ATT System 25 Installation And Maintenance Manual

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
2053:incorrect entryArea Code = NPA
incorrect area code office
where N=2-9, P=0-l ,and A=l -9.
codeOffice Code = NXX where N=2-9,
X=0-9
Invalid area code or office code for
Toll Calls Allowed.
2054:incorrect entryData entry must be 0-2.
data must be 0-2
2055:inappropriate requestFound office code but not in proper
office code found in wronglist.
list
2056:incorrect entry
Area Code does not exist in the NPA
area code does not exist(no such area code found in table).
2057:incorrect entry
Specified office code pattern and list
incorrect area code officenot found in table) There are no office
codecodes for the given list under the area
code.
2060:action number out ofCheck the Administration Manual for
sequencecorrect ACTION sequence.
improper procedure
2062:
entry out of rangeCall Coverage Group out of range -
number out of rangetoo high.
2063:incorrect entryCall Coverage Group zero not
number can’t be 0allowed.
2066:incorrect facility type
Port not a station
must be station type
2067Invalid data, SLCNumber entered not in allowable
reprioritization 0-30 sec.range of time.
2068:incorrect PDCZero not allowed for station PDC.
station can’t have 0
2071:out of spaceNo more Universal Port Numbers
no more groups available(UPNs) available.
2072:action number out ofCheck Admin. manual for correct
rangeACTION number/sequence.
does not exist or used
improperly
2073:incorrect entryLIST ‘target’ is out of range.
list reference out of range
F-13 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
2074:inappropriate requestCheck Home Area Code/Toll Call
office code exists-list 1
Allowed list to see if office code exists
in list 1. Added office code to pattern
already.
2075:inappropriate request
Check Home Area Code/Toll Call
office code exists-list 2Allowed list to see if office code exists
in list 2. Added office code to pattern
already.
2076:inappropriate requestCheck Home Area Code/Toll Call
office code exists-list 3
Allowed list to see if office code exists
in list 3. Added office code to pattern
already.
2077:inappropriate requestCheck Home Area Code/Toll Call
office code exists-list4
Allowed list to see if office code exists
in list 4. Added office code to pattern
already.
2078:inappropriate request
See: MENU = 7 (TCA)
subset exists-list 1ACTION = 2
Trying to add a number to a TCA list
that already exists in another list.
2079:inappropriate request
See: MENU =7 (TCA)
subset exists-list 2ACTION =2
Trying to add a number to a TCA list
that already exists in another list.
2080:inappropriate request
See: Menu = 7 (TCA)
subset exists-list 3ACTION = 2
Trying to add a number to a TCA list
that already exists in another list.
2081:inappropriate request
See: MENU = 7 (TCA)
subset exists-list 4ACTION = 2
Trying to add a number to a TCA list
that already exists in another list.
F-14 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
2082:inappropriate request
See: MENU = 7 (TCA)
superset exists-list 1ACTION = 2
Trying to add a number to a TCA
list that already exists in another
list. In this case, the superset is
used in conjunction with wild card
characters.
2083:
inappropriate requestSee: Menu = 7 (TCA)
superset exists-list 2ACTION = 2
Trying to add a number to a TCA
list that already exists in another
list. In this case, the superset is
used in conjunction with wild card
characters.
2084:inappropriate requestSee: MENU = 7 (TCA)
superset exists-list3ACTION = 2
Trying to add a number to’s TCA
list that already exists in another
list. In this case, the superset is
used in conjunction with wild card
characters.
2085:
inappropriate requestSee: MENU = 7 (TCA)
superset exists-list4ACTION = 2
Trying to add a number to a TCA
list that already exists in another
list. In this case, the superset is
used in conjunction with wild card
characters.
2086:inappropriate requestIndividual Call Coverage Msg
button already assignedWaiting button has already been
added.
2087:inappropriate requestOption not allowed for given port.
not allowed for port-on-Recheck port options.
board
2088:incorrect entryValue out of range for selected
data out of rangeoption.
F-15 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
2089entry out of rangeARS Facility Level = O-3.
facility restriction level
exceeded
2090:inappropriate requestSingle line stations are defaulted
station not allowed speedpersonal speed dialing. ATL
numberstations must be administered
personal speed dialing.
3000:inappropriate request
Trunk is not a pool member;
trunk must be pooltherefore, this item cannot be
memberentered.
3001:incorrect entryTrunk directory number is not 4
number must be 4 digitsdigits.
3003:inappropriate request
Only DIDs can have the same trunk
non-DlD not allowednumber.
3005:inappropriate request
Check trunk number to see if it
trunk not installedexists. Trunk not installed; item
cannot be requested.
3007:incorrect entry
Entry for DID expected digits is only
can’t exceed 1 digit1.
3008:
entry out of rangeClass of service for DID must be 1-
DID digit must be value
4. Check ACTION = 3 under
from 1-4trunks.
3010:inappropriate requestThe maximum class of service type
number can’t exceed 4,is expected.
3011:inappropriate requestDial-in Tie trunks cannot receive
dial-in ties can’t haveservice treatment.
night service
3012:incorrect PDC
Must be numerical value. The
leading space not allowedentered number was determined by
the system to have a leading blank.
3013:inappropriate requestThe number was previously
already assigned toassigned to a nonpool facility.
nonpool facility
3014:inappropriate request
The trunk is the last one in the pool
last pool trunk: andand cannot be removed until the
dependent stationsstations with the pool buttons
pointing to this pool are eliminated.
F-16 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
I
AND DESCRIPTIONPOSSIBLE SOLUTION
3015:at installed maxCan install 16 trunk group
-pool groupsmaximum.
3016:
entry out of rangeOnly 1 digit can be entered for the
access code must be 1trunk pool dial access information.
digit
3017:
entry out of rangeThe maximum value that can be
access code can’t exceed
entered for trunk pool dial access of
11.
3018:
inappropriate requestThe hunting position of a trunk in
only display of hunt
pool cannot be updated manually.
position allowed
3019:incorrect entry
Can have 32 DGC groups with 20
DGC group number outmembers per group. The entered
of rangenumber is not in the range of
allowed DGC groups.
3021:inappropriate requestDID trunks are not assignable to
DID trunk can’t haveNS.
night service
3024:inappropriate requestCannot administer announcement
tie trunks not allowed
for TIE trunks.
announcement
3025:inappropriate request
The entered value is not a delay
announcement must beannouncement group number.
0-2
3026:inappropriate requestThe entered flexible night service
announcement machinedelay announcement machine group
not installeddoes not have an announcement
machine installed.
3027:
inappropriate requestTrunk cannot be removed until the
trunk has dependentpersonal trunk buttons pointing to it
buttonsare untranslated.
4000:incorrect action number
I
Recheck Action value taken.
must be 0-5.
F-17 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTION
POSSIBLE SOLUTION
4001:
entry out of rangeMaximum FPDCs = 300
FPDC max reached
4002:incorrect entry
Specified FPDC not found.
does not exist or used
improperly
4003:
action number out ofMust do action 1 before removing
sequenceFPDC.
do action 1 display before
FPDC removal
4005:
inappropriate request
CAP not installed even through flag
unlogged FPDC’s/non-
is set to send FPDCs not logged in
existent CAPthere.
4007:
incorrect action number
Action invalid for FPDC update or
can’t exceed 2 if FPDCdisplay.
update/display
4008:
inappropriate requestFacility unequipped for FPDC 
facility not equipped
display.
4014:at installed max -300Maximum FPDCs = 300
FPDCs
5003:incorrect entryNumber of seconds after last digit
data out of rangedialed to commence billing is
invalid.
5005:entry out of rangeNPA cannot exceed 3 digits.
area code can’t exceed 3
digits
5006:incorrect entry
Area Code= NPA where N=2-9,
area code digit out ofP=0-l, and A=1-9.
range
5007:incorrect entry
Date must be in the form
date must be 6 digits(MMDDYY).
5010:incorrect entryDate = MMDDYY where MM=01 -
incorrect month data12, DD=01 -31, and YY=00-99.
5011:incorrect entryDay = HHMM where HH=00-23,
incorrect day dataMM=00-59
5012:
entry out of range
Hours/minutes = HHMM (4 digits
hours/minutes must be 4
exactly)
digits
F-18 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
5013:incorrect entry
Day= HHMM where HH=00-23
incorrect hours data
5014:incorrect entryDay = HHMM where MM= 00-59
incorrect minutes data
6000:incorrect entryCheck search type in admin. manual
search type does notto see if it exists.
exist
6001:
incorrect action numberGo back and check action value
can’t exceed 1 digit
taken.
6003:
entry out of rangeSearch maximum reached.
search max reached
6004:
inappropriate requestMust enter search type. Check
must enter search typeAdmin. manual to verify.
6005:inappropriate requestCannot perform a search until all
must enter search dataACTION & DATA values have been
entered.
6007:
incorrect action numberAccepts only 1 or 2.
must be 1 or 2
6008:incorrect entry
No item #2 data expected for the
data not allowedsearch type given in item #1
6009:incorrect entryTraffic register number given in item
number out of range#2 is out of range.
6010:incorrect entry
Trunk number given in item #2 is
incorrect trunknot valid.
6011:
incorrect PDCThe number under item #2 is not
not optioned or usedacceptable. It should relate to
improperlyeither stations, DGCs, page-all or
paging zones.
6015:incorrect entryThe entered board type is unknown.
board type does not exist
F-19 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
6016:incorrect facility typeThe subtype number is the entered
subfacility type out of
type is too large for the facility
range
specified.
6017:incorrect entryTraffic register number given is out
number out of range
of range.
6018:incorrect action number
Item No. 3 is not applicable for the
incompatible with search
entered search type under item No.
1.
6020:incorrect action numberData entered for an item number is
can’t exceed 4 digitsgreater than 4 digits and is not
acceptable.
6021:incorrect entry
32 DGC groups/20 members per
DGC group number outgroup. Can only be a member of 1
of rangegroup at a time.
6022:
inappropriate requestCannot perform a search until the
must enter search data
data has been entered in item 3.
6023:incorrect entryThe entered alarm type is unknown.
type does not exist
6024:incorrect action number
Item No. 2 is not applicable for the
incompatible with searchentered search type under item No.
1.
6025:incorrect entryIncorrect pattern number or
illegal character withinunexpected wild card character.
dataSee:
MENU = 8 (Search)
ACTION = 1 DATA = 21 or
ACTION = 2 DATA = 1-8
for more information.
7003:incorrect entryData must be 1-31. See:
data must be 1-31MENU = 4 (System)
ACTION = 3 and ACTION = 7
for more information.
7004:incorrect entryData must be 0-31. See:
data must be 0-31MENU = 4 (System)
ACTION = 41
for more information.
F-20 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
7005:incorrect entryEntered data not valid for restricting
incorrect data to restrict
PBX calls.
PBX calls
7006:incorrect entryNumber of seconds before a
data can’t exceed 120
camped on call returns to the
attendant console [1-1 20].
7007:inappropriate request
To install CAP: Go to MENU 1 (Port)
must install CAP firstACTION = 1, DATA = terminal type
(309, or 310)
ACTION = 2, DATA = PDC
7008:inappropriate request
Cannot set bit for FPDCs to go to
must install CAP firstthe CAP because neither the
primary nor secondary CAP is
installed.
7010:out of spaceNumber plan is full.
no more room to change
7011:out of spaceID (Name) directory is full.
no more room to add
7012:inappropriate requestCheck to see if PDC already exists.
PDC already existsGo to MENU 8-Search
ACTION = 1 DATA = 11
Hit c to continue to search for
assigned PDCs
7016:incorrect entry
Data must be O-1. See:
data can’t exceed 1MENU = 4 (System)
ACTION = 5
for more information.
7017:incorrect entry
Data not valid for number of DID
must be 0 - 4digits used by PDCs.
7019:
PDC out of rangeSystem 25 dial codes may have
must be 1-9999
1,2,3 or 4 digits (1-9999).
7020:entry out of rangeData is greater than 2 digits.
data can’t exceed 2 digits
7021:incorrect entrySystem Maximum Account Code
account code can’tdigits (O-1 5). Default = 15
exceed 15 digits
F-21 
						

							APPENDIX F: Administration Error Messages
ERROR MESSAGE
AND DESCRIPTIONPOSSIBLE SOLUTION
7023:incorrect entryData value cannot exceed 1.
data can’t exceed 1
7026:
incorrect PDCMust be station or data port.
must be station or data
port
7027:incorrect entryEntry cannot be 0 or exceed 5
can’t be 0 or exceed 5
digits.
digits
7030:incorrect entryLeading 0 was found while
leading zeros not allowedprocessing item 2 for paging zone
add.
7031:
out of spaceNot enough room for adding new
no more room to addpaging zones.
7032:incorrect PDCEntered numbers for this zone and
this zone & all zoneall zone is ambiguous.
PDC’s do not agree
7034:action number out ofMust assign a paging zone before
sequence
trying to administer all zone paging.
must enter 2 first
7035:inappropriate requestThe paging zone is equipped;
paging zone nottherefore the restriction flag is
equippedunknown.
7036:incorrect button numberButton on station is previously
station button alreadyassigned.
exists