Home
>
Telrad Digital
>
Communications System
>
Telrad Digital Emagen Unified Messaging System Manual
Telrad Digital Emagen Unified Messaging System Manual
Here you can view all the pages of manual Telrad Digital Emagen Unified Messaging System Manual. The Telrad Digital manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 71
76-110-0887/0, Issue 1 5-8 Before backup, the system will notify you it is shutting down. 2. After the backup is complete, you will have to manually restart the system services. 5.4.6 System Monitor -- option 6 The system monitor will show you a real time info snapshot of all the system ports, as well as indication of the status of the serial link. You can use this option to start and stop each one of the voice ports, as well as perform a “soft” shutdown of the system, that is, wait until all...
Page 72
Section 5: SYSTEM ADMINISTRATION 5-9 5.4.11 Import/Export Data Base You can import or export a mailbox, class of service or department data base. You can then upload this information on a different ma- chine and put it back on the current system. Select the desired mailbox, COS or department. The system will request a floppy disk, or it will save it in a temporary location. 5.4.12 Select PBX emaGEN has a built in library of PBXs from which you can choose. 1. Simply select the PBX type and 2....
Page 73
76-110-0887/0, Issue 1 5-10 Enter the number of voice channels on the card. Enter the number of RDSP on the card (1 for every 4 ports). 4. Finally, confirm the information and repeat for each card. 5. Reboot the system after completion of this process. 5.4.14 Define modem 1. Select which com port will be used for remote administration. For Com1 press 1, Com2 press 2, etc. 2. Fax ports can be defined as remote administration ports when setting up fax ports, below. 5.4.15 Configure Fax Select the...
Page 74
Section 5: SYSTEM ADMINISTRATION 5-11 You can choose to enable or disable fax ports for remote administra- tion by modem. 5.4.16 Installing the Fax software In case step 1 of the previous section fails, that is you cannot run the fax setup option, follow the following procedure: 1. Log in as super user -- type: su -, followed by the root password. 2. Type: cd / emaGENinstall 3. Type: ./setup. This will run the emaGEN Installation procedure. 4. Press N on all options, until you reach the Install Fax...
Page 75
76-110-0887/0, Issue 1 5-12 You can run it while connected over an IP connection. Double click the emaGEN Monitor icon. You will be prompted for a host name. Enter the IP address of emaGEN. You will see the status of all ports. You can start or stop a port by right clicking the port. 5.6emaGEN CONTROLLER The emaGEN Controller Main Menu screen -- shown in Figure 5-3, below -- is the top of the pyramid of all administration configuration and definition screens. Figure 5-3 emaGEN Controller Main...
Page 76
Section 5: SYSTEM ADMINISTRATION 5-13 Figure 5-4 SMDR Reports definition screen To view information regarding a particular extensiion: fill in the Extension number field. To view information regarding a particular trunk: fill in the Trunk number field. 5.7.3 Costing of calls Cost per minute To generate price information, enter: either the cost per minute and/or
Page 77
76-110-0887/0, Issue 1 5-14 the surcharge per call. The cost per minute is calculated in one minute increments. For example: If the cost per minute is 15 cents and the call duration is 45 seconds, the call cost is 15 cents. If the call duration is 1 minute and 5 seconds, the call cost is 30 cents. Call cost If you entered information in the cost per minute section, above, you can select calls by cost according to the following criteria: Fill in only the from field -- to view calls equal or...
Page 80
6-1 Section 6 emaGEN WEB CONTROLLER 6.1 THE emaGEN WEB CONTROLLER MAIN MENU SCREEN Figure 6-1 emaGEN Web Controller Main Menu screen 6.2 THE emaGEN WEB CONTROLLER ADMINISTRATION UTILITY The emaGEN Web Controller screen is the administration utility of the emaGEN system. The emaGEN Web Controller is TCP-IP web-based, so you can use it locally or remotely over a network. 6.3 TO USE THE emaGEN WEB CONTROLLER 1. Open a browser 2. Type in the IP address of emaGEN