Samsung 750 Lcd Tv User Manual

							
English - 79

Using the Message Function
Using this function, you can view the call arrivals, text message conten\
ts and schedules set on the mobile phone through the alarm window while watching TV. 
To disable this Message alarm window, set Message to Off in Setup of the Home Network Center.
The alarm window appears for 20 seconds. If no key is pressed or if Cancel is selected, it appears up to three times at 5 minute intervals.
If OK is selected, or if OK is not selected while the message is display\
ed three times, the message will be deleted. The message is not deleted from the mobile phone. 
The simple alarm window can be displayed, while using some applications \
such as Media Play, Contents Library, etc. In this case, to view the contents of the message, switch to TV viewing mode.
When the message of an unknown mobile phone is displayed, select the mob\
ile phone in the Message item of the Home Network Center and select Denied to block the phone.
Message View
If a new text message (SMS) arrives while you are watching TV, the alarm window appears. If you click the OK button, the contents of the message are displayed.
If you select the OK button, the contents of the message are displayed.
If you select the Cancel button, the alarm window appears up to three times at 5 minute intervals.
You can configure the viewing settings for the text message (SMS) conte\
nts on the mobile phone. For the procedures, refer to the mobile phone manual.
Some special characters may be displayed as blank or broken characters.
Call Arrival Alarm
If a call arrives while you are watching TV, the alarm window appears.
If you select the OK button, the call arrival alarm is confirmed and the alarm window is closed.
If you select the Cancel button, the alarm window appears up to three times at 5 minute intervals.
Schedule Alarm
While you are watching TV, the alarm window appears to display the registered schedule.
If you select the OK button, you can view the contents of the schedule registered on the mobile phone.
If you select the Cancel button, the alarm window appears up to three times at 5 minute intervals.
You can configure the viewing settings for the schedule contents on the m\
obile phone. For the procedures, refer to the mobile phone manual.
Some special characters may be displayed as blank or broken characters.
¦
N
N
N
N
N
●
●
N
N
●
●
●
●
N
N
851.86MB/993.02MB	Free
Photo
SUM
SUM		Device
PHOTO
R	ReturnMusicMovieSetuphusband
husbandSMS
OKCancel
New	message	received
Do	you	want	to	view the	details?
husbandSMS
OKCancel
New	message	received
Do	you	want	to	view	 the	details?
husbandCall
OKCancel
You	have	a	phone	call
Mom011-298-2030
husband
Scheduled	event
OKCancel
You	have	a	schedule
Do	you	want	to	view	 the	details?

[750-NA]BN68-02111B-Eng.indb   792009-03-30   �� 1:43:15 
						

							
English - 80

Using the Media Function
An alarm window appears informing the user that the media contents (vid\
eos, photos, music) sent from the mobile phone will be displayed on the TV.
The contents are played automatically 3 seconds after the alarm window a\
ppears.
If you press the RETURN or EXIT button when the alarm window appears, the Media Contents are not played.
To turn off the media contents transmission from the mobile phone, set Media to Off in Setup of the Home Network Center.
The contents may not be played on the TV depending on their resolution and format.
Media play control buttons
ButtonOperations
◄/►Move the cursor and select an item.While playing a movie file: skip forwards or backwards through the movie file.
ENTEREPressing the ENTERE button during play pauses the play.Pressing the ENTERE button during pause resumes the play.
RETURNReturn to the previous menu.
TOOLSRun various functions from the Photo, Music and Movie menus.
INFOShow file information.
EXITStop Media Play mode and Returns to TV mode.
The ENTERE and ◄/► buttons may not work depending on the type of media content.
Using the mobile device, you can control playing media. For details, ref\
er to each user’s guide.
¦
N
N
N
N
Media	will	be	played	from	“111-1234-5671”

[750-NA]BN68-02111B-Eng.indb   802009-03-30   �� 1:43:16 
						

							
English - 81

RECOMMENDATIONS
Troubleshooting
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, call Samsung customer service at 1-800-SAMSUNG.
ProblemPossible Solution
Poor picture.Try another channel. / Adjust the antenna. / Check all wire connections.
Poor sound quality.Try another channel. / Adjust the antenna.
No picture or sound.Try another channel. / Press the SOURCE button.
Make sure the TV is plugged in. / Check the antenna connections.
No sound or sound is too low at maximum volume.First, check the volume of units connected to your TV (digital broadcasting receiver, DVD, cable broadcasting receiver, VCR, etc.). Then, adjust the TV volume accordingly.
Picture rolls vertically.Check all wire connections.
There is a problem with the pictureRun the Picture test in the Self diagnostic menu.
There is a problem with the soundRun the Sound test in the Self diagnostic menu.
The TV operates erratically.Unplug the TV for 30 seconds, then try operating it again.
The TV won’t turn on.Make sure the wall outlet is working.
Remote control malfunctions.Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check the battery terminals.
‘Check signal cable’ message.Ensure that the signal cable is firmly connected to the PC source.
‘Not Supported Mode’ message.Check the maximum resolution and connected device’s Video frequency.
Compare these values with the data in the Display Modes.
Digital broadcasting screen problem.Please check the digital signal strength and input antenna.
The image is too light or too dark.Adjust the Brightness and Contrast. / Adjust the Fine tuning.
Black bars on the screen.Make sure the broadcast you’re receiving is High Definition (HD).
HD channels sometimes broadcast Standard Definition (SD) programming, which can cause black bars.
Set your cable/satellite box to stretch or widescreen mode to eliminate \
the bars.
Picture has a Red/Green or Pink tint.Make sure the Component cables are connected to the correct jacks.
Closed Captioning not working.If you are using a Cable/Satellite box, you must set Closed Captioning o\
n the box, not your TV.
Snowy picture.Your cable box may need a firmware upgrade. Please contact your Cable company.
Ghosting on picture.This is sometimes caused by compatibility issues with your cable box.
Try connecting Component cables instead.
Horizontal bars appear to flicker, jitter or shimmer on the image.Adjust the Coarse tuning and then adjust the Fine tuning.
Vertical bars appear to flicker, jitter or shimmer on the image.Adjust the Coarse tuning and then adjust the Fine tuning.
Screen is black and power indicator light blinks steadily.On your computer check: Power, Signal Cable.
The TV is using its power management system.
Move the computer's mouse or press any key on the keyboard.
¦

[750-NA]BN68-02111B-Eng.indb   812009-03-30   �� 1:43:16 
						

							
English - 82

ProblemPossible Solution
Image is not stable and may appear to vibrate when you have a computer connected to the PC input.
If the setting is not correct, use your computer utility program to chan\
ge the display settings.
Your TV supports multiscan display functions within the following frequency d\
omain:
- Horizontal frequency (KHz): 30~60
- Vertical frequency (Hz): 60~75
- PC Maximum refresh rate (at 60 Hz): 1920 x 1080
Image is not centered on the screen.Adjust the horizontal and vertical position.
The screen position must be adjusted on the output source (i.e. STB) w\
ith a digital signal.
The picture appears distorted in the corner of the screen.If Screen Fit is selected with some external devices, the picture may appear distorte\
d in the corner of the screen. This symptom is caused by the external devices, not TV.
The ‘Resets all settings to the default values.’ message appears.This appears when you press and hold the EXIT button for a while. The product settings are reset to the factory defaults.
This TFT LCD panel uses a panel consisting of sub pixels (6 220 800) which req\
uire sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
Installing the Stand
1. Attach your LCD TV to the stand.
Two or more people should carry the TV.
Make sure to distinguish between the front and back of the stand when attaching it.
To make sure the TV is installed on the stand at a proper level, do not apply excess downward pressure to the upper left of right sides of the TV.
2. 
Fasten screws at position 1 and then fasten screws at position 2.
Stand the product up and fasten the screws. If you fasten the screws wit\
h the LCD TV placed down, it may lean to one side.
Disconnecting the Stand
1. Remove screws from the back of the TV.
2. 
Separate the stand from the TV.
Two or more people should carry the TV.
. 
Cover the bottom hole with the cover.
N
¦
N
N
N
N
¦
N
2
1

[750-NA]BN68-02111B-Eng.indb   822009-03-30   �� 1:43:17 
						

							
English - 8

Assembling the Cables
Enclose the cables in the Holder-Wire Cable so that the cables are not v\
isible through the transparent stand.
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Standard dimensions for wall mount kits are shown in the table above.
When purchasing our wall mount kit, a detailed installation manual and a\
ll parts necessary for assembly are provided.
Do not use screws longer than the standard dimension, as they may cause \
damage to the inside of the TV set.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
Do not fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA  or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our dedicated wall mount kit for this model.
Do not exceed 15 degrees tilt when mounting this TV.
Product FamilyinchesVESA Spec. (A * B)Standard ScrewQuantity
LCD-TV
19~22100 X 100M4
4
23~29200 X 100
30~40200 X 200M6
46~55400 X 400
M857~70800 X 400
80~1400 X 800
PDP-TV
42~50400 X 400
M8458~63600 X 400
70~800 X 400
80~1400 X 800
LFD
30~39200 X 200M6
440~52400 X 400
M855~70800 X 400
70~1400 X 800
Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.
¦
¦
N
N
N
N
N
N
N
N
N

[750-NA]BN68-02111B-Eng.indb   832009-03-30   �� 1:43:17 
						

							
English - 84

Anti-Theft Kensington Lock
The Kensington Lock is a device used to physically fix the system when u\
sing it in a public place. The appearance and locking method may differ from the illustration depending on the manufacturer.
Refer to the manual provided with the Kensington Lock for proper use. 
The locking device has to be purchased separately.
The location of the Kensington Lock may depending on its model.
1. Insert the locking device into the Kensington slot on the LCD TV (1) and turn it in the locking direction (2).
2. Connect the Kensington Lock cable (3).
. Fix the Kensington Lock to a desk or a heavy stationary object.
N
N
Securing the Installation Space
Keep the required distances between the product and other objects (e.g.\
 walls) to ensure proper ventilation. 
Failing to do so may result in fire or a problem with the product due to\
 an increase in the internal temperature of the product.
Install the product so the required distances shown in the figure are ke\
pt. 
When using a stand or wall-mount, use parts provided by Samsung Electron\
ics only.
If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to the product falling.
If you use parts provided by another manufacturer, it  may result in a problem with the product or fire due to an increas\
e in the internal temperature of the product due to poor ventilation.
The appearance may differ depending on the product.
When installing the product with a standWhen installing the product with a wall-mount
¦
¦
N


N
3
1
2
10 cm
10 cm
10 cm
10 cm
10 cm10 cm
10 cm

[750-NA]BN68-02111B-Eng.indb   842009-03-30   �� 1:43:17 
						

							
English - 8

Securing the TV to a Wall or Cabinet
[
Caution: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang over or destabilize the TV; doing so may cause the TV to tip over, causing serious injuries or death. Follow all safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.
Components (Depending on the model): 
To prevent the TV from falling:
1.  Attach the TV-Holder to the TV by fastening the screws 1 (M4XL16) into the holes in the center of the TV.
Make sure to only use the supplied screws.
 2.  Firmly fasten the screws to the wall or cabinet where the TV is to be installed. Tie the TV-Holder attached to the TV and the screws fastened on the wall or cabinet so that the TV is fi xed. 
Purchase the screws to be used on the wall or cabinet separately.
Install the TV close to the wall so that it does not fall.
When attaching the TV to the wall, tie the cord level with the ground or slanted downwards for safety purposes.
Confi rm that the cord or link does not come loose.
Before moving the TV, separate the connected cord fi rst.
. Verify all connections are properly secured. Periodically check connectio\
ns for any sign of fatigue or failure. If you have any doubt about the security of your connections, contact a professional ins\
taller.
¦


N
N
N
N
N
N
cabinetcabinet
cabinet
TV-HolderScrew 1 (M4XL16)

[750-NA]BN68-02111B-Eng.indb   852009-03-30   �� 1:43:18 
						

							
English - 86

Specifications
Model NameLN40B70
Screen Size (Diagonal)40 inches(40.0 inches measured diagonally)
PC Resolution(Optimum)1920 x 1080 @ 60 Hz
Sound(Output)10W x 2
Dimensions (WxDxH)BodyWith stand38.7 x 3.1 x 24.8 (inch) / 984.0 x 78.6 x 629.2 (mm)38.7 x 10.0 x 27.2 (inch) / 984.0 x 255.0 x 691.5 (mm)
WeightWithout StandWith Stand32.6 lbs / 14.8 Kg41.2 lbs / 18.7 Kg
Environmental ConsiderationsOperating TemperatureOperating HumidityStorage TemperatureStorage Humidity
10°C to 40°C (50°F to 104°F)10% to 80%, non-condensing-20°C to 45°C (-4°F to 113°F)5% to 95%, non-condensing
Stand Swivel(Left / Right)-20˚ ~ 20˚
Model NameLN46B70
Screen Size (Diagonal)46 inches(46.0 inches measured diagonally)
PC Resolution(Optimum)1920 x 1080 @ 60 Hz
Sound(Output)10W x 2
Dimensions (WxDxH)BodyWith stand43.9 x 3.1 x 27.7 (inch) / 1115.0 x 78.6 x 702.5 (mm)43.9 x 10.8 x 30.3 (inch) / 1115.0 x 275.0 x 769.5 (mm)
WeightWithout StandWith Stand41.7 lbs / 18.9 Kg52.7 lbs / 23.9 Kg
Environmental ConsiderationsOperating TemperatureOperating HumidityStorage TemperatureStorage Humidity
10°C to 40°C (50°F to 104°F)10% to 80%, non-condensing-20°C to 45°C (-4°F to 113°F)5% to 95%, non-condensing
Stand Swivel(Left / Right)-20˚ ~ 20˚
¦

[750-NA]BN68-02111B-Eng.indb   862009-03-30   �� 1:43:18 
						

							
English - 87

Model NameLN2B70
Screen Size (Diagonal)52 inches(52.0 inches measured diagonally)
PC Resolution(Optimum)1920 x 1080 @ 60 Hz
Sound(Output)10W x 2
Dimensions (WxDxH)BodyWith stand49.5 x 3.1 x 31.3 (inch) / 1258.0 x 79.9 x 795.1 (mm)49.5 x 12.0 x 33.8 (inch) / 1258.0 x 305.0 x 858.5 (mm)
WeightWithout StandWith Stand64.8 lbs / 26.1 Kg76.5 lbs / 31.0 Kg
Environmental ConsiderationsOperating TemperatureOperating HumidityStorage TemperatureStorage Humidity
10°C to 40°C (50°F to 104°F)10% to 80%, non-condensing-20°C to 45°C (-4°F to 113°F)5% to 95%, non-condensing
Stand Swivel(Left / Right)-20˚ ~ 20˚
Design and specifications are subject to change without prior notice.
This device is a Class B digital apparatus.
For the power supply and Power Consumption, refer to the label attached \
to the product.
N
N
N

[750-NA]BN68-02111B-Eng.indb   872009-03-30   �� 1:43:18 
						

							
English - 88

Dimensions
LN40B70
TOP VIEW
JACK PANEL DETAIL .2"H X 6.6"W
FRONT VIEW / SIDE VIEW 
REAR VIEW
NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the dimensions prior to performing installation of your TV. Not responsible for typographical or printed errors. 
© 2009 Samsung Electronics America, Inc
¦
38.7
34.8
19.6
24.8
27.2
20.5
3.1
10.0
7.9 (200 mm)
7.9 (200 mm)

[750-NA]BN68-02111B-Eng.indb   882009-03-30   �� 1:43:19