compaq contura 400 family User Manual
Have a look at the manual compaq contura 400 family User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 50
7. Open the battery compartment by lifting up the front of the computer [1]
and sliding the battery compartment release button to the right [2]. The
battery compartment opens slightly. Lower the compartment [3]
(Figure 3-3).](http://img.usermanuals.tech/thumb/1258/38919/w64_compaq-contura-400-family-49.png "Page 50
7. Open the battery compartment by lifting up the front of the computer [1]
and sliding the battery compartment release button to the right [2]. The
battery compartment opens slightly. Lower the compartment [3]
(Figure 3-3).")
2. Close the computer and turn it top-side down. 3. Move the tilt foot toward the front of the computer, exposing the handle bracket screw on either side of the computer (Figure 3-5). 4. Using a Torx T8 , remove the screw and washer from each handle bracket. These screws are not reusable and must be discarded. 5. Remove the handle bracket (Figure 3-6).
6. To install the handle bracket, reverse the previous steps. Discard the old screws and replace with new screws. Chapter 3.4 Tilt Feet This procedure is necessary if replacing the tilt feet or if separating the display assembly from the system unit module. Removing the Tilt Feet To remove the tilt feet, follow these steps: 1. Disconnect all power from the computer and remove the AC Adapter and battery pack (Section 3.2). 2. Using a Torx T8 , remove the tilt foot screw (Figure 3-7). Screws from the tilt feet are not reusable and must be discarded. 3. Remove the tilt foot (Figure 3-7).
4. To install the tilt foot, reverse the previous steps. Discard the old screws and replace with new screws. Chapter 3.5 Hard Drive This section contains removal procedures for the following hard drive components: o Hard drive compartment cover o Hard drive o Hard drive bracket Removing the Hard Drive Compartment Cover To remove the hard drive compartment cover, follow these steps: 1. Disconnect all power from the computer and remove the battery pack, diskette, and PC Card, if installed (Section 3.2).
2. Close the computer and turn it top-side down. 3. Using a Torx T-8 or flat-bladed screwdriver, remove the two screws from the hard drive compartment cover (Figure 3-8). NOTE: These two screws also secure the CPU base to the keyboard and must be removed in order to remove the keyboard and access system components. 4. Use a Case utility tool to remove the hard drive compartment cover (Figure 3-9).
5. To replace the hard drive compartment cover, reverse the previous steps making sure to insert the brackets tab under the plastic edge. Removing the Hard Drive 1. Remove the hard drive compartment cover. Refer to Removing the Hard Drive Compartment Cover in this section. 2. Remove the hard drive by grasping the hard drive bracket and sliding it toward the front of the computer [1] (Figure 3-10). 3. Lift the hard drive and bracket [2] up and out of the computer (Figure 3-10).
4. To replace the hard drive, reverse the previous steps. Removing the Hard Drive Bracket 1. Remove the hard drive compartment cover. Refer to Removing the Hard Drive Compartment Cover in this section. 2. Remove the hard drive and bracket. Refer to Removing the Hard Drive in this section. 3. Using a Torx T8 , remove the four screws from the hard drive bracket and separate the bracket from the hard drive (Figure 3-11).
4. To replace the hard drive bracket, reverse the previous steps. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
Chapter 3.6 Memory Expansion Board This section contains removal and replacement procedures for the memory compartment cover and the memory expansion board. The memory compartment cover and the bottom of the CPU base are embossed with arrows and two icons that indicate whether the memory compartment cover is unlocked [1] or locked [2].