional Options