Samsung 750 Lcd Tv User Manual

							
English - 29

Time Zone
Select your time zone.
This function is only available when Clock Mode is set to Auto.
DST	(Daylight	Saving	Time)	→	Off / On / Auto
Switches the Daylight Saving Time function on or off.
This function is only available when Clock Mode is set to Auto.
Sleep Timer
The sleep timer automatically shuts off the TV after a preset time (30, 60, 90, 120, 150 and 180 minutes).
Press the TOOLS button to display the Tools menu. You can also set the sleep timer by selecting Tools	→	Sleep	Timer.
To cancel the Sleep Timer function, select Off.
Timer 1 / Timer 2 / Timer 
Three different on / off timer settings can be made.
You must set the clock first.
On Time
Set the hour, minute, am/pm, and activate / inactivate.
(To activate the timer with the setting you’ve chosen, set to Activate.)
Off Time
Set the hour, minute, am/pm, and activate / inactivate.
(To activate the timer with the setting you’ve chosen, set to Activate.)
Volume
Set the desired volume level.
Source	→	TV	/	USB	/	TV	Memory
You can select the TV, TV Memory or USB device content to be played when the TV turns on automatically. Select TV, TV Memory or USB. (Make sure that an USB device is connected to your TV.)
When there is only one photo file in the USB or the TV Memory, the Slide Show will not play.
Antenna (when Source is set to TV)
Select Air or Cable.
Channel (when Source is set to TV)
Select the desired channel.
Contents (when Source is set to USB or TV Memory)
You can select a folder on the USB Device/TV Memory with music or photo f\
iles to be played when the TV turns on automatically.
If the folder name is too long, the folder can not be selected.
If you are using two of the same type USB device, be sure the folder nam\
es are different so the correct USB is read.
Repeat
Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual.
When Manual is selected, press the ► button to select the desired day of the week. Press the ENTERE button over the desired day and the c mark will appear.
You can set the hour, minute and channel by pressing the number buttons on the remote control.
Auto Power Off
When you set the timer on, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by the timer. This function is only available in timer on mode and prevents overheating, which may occur if a TV is on for too long time.
■
N
■
N
❑
T
N
❑
■
■
■
■
N
■
■
■
N
N
■
N
N
N
On	Time	
L	Move				U	Adjust				E	Enter					R	Return
Timer	1
Off	Time
Volume
00
00
10SourceAntennaChannelTVAir0
RepeatOnceSunMonTueWedThuFriSat
00amInactivate
00amInactivate

[750-NA]BN68-02111B-Eng.indb   292009-03-30   �� 1:42:51 
						

							
English - 0

Network Connection
You can set up the Internet Protocol so that you can communicate with var\
ious connected networks.
Network Connection - Cable
LAN Connection for a DHCP Environment
The procedures to set up the network using Dynamic Host Configuration Pr\
otocol (DHCP) are described below. Since an IP address, subnet mask, gateway, and DNS are automatically allocated when DHCP is selected, you do not have to enter them manually.1. 
Connect the LAN port on the rear panel of the TV and the external modem with a LAN Cable.
2. 
Connect the Modem port on the wall and the external modem with a Modem C\
able.
You can connect the LAN via a Sharer (Router).
You can connect the LAN port and the TV directly depending on your network status.
The terminals (the position of the port and the type) of the external \
device may differ depending on the manufacturer.
If the IP address allocation by the DHCP server has failed, turn the external modem off, turn it on again after at least 10 seconds and then try again.
For the connections between the external modem and the Sharer (Router)\
, refer to the owner’s manual of the corresponding product.
You can connect the TV to the LAN directly without connecting it through a Sharer (Router)
You cannot use a manual-connection-type ADSL modem because it does not support DHCP. You have to use an automatic-connection-type ADSL modem.
¦
❑
■
N
N
N
N
N
TV Rear PanelThe Modem Port on the WallExternal Modem (ADSL / VDSL / Cable TV)
1 LAN Cable2 Modem Cable
TV Rear PanelThe Modem Port on the WallExternal Modem (ADSL / VDSL / Cable TV)
LAN CableModem CableLAN Cable
IP Sharer
TV Rear PanelThe LAN Port on the Wall
LAN Cable

[750-NA]BN68-02111B-Eng.indb   302009-03-30   �� 1:42:51 
						

							
English - 1

LAN Connection for Static IP Environment
The procedures to set up the network using a static IP address are described below. You have to manually enter the IP address, subnet mask, gateway, and DNS that are provided by your Internet Service Provider (ISP). 1. 
Connect the LAN port on the rear panel of the TV and the LAN port on the wall using the LAN cable.
You can connect the LAN via a Sharer (Router).
The terminals (the position of the port and the type) of the external \
device may differ depending on the manufacturer.
If you are using a static IP address, your ISP will inform you of the IP address, subnet mask, gateway, and DNS. You must enter these values to complete the network settings. If you do not know \
the values, ask your network administrator.
For the information on how to configure and connect a Sharer (Router),\
 refer to the owner’s manual for the corresponding product.
You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
If you use an IP Sharer (IP Router) that supports DHCP, you can set up the device as either DHCP or static IP.
For the procedures to use a static IP address, ask your Internet Service Provider.
■
N
N
N
N
N
N
TV Rear PanelThe LAN Port on the WallIP Sharer
LAN CableLAN Cable
TV Rear PanelThe LAN Port on the Wall
1 LAN Cable

[750-NA]BN68-02111B-Eng.indb   312009-03-30   �� 1:42:52 
						

							
English - 2

Network Connection - Wireless
You can connect to the network wirelessly through a wireless IP sharer.
1. Connect the ‘Samsung Wireless LAN Adapter’ into the USB1(HDD) or USB2 terminal of the TV.
You must use the ‘Samsung Wireless LAN Adapter’(WIS09ABGN) to use a wireless network.
Samsung’s Wireless LAN adapter is sold separately. The WIS09ABGN Wireless LAN adapter is offered by select retailers, Ecommerce sites and Samsungparts.com.
To use a wireless network, your TV must be connected to a wireless IP sharer. If the wireless IP sharer supports DHCP, your TV can use a DHCP or static IP address to connect to the wireless network.
Samsung’s Wireless LAN adapter supports IEEE 802.11A, IEEE 802.11B, IEEE 802.11G, IEEE 802.11N. When you play DLNA video over IEEE 802.11B/G connection, the video may not be played smoothly.
If the wireless IP sharer allows you to turn the Ping connection function on/off, turn it on.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wir\
eless IP sharer is currently being used by another device nearby, this will result in interference and communications may fail.
If you apply a security system other than the systems listed below, it will not work with the TV. 
When applying the security key for the AP (wireless IP sharer), only the following is supported.
1) Authentication Mode : OPEN, SHARED, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
When applying the security key for the Ad-hoc mode, only the following is supported.
1) Authentication Mode : SHARED, WPANONE
2) Encryption Type : WEP, TKIP, AES
If your AP supports WPS(Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Configuration) or PIN (Personal Indentification Number). WPS will automatically configur\
e the SSID and WPA key in either mode.
If the device isn’t certified, it may not connect to the TV via the ‘Samsung Wireless LAN Adapter’.
❑
N
N
N
N
N
N
N
•
•
N
N
or
TV Side Panel
The LAN Port on the WallWireless IP sharerSamsung Wireless LAN Adapter
LAN Cable

[750-NA]BN68-02111B-Eng.indb   322009-03-30   �� 1:42:52 
						

							
English - 

Setting the Network
Network Type
Select Cable or Wireless as the method to connect to the network.
The menu is activated only if the ‘Samsung Wireless LAN Adapter’ is connected. 
Cable
Connect to the network using a cable.
Wireless
Connect to the network wirelessly.
Network Setup 
Cable Network Setup (when Network Type is set to Cable)
Please check if the LAN cable is connected.
Internet	Protocol	Setup	→	Auto	Setup	/	Manual	Setup
Network Test: You can test or confirm the network connection status after setting up th\
e network.
When unable to connect to a wired network
If your Internet service provider has registered the MAC address of the \
device used to connect to the Internet for the first time and authenticates the MAC address each time you connect to the Internet,\
 your TV may not be able to connect to the Internet as the MAC address differs from that of the device (PC).
In this case, ask your Internet service provider about the procedures to\
 connect devices other than your PC (such as your TV) to the Internet. If your Internet service provider requires an ID or pas\
sword to connect to the Internet (network), your TV may not be able to connect to the Internet. In this case, you have to enter \
your ID or password when connecting to the Internet using an Internet Sharer (Router).
The internet connection may fail due to a firewall problem. In this case\
, contact your Internet service provider. If you cannot connect to the Internet even if you have followed the procedures of your\
 Internet service provider, please contact Samsung Electronics at 1-800-SAMSUNG.
Cable Network Setup-Auto Setup
If you connect the LAN cable and it supports DHCP, the Internet Protocol (IP) Settings are automatically configured. 
1. 
Set Network Type to Cable.
2. 
Select Cable Network Setup.
. 
Set Internet Protocol Setup to Auto Setup.
The Internet Protocol is set automatically.
4. 
Select Network Test to check the network connectivity.
Cable Network Setup-Manual 
To connect the TV to the LAN using a static IP address, you must set up the Internet Protocol (IP).  1. 
Set Network Type to Cable.
2. 
Select Cable Network Setup.
. 
Set Internet Protocol Setup to Manual Setup.
4. 
Set up IP Address, Subnet Mask, Gateway and DNS Server.
Press the number buttons on the remote control when you set the Network \
manually.
. 
Select Network Test to check the network connectivity.
Wireless Network Setup
The menu is activated only if the ‘Samsung Wireless LAN Adapter’ is connected.
Internet	Protocol	Setup	→	 Auto	Setup	/	Manual	Setup
Network Test: You can test or confirm the network connection status after setting up th\
e network.
¦
❑
N
■
■
❑
■
N
●
●
N
N
N
■
N
●
●
Internet	Protocol	Setup	 :	Auto	Setup	 	 ▶
Network	Test
U	Move					E	Enter					R	Return
Cable	Network	Setup
IP	Address	 :										Subnet	Mask	:										Gateway	:											
DNS	Server	 :										
Internet	Protocol	Setup	 :	Manual	Setup	 	 ▶
Network	Test
U	Move					E	Enter					R	Return
Cable	Network	Setup
IP	Address	:	0			0			0			0Subnet	Mask	:	0			0			0			0Gateway	:	0			0			0			0	
DNS	Server	 :	0			0			0			0
Game	Mode	:	Off
BD	Wise	 :	On
Network	Type	 :	Cable	 ▶
Network	SetupV-ChipCaption
Melody		:	Medium
Light	Effect		 :	Watching	TV
Energy	Saving		 :	Off
PIP
Setup

[750-NA]BN68-02111B-Eng.indb   332009-03-30   �� 1:42:52 
						

							
English - 4

When unable to connect to an AP
Your TV may fail to locate an AP that is configured as a private SSID type. In this case, please change \
the AP settings and try again. If your Internet service provider has registered the MAC address \
of the device used to connect to the Internet for the first time and authenticates the MAC address each time you connect to th\
e Internet, your TV may not be able to connect to the Internet as the MAC address differs from that of the device (PC).
In this case, ask your Internet service provider about the procedures to\
 connect devices other than your PC (such as your TV) to the Internet. If you cannot connect to the Internet even if you have \
followed the procedures of your Internet service provider, please contact a Samsung Electronics at 1-800-SAMSUNG.
Select a network
Access Point: You can select the IP sharer to use when using a wireless network.
If a wireless Access Point is not in the Access Point list, press the Red button.
When the connection is made, you will be returned to the screen automati\
cally.
If you have selected an Access Point with a security authentication:
The Security Key input screen appears. Enter the security key and press \
the Blue button on the remote control.
If security encryption type is WEP, 0~9, A~F will be available when you input security key.
Connecting WPS (Wi-Fi Protected Setup)
If Security Key is already set: In access point list, select WPS.
You can select PBC, PIN, Security Key.
Connecting by using PBC: Select a PBC (Push Button Configuration). Press the PBC button on the AP (access point) within 2 minutes, and wait for connection.
Connecting by using PIN: Select a PIN (Personal Identification Number). 
The message showing the PIN Code is displayed. Input the PIN Code at AP device within 2 minutes. Select OK and wait for connection.
Try again if connecting operation doesn’t work
When the connection is not established although tried again, reset the a\
ccess point. Please refer to a manual of each access point.
Connecting by using Security Key: When selecting Security Key, the input window is displayed. Input the security key and press Blue button.
Try again if connecting operation doesn’t work.
If Security Key is not set: When the security setting of AP that supports WPS is NONE, you can select PBC, PIN, None Security. None Security is capable of connecting to AP directly without using WPS function.
Process of PBC, PIN is same as above. Refer to if Security Key is already set.
Try again if connecting operation doesn’t work.
N
●
•
N
N
N
N
●
N
•
•
N
N
N
•
N
●
N
N
Wireless	Network	Setup
	U	Move					E	Enter					R	Return
Select	a	network3/9
	Search	Ad-hoc
ssonjeeAP_1Ap_2
PBCPIN
Security	Key
Cancel
Press	the	PBC	button	on	the	access	point.
Access	Point	Name	:	AP_1
Press	OK	After	input	TV’s	Pincode	in	the	access	
point’s	setup.
Access	Point	Name	:	AP_1
PIN	Code	:	12345678
CancelOK
Wireless	Network	Setup
	n	Move						`~9	Number					E	Enter					R	Return
Security	Key	Number		Lowercase		Delete		Done
AHOV
BIPW
CJQX
DKRY
ELSZ
FMT
GNU
Wireless	Network	Setup
	U	Move					E	Enter					R	Return
Select	a	network3/9
	Search	Ad-hoc
ssonjeeAP_1Ap_2
PBCPIN
None	Security
Wireless	Network	Setup
	n	Move				`~9	Number				E	Enter				R	Return
Security	Key	Number		Delete		DoneABCDEF

[750-NA]BN68-02111B-Eng.indb   342009-03-30   �� 1:42:53 
						

							
English - 

Ad-hoc: You can connect to a mobile device without an access point through the ‘\
Samsung Wireless LAN Adapter’ by using a peer to peer network.
How to connect to new Ad-hoc
1. Choose Select a network, then a device list is displayed.
2. 
While in the device list, press the Blue button on the remote or select \
Ad-hoc.
The message The existing network system may have limited functionality. Do you want to change the network connection? is displayed.
. 
Input the generated Network Name(SSID) and Security Key into the device you want to connect.  
N
How to connect an existing Ad-hoc device
1. Choose Select a network, the device list is displayed.
2. 
Select the device you want in the Device list.
. 
If security key was applied, input the security key again.
If network doesn’t operate normally, please check the Network Name(SSID) and Security Key again. If the Security Key is incorrect, 
it may be the reason for the malfunction.
N
Wireless Network Setup-Auto Setup
If you want to connect AP, AP should support DHCP. Only devices which support Ad-hoc mode can be connected without DHCP. 1. 
Set Network Type to Wireless.
2. 
Select Wireless Network Setup.
. 
Set Internet Protocol Setup to Auto Setup.
The Internet Protocol is set automatically.
4. 
Select a network through Select a network.
. 
Select Network Test to check the network connectivity.
Wireless Network Setup-Manual Setup
1. Set Network Type to Wireless.
2. 
Select Wireless Network Setup.
. 
Set Internet Protocol Setup to Manual Setup.
4. 
Set up IP Address, Subnet Mask, Gateway and DNS Server.
Press the number buttons on the remote control when you set the Network \
manually.
. 
Select a network through Select a network.
6. 
Select Network Test to check the network connectivity.
•
N
N
Internet	Protocol	Setup	 :	Auto	Setup	 	 ▶
Network	Test
Select	a	network		 :	AP1
U	Move					E	Enter					R	Return
Wireless	Network	Setup
IP	Address	:										Subnet	Mask	:										Gateway	:											
DNS	Server	 :										
Internet	Protocol	Setup	 :	Manual	Setup	 		 ▶
Network	Test
Select	a	network		 :	AP1
U	Move					E	Enter					R	Return
Wireless	Network	Setup
IP	Address	:	0			0			0			0Subnet	Mask	:	0			0			0			0Gateway	:	0			0			0			0	
DNS	Server	 :	0			0			0			0
The	existing	network	system	may	have	limited	
functionality.	Do	you	want	to	change	the	network	
connection?
Yes	No	

[750-NA]BN68-02111B-Eng.indb   352009-03-30   �� 1:42:53 
						

							
English - 6

INPUT / SUPPORT
Input Menu
Source List
Use to select TV or other external input sources such as DVD / Blu-ray players / Cable Box /
Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.
Press the SOURCE button on the remote control to view an external signal source.
TV / AV1 / AV2 / Component1 / Component2 / PC / HDMI1/DVI / HDMI2 / HDMI / HDMI4 / USB
You can choose only those external devices that are connected to the TV. In the Source List, connected inputs will be highlighted and sorted to the top. Inputs tha\
t are not connected will be sorted to the bottom. 
If USB devices are connected to the USB1(HDD) and USB2 jacks, they are displayed as USB1 and USB2 in order.
PC always stays activated.
Using the color buttons on the remote with the Source list
Red (Refresh): Refreshes the connected external devices. Press this if your Source \
is on and connected, but does not appear in the list.
TOOLS (Tools): Displays the Edit Name and Information menus.
Edit Name
VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI / DVI PC / TV / IPTV / Blu-ray / HD DVD / DMA
Name the device connected to the input jacks to make your input source s\
election easier.
When a PC with a resolution of 1920 x 1080@60Hz is connected to the HDMI IN 1(DVI) port, you should set the HDMI1/DVI mode to DVI PC in the Edit Name of the Input mode.
Support Menu
Legal Notice
View the Legal Notice and General Disclaimer regarding Third Party Contents and Service.
The General Disclaimer may differ depending on the country.
Product Guide
The Product Guide gives you information on the most important features o\
f this TV.
The descriptions provided by this function are in Engligh and French onl\
y.
Picture QualityFull HD 1080p
Auto Motion Plus 240Hz
Picture Mode
[email protected]@TV-Content Service
Content Library Flash
USB2.0 Movie
DLNA Wireless
Eco-FriendlyEnergy Saving Mode
Eco Material
¦
❑
O
■
N
N
N
N
•
•
❑
■
N
¦
❑
N
❑
Legal	Notice	 	▶
Product	Guide
Self	Diagnosis
Software	Upgrade
HD	Connection	Guide
Contact	Samsung
Support
Source	List	 	
Edit	Name
Input
			Refresh					T	Tools
Source	List
TV
PC	:	-	-	-	-
AV1	 :	-	-	-	-
AV2	 :	-	-	-	-
Component1	 :	-	-	-	-
Component2		 :	-	-	-	-

[750-NA]BN68-02111B-Eng.indb   362009-03-30   �� 1:42:54 
						

							
English - 7

Using the Remote Control Buttons in the Product Guide Menu
ButtonOperations
Yellow ButtonShows the contents of the Product Guide sequentially. (Auto Play)
◄/►Move the cursor and select an item.
ENTERESelect the currently selected item.
RETURNReturn to the previous menu.
EXITStop the current function and return to the Product Guide main menu.
Self Diagnosis
Picture Test
If you think you have a picture problem, perform the picture test. Check\
 the color pattern on the screen to see if the problem still exists.
Yes: If the test pattern does not appear or there is noise in the test patt\
ern, select Yes. There may be a problem with the TV. Contact Samsung’s call center for assistance.
No: If the test pattern is properly displayed, select No. There may be a problem with your external equipment. Please check your connections. If the problem still \
persists, refer to the external device’s user manual.
Sound Test
If you think you have a sound problem, please perform the sound test. You can check the sound by playing a built-in melody sound through the TV.
If you hear no sound from the TV’s speakers, before performing the sound test, make sure Speaker Select is set to TV speaker in the Sound menu.
The melody will be heard during the test even if Speaker Select is set to External Speaker or the sound is muted by pressing the MUTE button.
Yes: If during the sound test you can hear sound only from one speaker or n\
ot at all, select Yes. There may be a problem with the TV. Contact Samsung’s call center for assistance.
No: If you can hear sound from the speakers, select No. There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to the external d\
evice’s user manual.
Signal Strength (digital channels only)
Unlike analog channels, which can vary in reception quality from ‘sno\
wy’ to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog\
 channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital chan\
nels.
If the signal strength meter indicates that the signal is weak, physical\
ly adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the\
 strongest signal.
❑
■
●
●
■
N
N
●
●
■
N
Self	Diagnosis
U	Move						E	Enter					R	Return
Picture	Test			▶
Sound	Test
Signal	Information

[750-NA]BN68-02111B-Eng.indb   372009-03-30   �� 1:42:54 
						

							
English - 8
Software Upgrade
Samsung may offer upgrades for the TV’s firmware in the future. These upgrades can be performed via the TV when it is connected to the Internet, or by downloading the new firmware from samsung.com to a USB memory device.
Current Version is the software already installed in the TV.
Alternative Software (Backup) shows the previous version that will be replaced.
Software is represented as ‘Year/Month/Day_Version’. The more recent the date, the newer the software version. Installing the latest version is recommended\
.
By USB
Insert a USB drive containing the firmware upgrade downloaded from samsu\
ng.com into the TV. Please be careful to not disconnect the power or remove the USB drive \
while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Please check the firmware version after the upgrades are comple\
te (the new version will have a higher number than the older version).
When software is upgraded, video and audio settings you have made will r\
eturn to their default (factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.
By Online
Upgrades the software using the Internet. 
First, configure your network. For detailed procedures on using the Network Setup, refer to the ‘Set\
ting the Network’ instructions. (see pages 30~35)
If the internet connection doesn’t operate properly, connection can be broken. please retry downloading. If the problem still happens, download by USB and upgrade.
Alternative Software (Backup)
If there is an issue with the new firmware and it is affecting operation, you can change the software to the previous version.
If software was changed, existing software is displayed.
You can change current software to alternative software by ‘Alternative Software’.
HD Connection Guide
This menu presents the connection method that provides the optimal quali\
ty for the HDTV. Refer to this information when connecting external devices to the TV.
Contact Samsung
View this information when your TV does not work properly or when you want to upgrade the software. You can view the information regarding the call center, product and software file download method.
❑
N
N
N
■
■
N
N
■
N
N
❑
❑
or
TV Side Panel
USB Drive
Current	Version	2009/01/17_000001
By	USB	 			▶
By	Online
Alternative	Software		 2009/01/16_000000
U	Move					E	Enter					R	Return
Software	Upgrade

[750-NA]BN68-02111B-Eng.indb   382009-03-30   �� 1:42:54