Telrad Digital Emagen Unified Messaging System Manual

76-110-0887/0, Issue 1
3-6
emaGEN, on one, two or three OCD cards;
 inserting the OCD card(s), with MIM(s) mounted, in the 
unite 
system cabinet.
 Connection between 
emaGEN and the unite system;
Section 3.9.3 and Section 3.9.4, below, describe:
 making the data connections between: 
-- the first and, if present, fourth or last, 
emaGEN-PC card -- 
and the OCD card(s) in the 
unite system cabinet;
 making the audio connection between: 
-- each 
emaGEN card in the emaGEN-PC 
-- and the OCD block in...

Section 3:  INSTALLATION
3-7
Table 3-1    I/O port jumper settings
3.8.2
emaGEN-PC voice mail card insertion
You must insert the 
emaGEN-PC cards into the emaGEN-PC.  
Cards can be placed in any PCI slot.
WARNING
Turn off and disconnect power to the PC,
before starting any card insertion proce-
dure.
The physical act of installation is the same as for any  other PC card. 
This procedure is not described here, since it may vary from one PC 
model to another. Refer to your PC manual for card installation...

76-110-0887/0, Issue 1
3-8
Figure 3-1    Wrist strap guarding against electrostatic discharge
3.9 SYSTEM PREPARATION AND CONNECTIONS
TO emaGEN
3.9.1 Mounting an MIM on an OCD card
Figure 3-2, below, shows the three module positions on the OCD 
card. Each OCD card can accommodate up to three cartridge mod-
ules, each serving a special option function. 
You must connect one MIM (multiple interface module) on the OCD 
card for each group of four 
emaGEN ports to be connected to the 
card. The MIM connects...

Section 3:  INSTALLATION
3-9
2.  You then assign voice channel and DN numbers to the ema-
GEN
 ports. 
3. Lastly, you physically connect 
emaGEN-PC cards, via the 
audio cable, junction box, and MDF, to the audio channels of the 
OCD card MIM(s).
To mount the MIM on the OCD card, perform the following steps, as 
shown in Figure 3-2, below:
1. Place the OCD card on a soft, clean surface (a piece of sponge 
or cardboard) with the components facing up.
2. Select the position in which the MIM is to be...

76-110-0887/0, Issue 1
3-10
Figure 3-2   Inserting the MIM on the OCD card
3.9.2 Inserting an OCD card into the system cabinet
To insert an OCD card in one of the 
unite system cabinet slots, 
perform the following steps, as shown in Figure 3-3, below:
1. With the two plastic extension tabs on the end of the OCD card 
extended outwards, slide the card into the guide runners of the 
selected slot.
2. Carefully fit the card into the V-shaped insertion guides.
3. Ensure that the female connector on the card...

Section 3:  INSTALLATION
3-11
Figure 3-3   OCD card insertion 
3.9.3 Completing the data connection
The first 
emaGEN card in the emaGEN-PC connects, as 
described below, directly to the OCD card in the 
unite system cab-
inet, by means of the RJ45 connector located at the end of  the OCD 
card. If two, or more, 
emaGEN-PC cards are installed, you connect 
only the first 
emaGEN-PC card, card number 1, to the OCD card. If 
four, or more, 
emaGEN-PC cards are installed, you must connect 
the fourth, or...

76-110-0887/0, Issue 1
3-12
The emaGEN-PC card connection to the OCD card is by means of 
a cable, shown in Figure 3-4 terminated by:
 A 9-pin D-type female connector on the 
emaGEN-PC com port;
 An RJ45 male connector on the OCD card end of the cable.
Figure 3-4    Data cable from 
emaGEN card to OCD card
The wire functions and connections for the 
emaGEN-PC card to 
the OCD card data cable are shown in Table 3-1.
Table 3-2     Connections of data cable from emaGEN-PC card 
to OCD card
3.9.4...

Section 3:  INSTALLATION
3-13
Figure 3-5   emaGEN cabling from emaGEN-PC to OCD card
Note in the Figure 3-5, that:
 Connector J3 on the 
emaGEN-PC card connects to the OCD 
card containing the MIM by means of a cable, shown in Figure 3-
6, terminated by an RJ11 connector on both ends.
Each of the terminal pairs in the junction box is connected, via a 
pair of wires, as shown in Figure 3-6, to the audio terminals in the 
MDF of the corresponding voice channel utilized as an 
ema-
GEN
 port.
 A standard...

76-110-0887/0, Issue 1
3-14
The wire functions and connections for the audio cable from the 
emaGEN-PC card to a junction box, and from that junction box to 
the MDF, are shown in Figure 3-6. For a detailed description of the 
unite system cabinet to MDF connections, refer to the unite family 
of systems Installation manual.
.
Figure 3-6   Audio cable from 
emaGEN-PC voice mail card 
to four port junction box
Figure 3-7, below, shows the numbers and colors of each pin of the 
25-pair cable connector from...

Section 3:  INSTALLATION
3-15
Figure  3-7     Typical 25-pair cable connector  from  OCD block in MDF
3.10 ADDITIONAL STEPS BEFORE ACTIVATING emaGEN
Although you have made all the required physical connections 
between the 
emaGEN-PC and the unite system, you are not yet 
ready to activate 
emaGEN. You must now carry out the following 
steps: