Dell 1100MP Projector Owners Manual
Have a look at the manual Dell 1100MP Projector Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Using Your Projector21 Language Menu Press the or button on the control panel or the or button on the remote control to select the preferred language for the OSD. Presss the on the control panel or the Menu button on the remote control to confirm the language selection. Factory Reset Menu Select Ye s to reset the projector to its factory default settings. Reset items include both computer image and video image settings. Computer Image Menu NOTE: This menu is only availabl e connected to a computer. F REQUENCY— Change the display data clock frequency to match the frequency of your computer graphics card. If you see a vertical flickering bar, use Frequency control to minimize the bars. This is a coarse adjustment. T RACKING— Synchronize the phase of the display signal with the graphics card. If you experience an unstable or flickering image, use the Tracking to correct it. This is a fine adjustment. NOTE: Adjust the Frequency first and then the Tracking.
www.dell.com | support.dell.com 22Using Your Projector HOR. POSITION—Press the button on the control panel or the button on the remote control to adjust the horizontal posi tion of the image to the left and press the button the control panel or the button on the remote control to adjust the horizontal position of the image to the right. VER. POSITION—Press the button on the control panel or the button on the remote control to adjust the vertical po sition of the image down and press the button the control panel or the button on the remote contr ol to adjust the vertical position of the image up. Video Image Menu NOTE: This menu is only available with S-video, Video (composite) signal connected. S ATURATION—Press the button on the control panel or the button on the remote control to decrease the amount of color in the image and press the button the control panel or the button on the remote control to increase the amount of color in the image. S HARPNESS—Press the button on the control panel or the button on the remote control to decrease the sharpness and press the button the control panel or the button on the remote control to increase the sharpness. TINT— Press the button on the control panel or the button on the remote control to increase the amount of green in the image and press the button the control panel or the button on the remote control to increase the amount of red in the image.
Troubleshooting Your Projector23 Troubleshooting Your Projector If you experience problems with your pr ojector, see the following troubleshooting tips. If the problem persists, contact Dell. Problem Possible Solution No image appears on the screen Ensure that the lens cap is removed and the projector turned on. Ensure the external graphics port is enabled. If you are using a Dell portable computer, press . For other computers, see your documentation. NOTE: Allow the projector some time to search for the source. Ensure that all the cables are securely connected. See Connecting Your Projector on page 7. Ensure that the pins of the connectors are not bent or broken. Ensure that the lamp is securely installed (see Changing the Lamp on page 26). Run Self-diagnostic test. See Self-diagnostic for Video on page 25. Ensure that the colors of the test pattern are correct.
www.dell.com | support.dell.com 24Troubleshooting Your Projector Partial, scrolling, or incorrectly displayed image1Press the Resync button on the remote control or the control panel. 2If you are using a Dell portable computer, set the resolution of the computer to XGA (1024 x 768): aRight-click the unused portion of your Windows desktop, click Properties and then select Settings tab. bVerify the setting is 1024 x 768 pixels for the external monitor port. cPress . If you experience difficulty in changing resolutions or your monitor freezes, restart all the equipment and the projector. If you are not using a Dell portable, see your documentation. The screen does not display your presentation If you are using a Dell portable computer, press . Image is unstable or flickering A djust the tracking in the OSD Computer Image tab. Image has vertical flicering bar Adjust the frequency in the OSD Computer Image tab. Image color is not correct If your graphic card output signal is sync on Green, and you would like to display VGA at 60Hz signal, please go into the OSD select Management, select Signal Type, and then select RGB. Run the Self-diagnostic test (see Self- diagnostic for video ) for preliminary diagnostic on image color problem. Ensure that the colors of the test pattern are correct. Image is out of focus1Adjust the focus ring on the projector lens. 2Ensure that the projection screen is within the required distance from the projector (3.9ft [1.2m] to 32.8ft [10m]). Problem (continued) Possible Solution (continued)
Troubleshooting Your Projector25 Self-diagnostic for Video Dell 1100MP Projector provides self-diagnost ic test of the projector video display (for Video, S-video, Component-i). Use thi s advanced feature for preliminary self- diagnostic on your projector when en countering a display problem for video. 1After turning on the projector, press the and buttons on the control panel simultaneously and release the bu ttons when screen goes blank. 2Press the and buttons again to exit the diagnostic mode. 3While in Self-diagnostic mode, the screen will run a seven-color-cycle test as following: Red Green Blue White Watchet Blue Dark Green Yellow. Ensure that the colors of the test pattern are correct. Contact Dell if the colors are not displayed correctly. The image is streched when displaying a 16:9 DVD The projector automatically detects 16:9 DVD and adjusts the aspect ratio to full screen with a 4:3 (letter-box) default setting. If the image is still stretched, adjust the aspect ratio as follows: If you are playing a 16:9 DVD, select 4:3 aspect ratio type on your DVD player (if capable). If you cannot select 4:3 aspect ratio type on your DVD player, select 4:3 aspect ratio in the All Images menu in the OSD. Image is reversed Select Management from the OSD and adjust the projecton mode. Lamp is burned out of makes a popping sound When the lamp reaches it s end of life, it may burn out and may make a loud popping sound. If this occurs, the projector does not turn back on, and displays Lamp Defective in the LCD display until the lamp is replaced. To replace the lamp, see Changing the Lamp on page 26. The remote control is not operating smoothly or in very limited range The battery may be low. If so, replace it with 2 new AAA batteries. Problem (continued) Possible Solution (continued)
www.dell.com | support.dell.com 26Troubleshooting Your Projector Changing the Lamp Replace the lamp when the message Lamp is approaching the end of its useful lif e. Replacement suggested! www.dell.com/lamps appears on the screen. If this problem persists after replacing the lamp, contact Dell. CAUTION: The lamp becomes very hot when in use. Do not attempt to replace the lamp until the projector has bee n allowed to cool down for at least 30 minutes. CAUTION: Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper handling, inc luding the touching of the bulb or the lamp glass. 1Turn off the projector and disconnect the power cord. 2Let the projector cool fo r at least 30 minutes. 3Loosen the 2 screws that secure the lamp cover, and remove the cover. 4Loosen the 2 screws that secure the lamp. 5Pull up the lamp by its metal handle. 6Reverse steps 1 through 5 to install the new lamp. the left Lamp Reset icon in the OSD Management tab. NOTE: Dell may require that lamps replaced under warr anty be returned to Dell. Otherwise, contact your local waste disposal agenc y for the address of the nearest deposit site. NOTE: The lamp contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. 7Reset the lamp usage time by selecting
Specifications27 Specifications 5 Light Valve Single-chip DLP™ DDR (double data rate) technology Brightness 1400 ANSI Lumens (Max) Contrast Ratio 2000:1 Typical (Full On/Full Off) Uniformity 80% Typical (Japan Standard - JBMA) Lamp 200-watt user-replaceable UHP 2000- hour lamp(up to 2500 hours in eco mode) Number of Pixels 800 x 600 (SVGA) Displayable Color 16.7M colors Color Wheel Speed 100~127.5Hz (2X) Projection Lens F/2.44~2.69, f=28.8~34.5mm with 1.2x manual zoom lens Projection Screen Size 27-275 inches (diagonal) Projection Distance 3.9~32.8 ft (1.2m~10m) Video Compatibility NTSC, NTSC 4.43, PAL, PAL-M, PAL- N, SECAM, and HDTV (1080i, 720P, 576i/P, 480i/P) compatibility Composite video, Component video and S-video capability H. Frequency 15kHz-70kHz (Analog) V. Frequency 43Hz-85Hz (Analog) Power Supply Universal 100-240V AC 50-60Hz with PFC input Power Consumption 250 Watts full power (typical), 200 Watts in eco mode
www.dell.com | support.dell.com 28Specifications Audio 1 speaker, 2 Watts RMS Noise Level 34dB(A) Full-on mode, 32dB(A) Eco-mode Weight 4.85 lbs (2.2 kgs) Dimensions (W x H x D) External 9.9 x 3.96 x 8.4 ± 0.04 inches (251 x 101 x 213 ± 1mm) Environmental Operating temperature: 0 oC–35oC (32oF–95oF) Humidity: 80% maximum Storage temperature: –20 oC to 60oC (–4oF to 140oF) Humidity: 80% maximum Regulatory FCC, CE, VCCI, UL, cUL, TüV- GS, ICES-003, MIC, C-Tick, GOST, CCC, PSB, NOM, TüV-S/Argentina I/O Connectors Power: AC power input socket Computer input: one D-sub for analog/component, HDTV input signals Computer output: one 15-pin D-sub Video input: one composite video RCA and one S-video USB input: one USB connector Audio input: one phone jack (diameter 3.5mm) One mini-DIN RS232 for wired remote projector control from PC
Specifications29 RS232 Pin Assignment RS232 Protocol Communication Settings Control command Syntax (From PC to Projector) [H][AC][SoP][CRC][ID][SoM][COMMAND] Example: power on the projector Enter the following code: 0xBE 0x EF 0x10 0x05 0x00 0xC7 0xBF 0x11 0x11 0x01 0x00 0x02 Connection settingsValue Baud Rate: 19200 Data Bits: 8 Parity None Stop Bits 1
www.dell.com | support.dell.com 30Specifications Control Commands List Control Commands List Address Code (BYTE)Size of the Pa y l o a d (WORD)CRC16 for the entire packet (WORD) MsG ID (WORD) MsG size (WORD)Command code (BYTE) Command Description 0xefbe 0x10 0x0005 0xffc6 0x1111 0x0001 0x01 Power 0xbfc7 0x02 Menu 0x7e07 0x03 Up 0x3fc5 0x04 Down 0xfe05 0x05 Left 0xbe04 0x06 Right 0x7fc4 0x07 Resync 0x3fc0 0x08 Source 0xfe00 0x09 Volume+ 0xbe01 0x0A Volume- 0xffc3 0x0D Mute 0xbfc2 0x0E Freeze 0x7e02 0x0F Hide 0x3fca 0x10 Video Mode 0x7fcb 0x13 V. Keystone Up 0x3e09 0x14 V. Keystone Down 0x7e08 0x17 Aspect ratio (4:3/16:9)