compaq contura 400 family User Manual
Have a look at the manual compaq contura 400 family User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 238
30. Connect the display ground cable [1] to the LIF clip above the serial
port connector between the system board and the system chassis
(Figure 3-181).](http://img.usermanuals.tech/thumb/1258/38919/w64_compaq-contura-400-family-237.png "Page 238
30. Connect the display ground cable [1] to the LIF clip above the serial
port connector between the system board and the system chassis
(Figure 3-181).")
![Page 244
5. Remove the left and right clutch ground clips (see Removing and
Replacing Clutch Ground Clips in this section).
6. Pull up both ends of the ZIF connector slide simultaneously [1],
carefully opening the slide [2] (Figure 3-186).
7. Lift the display cable out of the connector slide [3], being careful
not to pull or twist the cable (Figure 3-186).
8. Remove the display ground cable [1] away from the LIF clip
(Figure 3-187).](http://img.usermanuals.tech/thumb/1258/38919/w64_compaq-contura-400-family-243.png "Page 244
5. Remove the left and right clutch ground clips (see Removing and
Replacing Clutch Ground Clips in this section).
6. Pull up both ends of the ZIF connector slide simultaneously [1],
carefully opening the slide [2] (Figure 3-186).
7. Lift the display cable out of the connector slide [3], being careful
not to pull or twist the cable (Figure 3-186).
8. Remove the display ground cable [1] away from the LIF clip
(Figure 3-187).")
35. Replace the keyboard assembly (Section 3.7). 36. Replace the tilt feet (Section 3.4). 37. Replace the handle bracket (Section 3.3). Chapter 3.29 Clutches and Ground Clips This section contains removal and replacement procedures for the clutch ground clips located between the system chassis and CPU base, and for the clutches that join the system unit module and the display enclosure. Removing and Replacing the Clutch Ground Clips To remove the left and right clutch ground clips, follow these steps: 1. Disconnect all power from the computer and remove the AC Adapter and battery pack (Section 3.2). 2. Remove the keyboard assembly (Section 3.7). 3. Remove the left clutch ground clip from the system chassis (Figure 3-184).
4. Remove the right clutch ground clip located between the clutch and the CPU base. The right clutch clip for Models 420 and 430 is different and is illustrated in the insert (Figure 3-185).
5. To replace the clutch ground clips, reverse the previous steps. Removing and Replacing the Clutches To remove the clutches, follow these steps: 1. Disconnect all power from the computer and remove the AC Adapter and battery pack (Section 3.2). 2. Remove the handle brackets from each side of the computer (Section 3.3). 3. Remove the tilt feet from each side of the computer (Section 3.4). >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
5. Remove the left and right clutch ground clips (see Removing and Replacing Clutch Ground Clips in this section). 6. Pull up both ends of the ZIF connector slide simultaneously [1], carefully opening the slide [2] (Figure 3-186). 7. Lift the display cable out of the connector slide [3], being careful not to pull or twist the cable (Figure 3-186). 8. Remove the display ground cable [1] away from the LIF clip (Figure 3-187).
9. Using a Torx T8 or slotted driver, remove the four clutch screws on the rear of the system unit module (Figure 3-188).
10. Lift the display assembly off the system unit module (Figure 3-189).
11. Place the display assembly top-side up. 12. Remove the display bezel (Section 3.21). 13. Remove the screws from the clutches on either side of the display enclosure. 14. On either side of the display enclosure, slide the clutches from underneath the display shield tabs (Figure 3-190).
15. Slide the clutches out of the display enclosure. 16. To replace the clutches, reverse the previous steps. IMPORTANT: When replacing the display clutch screws, ensure proper alignment of the display clutches on either side of the display enclosure with the shield (Figure 3-191).
Chapter 3.30 Docking Base This section contains removal procedures for the following docking base components: o Battery Door o Feet o Handle Removing the Battery Door To remove the battery door, follow these steps: 1. Open the battery door until it is perpendicular to the docking base (Figure 3-192).
2. Hold the door upright, applying pressure to the door at the base of the front hinge [1]. This creates a pivot point [2] to rotate the door out of the base (Figure 3-193). 3. Flex the front end of the door until the retaining pin [3] clears the hinge slot on the docking base (Figure 3-193).