compaq contura 400 family User Manual
Have a look at the manual compaq contura 400 family User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 211
7. Connect the display cable and the backlight cable to the inverter
board (Section 3.25).
8. Replace the inverter board (Section 3.25).
9. Replace the bezel (Section 3.25).
10. Connect the display ground cable [1] from the LIF clip above the serial
port connector (Figure 3-156).](http://img.usermanuals.tech/thumb/1258/38919/w64_compaq-contura-400-family-210.png "Page 211
7. Connect the display cable and the backlight cable to the inverter
board (Section 3.25).
8. Replace the inverter board (Section 3.25).
9. Replace the bezel (Section 3.25).
10. Connect the display ground cable [1] from the LIF clip above the serial
port connector (Figure 3-156).")
7. Connect the display cable and the backlight cable to the inverter board (Section 3.25). 8. Replace the inverter board (Section 3.25). 9. Replace the bezel (Section 3.25). 10. Connect the display ground cable [1] from the LIF clip above the serial port connector (Figure 3-156).
11. Carefully insert the end of the display ground cable into the ZIF connector slide on the system board. IMPORTANT: Ensure that the ZIF connector slide is in its fully upward position and that it remains so while you are inserting the cable into it. Before closing the slide, ensure that the cable is fully seated (to the white insertion line) in the ZIF connector. 12. While holding the end of the display cable inside the ZIF connector slide, press down both ends of the slide simultaneously to secure the cable in the ZIF connector (Figure 3-157).
13. Ensure that the cable has been seated evenly and that the white line on the cable is level. 14. Replace the keyboard assembly (Section 3.7). Chapter 3.27 Color TFT (10.4 inch) Display (Models 420 and 430) IMPORTANT: The Monochrome, CSTN and the CTFT displays have different removal and replacement procedures. Be sure to follow the procedures for the specific display. This sections contains removal and replacement procedures for the following CTFT (10.4 inch) display components: o Display panel o Display cable o Shield o Display ground cable
Removing the CTFT Display Panel To remove the CTFT (10.4 inch) panel, follow these steps: 1. Disconnect all power from the computer and remove the AC Adapter and battery pack (Section 3.2). 2. Open the computer. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>>
NOTE: The CTFT (10.4 inch) display is different than all other displays. The inverter board fits partially behind the display. Loosen the screws on the display to slide the inverter out from behind the display. 5. Remove the inverter board (Section 3.25). 6. Remove the display cable and backlight cable from the inverter board (Section 3.25). 7. Remove the four screws that secure the CTFT (10.4 inch) panel to the display enclosure (Figure 3-159).
8. Carefully rotate the CTFT (10.4 inch) panel down and out of the display enclosure, laying the CTFT (10.4 inch) panel gently on the keyboard assembly (Figure 3-160).
9. Remove the display cable from the connector on the back of the panel (Figure 3-161).
10. The CTFT Display Cable is disconnected by pulling upward on the tabs on the back of the Connector. Replacing the CTFT (10.4 inch) Display Panel >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
2. Position the CTFT (10.4 inch) panel into the display enclosure, ensuring that the ZIF connector end of the display cable is exposed on the right side of the CTFT (10.4 inch) panel (Figure 3-163).
3. Secure the CTFT (10.4 inch) panel with four screws to the display enclosure. Removing the CTFT (10.4 inch) Display Cable To remove the CTFT (10.4 inch) display cable, follow these steps: 1. Disconnect all power from the computer and remove the AC Adapter and battery pack (Section 3.2). 2. Open the computer. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>